Pull SoC driver updates from Arnd Bergmann:
"The driver updates again are all over the place with many minor fixes
going into platform specific code. The most notable changes are:
- Support for Microchip pic64gx system controllers
- Work on cleaning up devicetree bindings for SoC drivers, and
converting them into the new format
- Lots of smaller changes for Qualcomm SoC drivers, including support
for a number of newly supported chips
- reset controller API cleanups and a new driver for Cix Sky1
- Reworks of the Tegra PMC and CBB drivers, along with a change to
how individual Tegra SoCs get selected in Kconfig and BPMP firmware
driver updates including a refresh of the ABI header to match the
version used by firmware
- STM32 updates to the firewall bus driver and support for the debug
bus through OP-TEE
- SCMI firmware driver improvements for reliability, in particular
for dealing with broken firmware interrupts
- Memory driver updates for Tegra, and a patch to remove the unused
Baikal T1 driver"
* tag 'soc-drivers-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (193 commits)
firmware: arm_ffa: Use the correct buffer size during RXTX_MAP
firmware: qcom: scm: Allow QSEECOM on Lenovo IdeaCentre Mini X
clk: spear: fix resource leak in clk_register_vco_pll()
reset: rzv2h-usb2phy: Add support for VBUS mux controller registration
reset: rzv2h-usb2phy: Convert to regmap API
dt-bindings: reset: renesas,rzv2h-usb2phy: Document RZ/G3E USB2PHY reset
dt-bindings: reset: renesas,rzv2h-usb2phy: Add '#mux-state-cells' property
soc: microchip: add mpfs gpio interrupt mux driver
dt-bindings: soc: microchip: document PolarFire SoC's gpio interrupt mux
gpio: mpfs: Add interrupt support
soc: qcom: ubwc: add helpers to get programmable values
soc: qcom: ubwc: add helper to get min_acc length
firmware: qcom: scm: Register gunyah watchdog device
soc: qcom: socinfo: Add SoC ID for SA8650P
dt-bindings: arm: qcom,ids: Add SoC ID for SA8650P
firmware: qcom: scm: Allow QSEECOM on Mahua CRD
soc: qcom: wcnss: simplify allocation of req
soc: qcom: pd-mapper: Add support for Eliza
soc: qcom: aoss: compare against normalized cooling state
soc: qcom: llcc: fix v1 SB syndrome register offset
...
The HDP driver uses the generic GPIO chip API, but this configuration
may not be enabled.
Ensure it is enabled by selecting the appropriate option.
Fixes: 4bcff9c05b ("pinctrl: stm32: use new generic GPIO chip API")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
When a GPIO RIF configuration is in semaphore mode, and the semaphore
hasn't been taken before configuring the GPIO, the write operations
silently fail.
To avoid a silent fail when applying a pinctrl, if the pins that are
being configured are in semaphore mode, take the semaphore. Note that
there is no proper release of the RIF semaphore yet for pinctrl.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In stm32_pctl_probe(), hwspin_lock_request_specific() is called to
request a hwspinlock, but the acquired lock is not freed on multiple
error paths after this call. This causes resource leakage when the
function fails to initialize properly.
Use devm_hwspin_lock_request_specific() instead of
hwspin_lock_request_specific() to automatically manage the hwspinlock
resource lifecycle.
Fixes: 97cfb6cd34 ("pinctrl: stm32: protect configuration registers with a hwspinlock")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices in the stm32mp2xx family include an I/O synchronization
block on each pin that is used to fine tune and improve the I/O
timing margins of high speed synchronous interfaces.
It can be configured to provide independently for each pin:
- skew rate on input direction or latch delay on output direction;
- inversion of clock signals or re-sampling of data signals.
Add support for the generic properties:
- skew-delay-input-ps;
- skew-delay-output-ps.
Add support for the property 'st,io-sync' to configure clock
inversion or data re-sampling mode.
Show the new parameters on debugfs pinconf-pins.
Enable it for the stm32mp257 pinctrl driver.
Co-developed-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Co-developed-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change type of variable to avoid keeping the bool return value in
a variable of u32 type.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to acquire a spinlock to only read a register for
debugfs reporting.
Drop such useless spinlock save and restore.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use C bit-field to keep the backup of the pin status, instead of
explicitly handling the bit-field through shift and mask of a u32
container.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reduce the number of parameters of the function by moving inside
the function the decoding of the field 'config'.
While there:
- change the type of 'param' to 'unsigned int' to handle the extra
values not in 'enum pin_config_param';
- change the type of 'arg' to 'u32' to avoid additional conversions
and align to 'u32' the corresponding param of __stm32_gpio_set().
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"We have GPIO awareness in the pin control core and an interesting
AAEON driver.
Core changes:
- Allow pins to be identified/marked as GPIO mode with a special
callback.
The pin controller core is now "aware" if a pin is in GPIO mode if
the callback is implemented in the driver, and can thus be marked
as "strict", i.e. disallowing simultaneous use of a line as GPIO
and another function such as I2C.
This is enabled in the Qualcomm TLMM driver and also implemeted
from day 1 in the new Broadcom STB driver
- Rename the pin config option PIN_CONFIG_OUTPUT to PIN_CONFIG_LEVEL
to better describe what the config is doing, as well as making it
more intuitive what shall be returned when reading this property
New drivers:
- Qualcomm SDM660 LPASS LPI TLMM pin controller subdriver
- Qualcomm Glymur family pin controller driver
- Broadcom STB family pin controller driver
- Tegra186 pin controller driver
- AAEON UP pin controller support.
This is some special pin controller that works as an external
advanced line MUX and amplifier for signals from an Intel SoC. A
cooperative effort with the GPIO maintainer was needed to reach a
solution where we reuse code from the GPIO aggregator/forwarder
driver
- Renesas RZ/T2H and RZ/N2H pin controller support
- Axis ARTPEC-8 subdriver for the Samsung pin controller driver
Improvements:
- Output enable (OEN) support in the Renesas RZG2L driver
- Properly support bias pull up/down in the pinctrl-single driver
- Move over all GPIO portions using generic MMIO GPIO to the new
generic GPIO chip management which has a nice and separate API
- Proper DT bindings for some older Broadcom SoCs
- External GPIO (EGPIO) support in the Qualcomm SM8250
Deleted code:
- Dropped the now unused Samsung S3C24xx drivers"
* tag 'pinctrl-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: use more common syntax for compound literals
pinctrl: Simplify printks with pOF format
pinctrl: qcom: Add SDM660 LPASS LPI TLMM
dt-bindings: pinctrl: qcom: Add SDM660 LPI pinctrl
pinctrl: qcom: lpass-lpi: Add ability to use custom pin offsets
pinctrl: qcom: Add glymur pinctrl driver
dt-bindings: pinctrl: qcom: Add Glymur pinctrl
pinctrl: qcom: sm8250: Add egpio support
pinctrl: generic: rename PIN_CONFIG_OUTPUT to LEVEL
pinctrl: keembay: fix double free in keembay_build_functions()
pinctrl: spacemit: fix typo in PRI_TDI pin name
pinctrl: eswin: Fix regulator error check and Kconfig dependency
pinctrl: bcm: Add STB family pin controller driver
dt-bindings: pinctrl: Add support for Broadcom STB pin controller
pinctrl: qcom: make the pinmuxing strict
pinctrl: qcom: mark the `gpio` and `egpio` pins function as non-strict functions
pinctrl: qcom: add infrastructure for marking pin functions as GPIOs
pinctrl: allow to mark pin functions as requestable GPIOs
pinctrl: qcom: use generic pin function helpers
pinctrl: make struct pinfunction a pointer in struct function_desc
...
This generic pin config property is confusingly named so let's
rename it to make things clearer.
There are already drivers in the tree that use PIN_CONFIG_OUTPUT
to *read* the value of an output driven pin, which is a big
semantic confusion for the head: are we then reading the
setting of the output or the actual value/level that is put
out on the pin?
We already have PIN_CONFIG_OUTPUT_ENABLE that turns on driver
buffers for output, so this can by logical conclusion only
drive the voltage level if it should be any different.
But if we read the pin, are we then reading the *setting* of
the output value or the *actual* value we can see on the
line?
If the pin has not first been set into output mode with
PIN_CONFIG_OUTPUT_ENABLE, but is instead in some input mode
or tristate, what will reading this property actually
return?
Reading the current users reading this property it is clear
that what we read is the logical level of the pin as 0 or 1
depending on if it is low or high.
Rename it to PIN_CONFIG_LEVEL so it is crystal clear that
we set or read the voltage level of the pin and nothing else.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The commit acaa037970 ("pinctrl: stm32: Implement .get_direction
gpio_chip callback") exported the function stm32_pmx_get_mode()
and the struct stm32_gpio_bank, but these were never used outside
the file that defines them.
Declare the function as static, drop it from the include file and
drop also the struct, not anymore visible outside the file.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Link: https://lore.kernel.org/20250610143042.295376-2-antonio.borneo@foss.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
