When halting a group of PEs through CTI, HDE must be set in EDSCR for
all of them.
Change-Id: Iaa4bc0b0fe31e46a463c709d8274023225affd85
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When an armv8-a PE causes an exception while halted, e.g. by performing
a prohibited memory or register access, its state is affected in the
same way as if it was running. That means, a number of registers is
overwritten (notably DLR and DSPSR, but also others) and also
potentially the exception level and therefore also the PE state can
change. This state must be restored before resuming normal operation.
This is done by marking the relevant cached registers "dirty" so that
they are written back before resume.
Change-Id: I9b6967a62d7cb23a477a9f7839f8d2b7087eed09
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use proper T32 opcodes for cache identification when the PE is in
Aarch32 state
Change-Id: I9cd9169409889273a3fd61167f388e68d8dde86d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
DCPS only allows to enter higher ELs, for lower ELs you need to
use DRPS. Also, of course the encoding differs between A64 and T32.
Both DCPS and DRPS also clobber DLR and DSPSR, which then need to be
restored on resume.
Change-Id: Ifa3dcfa94212702e57170bd59fd0bb25495fb6fd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
All register access is now performed through common read/write
functions, which delegate the actual register access to the
armv8_common object. armv8_common contains function pointers
to direct read and write requests to the respective low-level
functions for each PE state.
The respective read/write functions are selected on debug state
entry.
At the same time, T32 opcodes are now formatted for ITR in
dpmv8_exec_opcode() and the T32_FMTITR macro is removed from global
visibility.
Change-Id: I9eaef017c7cc9e0c531e693c534901bfdbdb842c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Read registers based on current EL instead of PE mode.
Change-Id: I05d3219ac1bf8585e9f4f024a7e8599fea0913b6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
There's no access to system control register in EL0. Circumvent by
moving the PE to EL1 before reading, and switch back to original mode
afterwards.
Change-Id: I309f4eea5597ffc88fc892e9bbb826982e8a44ec
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Translate from cpsr value to "enum arm_mode" by shifting up 4 bits and
filling the lowest nibble with 0xF.
Change-Id: Ic32186104b0c29578c4f6f99e04840ab88a0017b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use AT commands to translate virtual to physical addresses based on
current MMU configuration.
Change-Id: I1bbd7d674c435541b617b17022fa9f7f0f01bdab
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set HDE bit through helper function instead of manual mem_ap access.
Change-Id: I68c157870f3f3c47a875d425ade6e975d8075424
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The artificial "os_border" doesn't exist in aarch64 state and is wrong
for aarch32 state as well. Remove it.
Change-Id: I7c673a1404b03aa78dbd505e115fa3a93f7ca05f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Update cache identification to match functionality present in
armv7a_cache.c
Change-Id: I2dc4bee80f5a22b8728334d40331c183d1406f27
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move all DPM related functions from aarch64.c to armv8_dpm.c.
Change-Id: I43404ff5db414ae898787a523d3219e5bee44889
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Add database for common, equivalent opcodes for Aarch32 and
Aarch64 execution states
Revisit all functions that access Aarch64 specific registers
or use Aarch64 opcodes and rewrite them to act depending on
current state of the core.
Add core register access functions for Aarch32 state
Add function to determine the core execution state without
reading DSPSR.
Change-Id: I345e9f6d682fb4ba454e4b1d16bb5e1b27570691
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set up CTI so that halt and resume requests get routed to all PEs in the
SMP group.
Change-Id: Ie92cfd3fe54632e5fdc049a6bf5b24b99451a8c9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
For now only D-Cache flush (Clean&Invalidate) and I-Cache
invalidate are implemented. That's enough for software breakpoints.
Change-Id: I8e96d645a230b51e3490403f4564e59ba6a76cf3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
On live hardware, interrupts will happen while the core is
held for stepping. The next step will most of the time execute an
interrupt service instead of the next line of code, which is not
what you expect. Disable interrupts through DSCR before resuming
for a step, and re-enable them again after the step happened.
This should be made configurable, like on cortex_a target.
Change-Id: I94d8ffb58cf7579dedb66bc756b7eb6828b6e8e4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
External debuggers need to use HLT, not BRK. HLT generates a halting
debug event while BRK generates a debug exception for self-hosted
debugging.
Change-Id: I24024b83668107f73a14cc75d951134917269e5c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Don't report breakpoint as debug reason when halt is due to a
single-step event.
Change-Id: Ie6c3ca1e5427c73eb726a038301b6a29a47d1217
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
According to gdb documentation, a register "cpsr" is expected if
aarch64 features are announced. Also, the value buffer must be
capable of holding a 64bit value (8 byte, not 4)
Change-Id: I7aec4e84fa87eadb26797acd0d16c988b9852616
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reduce complexity of memory access functions, anyway there are no ARMv8
platforms that actually contain an AHB-AP at all. while at it, fix
virt-to-phys function signatures to expect target_addr_t.
Change-Id: I55a369686f42993988b6323e5a77f38de12530a9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The step command optionally carries a resume address. In this case,
stepping should start not at the current PC, but at the given address.
Change-Id: Id5792a3745f470cf29efa90c63d65f33d36f6b25
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
