Network interface groups support added while ago, however
there is no IFLA_GROUP attribute description in policy
and netlink message size calculations until now.
Add IFLA_GROUP attribute to the policy.
Fixes: cbda10fa97 ("net_device: add support for network device groups")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 73ba57bfae ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad408 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae ("ipv6: fix backtracking for throw routes")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan911x family of devices require supplying from 3.3 V power
supplies (connected to VDD_IO, VDD_A and VREG_3.3 pins). The existing
driver however obtains only VDD_IO and VDD_A regulators in an optional
way so document this in bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur says:
====================
net: fix loadable module for DPAA Ethernet
The DPAA Ethernet makes use of a symbol that is not exported.
Address the issue by propagating the dma_ops rather than calling
arch_setup_dma_ops().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the use of arch_setup_dma_ops() that was not exported
and was breaking loadable module compilation.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure dma_ops are set, to be later used by the Ethernet driver.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 217f697436 ("net: busy-poll: allow preemption in
sk_busy_loop()") there is an explicit do_softirq() invocation after
local_bh_enable() has been invoked.
I don't understand why we need this because local_bh_enable() will
invoke do_softirq() once the softirq counter reached zero and we have
softirq-related work pending.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should avoid marking goto rules unresolved when their
target is actually reachable after rule deletion.
Consolder following sample scenario:
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100
32100: from all lookup main
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
# ip -4 ru del pref 32100 table main
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100 [unresolved]
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
After removal of first rule with preference 32100 we
mark all goto rules as unreachable, even when rule with
same preference as removed one still present.
Check if next rule with same preference is available
and make all rules with goto action pointing to it.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now before dumping a sock in sctp_diag, it only holds the sock while
the ep may be already destroyed. It can cause a use-after-free panic
when accessing ep->asocs.
This patch is to set sctp_sk(sk)->ep NULL in sctp_endpoint_destroy,
and check if this ep is already destroyed before dumping this ep.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdrver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the phy loopback self_test failed issue. when
Marvell Phy Module is loaded, it will powerdown fiber when doing
phy loopback self test, which cause phy loopback self_test fail.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).
Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.
Here is the race:
CPU 0 CPU1
- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
- acquires the mutex_lock
- allocates rdma response queues
- if FULL_INIT_DONE set,
tell uP to route ctrl queue compl
to rdma rspq
- relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock
This patch fixes the above issue.
Fixes: e7519f9926f1('cxgb4: avoid enabling napi twice to the same queue')
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
CC: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Here's just the fix for that ancient bug:
* remove wext calling ndo_do_ioctl, since nobody needs
that now and it makes the type change easier
* use struct iwreq instead of struct ifreq almost everywhere
in wireless extensions code
* copy only struct iwreq from userspace in dev_ioctl for the
wireless extensions, since it's smaller than struct ifreq
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the existing dn_route.c code, dn_route_output_slow() takes
dst->__refcnt before calling dn_insert_route() while dn_route_input_slow()
does not take dst->__refcnt before calling dn_insert_route().
This makes the whole routing code very buggy.
In dn_dst_check_expire(), dnrt_free() is called when rt expires. This
makes the routes inserted by dn_route_output_slow() not able to be
freed as the refcnt is not released.
In dn_dst_gc(), dnrt_drop() is called to release rt which could
potentially cause the dst->__refcnt to be dropped to -1.
In dn_run_flush(), dst_free() is called to release all the dst. Again,
it makes the dst inserted by dn_route_output_slow() not able to be
released and also, it does not wait on the rcu and could potentially
cause crash in the path where other users still refer to this dst.
This patch makes sure both input and output path do not take
dst->__refcnt before calling dn_insert_route() and also makes sure
dnrt_free()/dst_free() is called when removing dst from the hash table.
The only difference between those 2 calls is that dnrt_free() waits on
the rcu while dst_free() does not.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox mlx5 fixes 2017-06-14
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5: Wait for FW readiness before initializing command interface") kernels >= 4.4
("net/mlx5e: Fix timestamping capabilities reporting") kernels >= 4.5
("net/mlx5e: Avoid doing a cleanup call if the profile doesn't have it") kernels >= 4.9
("net/mlx5e: Fix min inline value for VF rep SQs") kernels >= 4.11
The "net/mlx5e: Fix min inline .." (a oneliner patch) doesn't cleanly apply
to 4.11, it hits a contextual conflict and can be easily resolved by:
+ mlx5_query_min_inline(mdev, &priv->params.tx_min_inline_mode);
to the end of mlx5e_build_rep_netdev_priv. Note the 2nd parameter of
mlx5_query_min_inline is slightly different from the original one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.
Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.
Fixes: 26e59d8077 '(net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the firmware API is partial and allows to offload only
the dscp part of the tos, also, ipv6 support isn't there yet.
As such, remove the offloading option of ipv4 dscp till the FW
APIs are more comprehensive.
Fixes: d79b6df6b1 ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we don't check that the link type is Eth and hence crash
on IB ports when attempting to deref esw->xxx, fix that.
To avoid repeating this check over and over, put the existing
checks and the one on link type in a single helper.
Fixes: 7768d1971d ('net/mlx5: E-Switch, Add control for encapsulation')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Mohamad Badarnah <mohamadb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.
This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.
Fixes: a6f402e499 ("net/mlx5e: Tx, no inline copy on ConnectX-5")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Fixes: e3297246c2 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The referenced file dsa.txt is located at
Documentation/devicetree/bindings/net/dsa/dsa.txt
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Serhey Popovych
Krzysztof Kozlowski
David S. Miller
Madalin Bucur
Sebastian Siewior
Xin Long
Lin Yun Sheng
Gao Feng
Raju Rangoju
Haishuang Yan
Wei Wang
Or Gerlitz
Chris Mi
Maor Dickman
Eli Cohen
xypron.glpk@gmx.de