Squash the history to reduce all the noise when rebasing.
Readme correction
Changes to support QUTS-openOCD
Changes to support QUTS-openOCD
Hexagon debug changes
License headers addition
config file update for lanai
Jimtcl submodule version correction
QUTS install instructions
Eud QPM version update in readme
EUD QPM name correction
Removed QUTS library code for EUD Service
Updated hexagon support
Added EUD submodule
Updated makefiles to compile EUD codebase with openocd
Use --enable-eud with configure command to compile with EUD
Added Qualcomm QCS6490 configuration file
Removed QUTS library code for EUD Service
Updated hexagon support
Added EUD submodule
Updated makefiles to compile EUD codebase with openocd if --enable-eud option is added with configure command
Added Qualcomm QCS6490 configuration file
Changes to read and print EUD Revision information
Signed-off-by: Ashi Gupta <quic_ashig@quicinc.com>
Added EUD Adapter option in qcs6490.cfg and updated license information
Signed-off-by: Ashi Gupta <quic_ashig@quicinc.com>
Updated the EUD submodule link and removed the newline character (\) from the target create command in the qcs6490.cfg configuration file
Signed-off-by: Ashi Gupta <quic_ashig@quicinc.com>
To alleviate the need to bitbang SWD, I've written a SWD SPI
implementation. This code is inspired by the work of luppy@appkaki.com
as shown at github.com/lupyuen/openocd-spi but with the desire to be
more generic. This implementation makes use of the more common 4 wire
SPI port using full duplex transfers to be able to capture the SWD ACK
bits when a SWD TX operation is in progress.
TEST:
Connects successfully with the following combinations:
Hosts:
Raspberry Pi 4B
Unnamed Qualcomm SoC with QUPv3 based SPI port
Targets:
Raspberry Pi 2040
Nordic nRF52840
NXP RT500
Change-Id: Ic2f38a1806085d527e6f999a3d15aea6f32d1019
Signed-off-by: Richard Pasek <rpasek@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8645
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
Previously, Linux assigned gpiochip numbers sequentially depending on
when the chip driver was probed. As RP1 is on the end of a PCIe link, it
is probed later than the on-board chips (including expanders connected
over SPI/I2C). This meant that RP1's gpiochip assignment was at an
offset that could potentially change.
A downstream kernel patch now assigns fixed offsets for RP1 and the
onboard gpiochips. Query the device tree to get proper GPIO_CHIP index.
Change-Id: I759978d4b3021c815a7d9febb41961cd1d3d185c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8650
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Provide cable specific configuration files like for the FTDI interface.
Depcrecate the old configuration files but keep them until the next
release for compatibility reasons.
Change-Id: I436bd60779a107120c9e1b1f0b8a69a39a240ad4
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8514
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The STLink API that supports dap-direct is available from STLink
firmware v2j24, published in early 2015.
We can reasonably expect that any old STLink still in use today
has got at least one firmware update during the last 10 years.
Most of the board files in upstream OpenOCD still use the STLink
in HLA mode. This limits the test coverage of the dap-direct code,
which was introduced in OpenOCD v0.11.0.
- Rename interface/stlink.cfg as interface/stlink-hla.cfg to still
provide support for HLA, adding a deprecated message.
- Rename interface/stlink-dap.cfg as interface/stlink.cfg to make
dap-direct the default trasport.
- Add a redirect file interface/stlink-dap.cfg for users that have
out-of-tree custom board files.
- Update all the board files to the new setup.
- Remove STLink HLA mentions from the documentation, while adding
a reference to interface/stlink-hla.cfg
Checkpatch-ignore: LONG_LINE
Change-Id: I99366bb03cd3b83f8f408514e657f30e59813063
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8523
Tested-by: jenkins
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
Make sure raspberrypi-native.cfg cannot be used on RPi5.
Add raspberrypi5-gpiod.cfg which uses linuxgpiod adapter driver.
Issue a warning if PCIe is in power save mode.
While on it, re-format warnings issued from Tcl to look similar
to LOG_WARNING() output.
Change-Id: If19b0350bd5fff83d9a0c65999e33b161fb6957a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8333
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The old configuration files did not work because of a missing
'at91sam9260minimal.cfg' file. Also, the config files were placed
wrongly. Update them, put them to the proper location, merge the two
supported boards into one, remove now superfluous include, remove
defunct web page, etc.. Tested with a Calao USB-A9G20 and a hacked
'device_desc' to match. Native support for it will come next.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: Iec578c8777c5a6134e132dbac17c2988c7634742
Reviewed-on: https://review.openocd.org/c/openocd/+/7522
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With the new checkpatch we will not get this type of issues
anymore.
In mean time, let's fix what we have missed during the review
process.
Change-Id: Iecebf9d43f51a29ee09505d360792793afd24b40
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 53556fcded ("tcl/interface: add Ashling Opella-LD FTDI config files")
Reviewed-on: https://review.openocd.org/c/openocd/+/7530
Tested-by: jenkins
Speed calibration coeffs are computed from cpufreq/scaling_max_freq
and from the device-tree compatibility information.
Raspberry Pi linux offers /dev/gpiomem for non-root access
to the GPIO registers since ~2016.
Do not configure 'bcm2835gpio peripheral_base' as it is necessary
only if /dev/mem is used - it requires running OpenOCD as root
- it's a security risk so it should be avoided.
The configuration of the GPIO connector (40-pin header)
is factored out and ready to use in interface configuration
for other driver (e.g. linux gpiod).
Mark raspberrypi2-native.cfg as deprecated and redirect
it to raspberrypi-native.cfg
Change-Id: Icce856fb660b45374e94174da279feb51f529908
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7264
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
