Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Allow TLP Processing Hints to be enabled for RCiEPs (George Abraham
P)
- Enable AtomicOps only if we know the Root Port supports them (Gerd
Bayer)
- Don't enable AtomicOps for RCiEPs since none of them need Atomic
Ops and we can't tell whether the Root Complex would support them
(Gerd Bayer)
- Leave Precision Time Measurement disabled until a driver enables it
to avoid PCIe errors (Mika Westerberg)
- Make pci_set_vga_state() fail if bridge doesn't support VGA
routing, i.e., PCI_BRIDGE_CTL_VGA is not writable, and return
errors to vga_get() callers including userspace via
/dev/vga_arbiter (Simon Richter)
- Validate max-link-speed from DT in j721e, brcmstb, mediatek-gen3,
rzg3s drivers (where the actual controller constraints are known),
and remove validation from the generic OF DT accessor (Hans Zhang)
- Remove pc110pad driver (no longer useful after 486 CPU support
removed) and no_pci_devices() (pc110pad was the last user) (Dmitry
Torokhov, Heiner Kallweit)
Resource management:
- Prevent assigning space to unimplemented bridge windows; previously
we mistakenly assumed prefetchable window existed and assigned
space and put a BAR there (Ahmed Naseef)
- Avoid shrinking bridge windows to fit in the initial Root Port
window; fixes one problem with devices with large BARs connected
via switches, e.g., Thunderbolt (Ilpo Järvinen)
- Pass full extent of empty space, not just the aligned space, to
resource_alignf callback so free space before the requested
alignment can be used (Ilpo Järvinen)
- Place small resources before larger ones for better utilization of
address space (Ilpo Järvinen)
- Fix alignment calculation for resource size larger than align,
e.g., bridge windows larger than the 1MB required alignment (Ilpo
Järvinen)
Reset:
- Update slot handling so all ARI functions are treated as being in
the same slot. They're all reset by Secondary Bus Reset, but
previously drivers of ARI functions that appeared to be on a
non-zero device weren't notified and fatal hardware errors could
result (Keith Busch)
- Make sysfs reset_subordinate hotplug safe to avoid spurious hotplug
events (Keith Busch)
- Hide Secondary Bus Reset ('bus') from sysfs reset_methods if masked
by CXL because it has no effect (Vidya Sagar)
- Avoid FLR for AMD NPU device, where it causes the device to hang
(Lizhi Hou)
Error handling:
- Clear only error bits in PCIe Device Status to avoid accidentally
clearing Emergency Power Reduction Detected (Shuai Xue)
- Check for AER errors even in devices without drivers (Lukas Wunner)
- Initialize ratelimit info so DPC and EDR paths log AER error
information (Kuppuswamy Sathyanarayanan)
Power control:
- Add UPD720201/UPD720202 USB 3.0 xHCI Host Controller .compatible so
generic pwrctrl driver can control it (Neil Armstrong)
Hotplug:
- Set LED_HW_PLUGGABLE for NPEM hotplug-capable ports so LED core
doesn't complain when setting brightness fails because the endpoint
is gone (Richard Cheng)
Peer-to-peer DMA:
- Allow wildcards in list of host bridges that support peer-to-peer
DMA between hierarchy domains and add all Google SoCs (Jacob
Moroni)
Endpoint framework:
- Advertise dynamic inbound mapping support in pci-epf-test and
update host pci_endpoint_test to skip doorbell testing if not
advertised by endpoint (Koichiro Den)
- Return 0, not remaining timeout, when MHI eDMA ops complete so
mhi_ep_ring_add_element() doesn't interpret non-zero as failure
(Daniel Hodges)
- Remove vntb and ntb duplicate resource teardown that leads to oops
when .allow_link() fails or .drop_link() is called (Koichiro Den)
- Disable vntb delayed work before clearing BAR mappings and
doorbells to avoid oops caused by doing the work after resources
have been torn down (Koichiro Den)
- Add a way to describe reserved subregions within BARs, e.g.,
platform-owned fixed register windows, and use it for the RK3588
BAR4 DMA ctrl window (Koichiro Den)
- Add BAR_DISABLED for BARs that will never be available to an EPF
driver, and change some BAR_RESERVED annotations to BAR_DISABLED
(Niklas Cassel)
- Add NTB .get_dma_dev() callback for cases where DMA API requires a
different device, e.g., vNTB devices (Koichiro Den)
- Add reserved region types for MSI-X Table and PBA so Endpoint
controllers can them as describe hardware-owned regions in a
BAR_RESERVED BAR (Manikanta Maddireddy)
- Make Tegra194/234 BAR0 programmable and remove 1MB size limit
(Manikanta Maddireddy)
- Expose Tegra BAR2 (MSI-X) and BAR4 (DMA) as 64-bit BAR_RESERVED
(Manikanta Maddireddy)
- Add Tegra194 and Tegra234 device table entries to pci_endpoint_test
(Manikanta Maddireddy)
- Skip the BAR subrange selftest if there are not enough inbound
window resources to run the test (Christian Bruel)
New native PCIe controller drivers:
- Add DT binding and driver for Andes QiLai SoC PCIe host controller
(Randolph Lin)
- Add DT binding and driver for ESWIN PCIe Root Complex (Senchuan
Zhang)
Baikal T-1 PCIe controller driver:
- Remove driver since it never quite became usable (Andy Shevchenko)
Cadence PCIe controller driver:
- Implement byte/word config reads with dword (32-bit) reads because
some Cadence controllers don't support sub-dword accesses (Aksh
Garg)
CIX Sky1 PCIe controller driver:
- Add 'power-domains' to DT binding for SCMI power domain (Gary Yang)
Freescale i.MX6 PCIe controller driver:
- Add i.MX94 and i.MX943 to fsl,imx6q-pcie-ep DT binding (Richard
Zhu)
- Delay instead of polling for L2/L3 Ready after PME_Turn_off when
suspending i.MX6SX because LTSSM registers are inaccessible
(Richard Zhu)
- Separate PERST# assertion (for resetting endpoints) from core reset
(for resetting the RC itself) to prepare for new DTs with PERST#
GPIO in per-Root Port nodes (Sherry Sun)
- Retain Root Port MSI capability on i.MX7D, i.MX8MM, and i.MX8MQ so
MSI from downstream devices will work (Richard Zhu)
- Fix i.MX95 reference clock source selection when internal refclk is
used (Franz Schnyder)
Freescale Layerscape PCIe controller driver:
- Allow building as a removable module (Sascha Hauer)
MediaTek PCIe Gen3 controller driver:
- Use dev_err_probe() to simplify error paths and make deferred probe
messages visible in /sys/kernel/debug/devices_deferred (Chen-Yu
Tsai)
- Power off device if setup fails (Chen-Yu Tsai)
- Integrate new pwrctrl API to enable power control for WiFi/BT
adapters on mainboard or in PCIe or M.2 slots (Chen-Yu Tsai)
NVIDIA Tegra194 PCIe controller driver:
- Poll less aggressively and non-atomically for PME_TO_Ack during
transition to L2 (Vidya Sagar)
- Disable LTSSM after transition to Detect on surprise link down to
stop toggling between Polling and Detect (Manikanta Maddireddy)
- Don't force the device into the D0 state before L2 when suspending
or shutting down the controller (Vidya Sagar)
- Disable PERST# IRQ only in Endpoint mode because it's not
registered in Root Port mode (Manikanta Maddireddy)
- Handle 'nvidia,refclk-select' as optional (Vidya Sagar)
- Disable direct speed change in Endpoint mode so link speed change
is controlled by the host (Vidya Sagar)
- Set LTR values before link up to avoid bogus LTR messages with 0
latency (Vidya Sagar)
- Allow system suspend when the Endpoint link is down (Vidya Sagar)
- Use DWC IP core version, not Tegra custom values, to avoid DWC core
version check warnings (Manikanta Maddireddy)
- Apply ECRC workaround to devices based on DesignWare 5.00a as well
as 4.90a (Manikanta Maddireddy)
- Disable PM Substate L1.2 in Endpoint mode to work around Tegra234
erratum (Vidya Sagar)
- Delay post-PERST# cleanup until core is powered on to avoid CBB
timeout (Manikanta Maddireddy)
- Assert CLKREQ# so switches that forward it to their downstream side
can bring up those links successfully (Vidya Sagar)
- Calibrate pipe to UPHY for Endpoint mode to reset stale PLL state
from any previous bad link state (Vidya Sagar)
- Remove IRQF_ONESHOT flag from Endpoint interrupt registration so
DMA driver and Endpoint controller driver can share the interrupt
line (Vidya Sagar)
- Enable DMA interrupt to support DMA in both Root Port and Endpoint
modes (Vidya Sagar)
- Enable hardware link retraining after link goes down in Endpoint
mode (Vidya Sagar)
- Add DT binding and driver support for core clock monitoring (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Advertise 'Hot-Plug Capable' and set 'No Command Completed Support'
since Qcom Root Ports support hotplug events like DL_Up/Down and
can accept writes to Slot Control without delays between writes
(Krishna Chaitanya Chundru)
Renesas R-Car PCIe controller driver:
- Mark Endpoint BAR0 and BAR2 as Resizable (Koichiro Den)
- Reduce EPC BAR alignment requirement to 4K (Koichiro Den)
Renesas RZ/G3S PCIe controller driver:
- Add RZ/G3E to DT binding and to driver (John Madieu)
- Assert (not deassert) resets in probe error path (John Madieu)
- Assert resets in suspend path in reverse order they were deasserted
during probe (John Madieu)
- Rework inbound window algorithm to prevent mapping more than
intended region and enforce alignment on size, to prepare for
RZ/G3E support (John Madieu)
Rockchip DesignWare PCIe controller driver:
- Add tracepoints for PCIe controller LTSSM transitions and link rate
changes (Shawn Lin)
- Trace LTSSM events collected by the dw-rockchip debug FIFO (Shawn
Lin)
SOPHGO PCIe controller driver:
- Disable ASPM L0s and L1 on Sophgo 2042 PCIe Root Ports that
advertise support for them (Yao Zi)
Synopsys DesignWare PCIe controller driver:
- Continue with system suspend even if an Endpoint doesn't respond
with PME_TO_Ack message (Manivannan Sadhasivam)
- Set Endpoint MSI-X Table Size in the correct function of a
multi-function device when configuring MSI-X, not in Function 0
(Aksh Garg)
- Set Max Link Width and Max Link Speed for all functions of a
multi-function device, not just Function 0 (Aksh Garg)
- Expose PCIe event counters in groups 5-7 in debugfs (Hans Zhang)
Miscellaneous:
- Warn only once about invalid ACS kernel parameter format (Richard
Cheng)
- Suppress FW_BUG warning when writing sysfs 'numa_node' with the
current value (Li RongQing)
- Drop redundant 'depends on PCI' from Kconfig (Julian Braha)"
* tag 'pci-v7.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (165 commits)
PCI/P2PDMA: Add Google SoCs to the P2P DMA host bridge list
PCI/P2PDMA: Allow wildcard Device IDs in host bridge list
PCI: sg2042: Avoid L0s and L1 on Sophgo 2042 PCIe Root Ports
PCI: cadence: Add flags for disabling ASPM capability for broken Root Ports
PCI: tegra194: Add core monitor clock support
dt-bindings: PCI: tegra194: Add monitor clock support
PCI: tegra194: Enable hardware hot reset mode in Endpoint mode
PCI: tegra194: Enable DMA interrupt
PCI: tegra194: Remove IRQF_ONESHOT flag during Endpoint interrupt registration
PCI: tegra194: Calibrate pipe to UPHY for Endpoint mode
PCI: tegra194: Assert CLKREQ# explicitly by default
PCI: tegra194: Fix CBB timeout caused by DBI access before core power-on
PCI: tegra194: Disable L1.2 capability of Tegra234 EP
PCI: dwc: Apply ECRC workaround to DesignWare 5.00a as well
PCI: tegra194: Use DWC IP core version
PCI: tegra194: Free up Endpoint resources during remove()
PCI: tegra194: Allow system suspend when the Endpoint link is not up
PCI: tegra194: Set LTR message request before PCIe link up in Endpoint mode
PCI: tegra194: Disable direct speed change for Endpoint mode
PCI: tegra194: Use devm_gpiod_get_optional() to parse "nvidia,refclk-select"
...
Disable the delayed work before clearing BAR mappings and doorbells to
avoid running the handler after resources have been torn down.
Unable to handle kernel paging request at virtual address ffff800083f46004
[...]
Internal error: Oops: 0000000096000007 [#1] SMP
[...]
Call trace:
epf_ntb_cmd_handler+0x54/0x200 [pci_epf_vntb] (P)
process_one_work+0x154/0x3b0
worker_thread+0x2c8/0x400
kthread+0x148/0x210
ret_from_fork+0x10/0x20
Fixes: e35f56bb03 ("PCI: endpoint: Support NTB transfer between RC and EP")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260226084142.2226875-4-den@valinux.co.jp
epf_ntb_epc_destroy() duplicates the teardown that the caller is
supposed to do later. This leads to an oops when .allow_link fails or
when .drop_link is performed. Remove the helper.
Also drop pci_epc_put(). EPC device refcounting is tied to configfs EPC
group lifetime, and pci_epc_put() in the .drop_link path is sufficient.
Fixes: 8b821cf761 ("PCI: endpoint: Add EP function driver to provide NTB functionality")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260226084142.2226875-3-den@valinux.co.jp
epf_ntb_epc_destroy() duplicates the teardown that the caller is
supposed to perform later. This leads to an oops when .allow_link fails
or when .drop_link is performed. The following is an example oops of the
former case:
Unable to handle kernel paging request at virtual address dead000000000108
[...]
[dead000000000108] address between user and kernel address ranges
Internal error: Oops: 0000000096000044 [#1] SMP
[...]
Call trace:
pci_epc_remove_epf+0x78/0xe0 (P)
pci_primary_epc_epf_link+0x88/0xa8
configfs_symlink+0x1f4/0x5a0
vfs_symlink+0x134/0x1d8
do_symlinkat+0x88/0x138
__arm64_sys_symlinkat+0x74/0xe0
[...]
Remove the helper, and drop pci_epc_put(). EPC device refcounting is
tied to the configfs EPC group lifetime, and pci_epc_put() in the
.drop_link path is sufficient.
Fixes: e35f56bb03 ("PCI: endpoint: Support NTB transfer between RC and EP")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260226084142.2226875-2-den@valinux.co.jp
pci_epf_mhi_edma_read() and pci_epf_mhi_edma_write() start DMA
operations and wait for completion with a timeout.
On successful completion, they previously returned the remaining
timeout, which callers may treat as an error. In particular,
mhi_ep_ring_add_element(), which calls pci_epf_mhi_edma_write() via
mhi_cntrl->write_sync(), interprets any non-zero return value as
failure.
Return 0 on success instead of the remaining timeout to prevent
mhi_ep_ring_add_element() from treating successful completion as an
error.
Fixes: 7b99aaadda ("PCI: epf-mhi: Add eDMA support")
Signed-off-by: Daniel Hodges <git@danielhodges.dev>
[mani: changed commit log as per https://lore.kernel.org/linux-pci/20260227191510.GA3904799@bhelgaas]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260206200529.10784-1-git@danielhodges.dev
Follow common kernel idioms for indices derived from configfs attributes
and suppress Smatch warnings:
epf_ntb_mw1_show() warn: potential spectre issue 'ntb->mws_size' [r]
epf_ntb_mw1_store() warn: potential spectre issue 'ntb->mws_size' [w]
Also fix the error message for out-of-range MW indices and %lld format
for unsigned values.
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260105075606.1253697-1-den@valinux.co.jp
'struct configfs_item_operations' and 'configfs_group_operations' are not
modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
27503 12184 256 39943 9c07 drivers/pci/endpoint/pci-ep-cfs.o
After:
=====
text data bss dec hex filename
27855 11832 256 39943 9c07 drivers/pci/endpoint/pci-ep-cfs.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/f1f05f1c10c6caf37dd620fa12f508c53536996b.1765705512.git.christophe.jaillet@wanadoo.fr
The doorbell test requires the EPC driver to support dynamic inbound
mapping so the host can map the doorbell target address into a BAR
aperture.
Expose epc_features->dynamic_inbound_mapping via a new
CAP_DYNAMIC_INBOUND_MAPPING bit in the pci-epf-test capability register,
so the host-side pci_endpoint_test driver can detect missing support and
return -EOPNOTSUPP instead of running the test fruitlessly.
Suggested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260215150334.3391943-2-den@valinux.co.jp
pci_epf_alloc_doorbell() stores the allocated doorbell message array in
epf->db_msg/epf->num_db before requesting MSI vectors. If MSI allocation
fails, the array is freed but the EPF state may still point to freed
memory.
Clear epf->db_msg and epf->num_db on the MSI allocation failure path so
that later cleanup cannot double-free the array and callers can retry
allocation.
Also return -EBUSY when doorbells have already been allocated to prevent
leaking or overwriting an existing allocation.
Fixes: 1c3b002c6b ("PCI: endpoint: Add RC-to-EP doorbell support using platform MSI controller")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260217063856.3759713-4-den@valinux.co.jp
pci_epf_test_doorbell_cleanup() unconditionally calls free_irq() for the
doorbell virq, which can trigger "Trying to free already-free IRQ"
warnings when the IRQ was never requested or when request_threaded_irq()
failed.
Move free_irq() out of pci_epf_test_doorbell_cleanup() and invoke it
only after a successful request, so that free_irq() is not called for
an unrequested IRQ.
Fixes: eff0c286aa ("PCI: endpoint: pci-epf-test: Add doorbell test support")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260217063856.3759713-3-den@valinux.co.jp
epf_ntb_db_bar_init_msi_doorbell() requests ntb->db_count doorbell IRQs
and then performs additional MSI doorbell setup that may still fail.
The error path unwinds the requested IRQs, but it uses a loop variable
that is reused later in the function. When a later step fails, the
unwind can run with an unexpected index value and leave some IRQs
requested.
Track the number of successfully requested IRQs separately and use that
counter for the unwind so all previously requested IRQs are freed on
failure.
Fixes: dc693d6066 ("PCI: endpoint: pci-epf-vntb: Add MSI doorbell support")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260217063856.3759713-2-den@valinux.co.jp
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
- Extend PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() to return a
pointer to the preceding Capability (Qiang Yu)
- Add dw_pcie_remove_capability() and dw_pcie_remove_ext_capability() to
remove Capabilities that are advertised but not fully implemented (Qiang
Yu)
- Remove MSI and MSI-X Capabilities for DWC controllers in platforms that
can't support them, so we automatically fall back to INTx (Qiang Yu)
- Remove MSI-X and DPC Capabilities for Qualcomm platforms that advertise
but don't support them (Qiang Yu)
- Remove duplicate dw_pcie_ep_hide_ext_capability() function and replace
with dw_pcie_remove_ext_capability() (Qiang Yu)
- Add ASPM L1.1 and L1.2 Substates context to debugfs ltssm_status for
drivers that support this (Shawn Lin)
- Skip PME_Turn_Off broadcast and L2/L3 transition during suspend if link
is not up to avoid an unnecessary timeout (Manivannan Sadhasivam)
- Revert dw-rockchip, qcom, and DWC core changes that used link-up IRQs to
trigger enumeration instead of waiting for link to be up because the PCI
core doesn't allocate bus number space for hierarchies that might be
attached (Niklas Cassel)
- Make endpoint iATU entry for MSI permanent instead of programming it
dynamically, which is slow and racy with respect to other concurrent
traffic, e.g., eDMA (Koichiro Den)
- Use iMSI-RX MSI target address when possible to fix endpoints using
32-bit MSI (Shawn Lin)
- Make dw_pcie_ltssm_status_string() available and use it for logging
errors in dw_pcie_wait_for_link() (Manivannan Sadhasivam)
- Return -ENODEV when dw_pcie_wait_for_link() finds no devices, -EIO for
device present but inactive, -ETIMEDOUT for other failures, so callers
can handle these cases differently (Manivannan Sadhasivam)
- Allow DWC host controller driver probe to continue if device is not found
or found but inactive; only fail when there's an error with the link
(Manivannan Sadhasivam)
- For controllers like NXP i.MX6QP and i.MX7D, where LTSSM registers are
not accessible after PME_Turn_Off, simply wait 10ms instead of polling
for L2/L3 Ready (Richard Zhu)
- Use multiple iATU entries to map large bridge windows and DMA ranges when
necessary instead of failing (Samuel Holland)
- Rename struct dw_pcie_rp.has_msi_ctrl to .use_imsi_rx for clarity (Qiang
Yu)
- Add EPC dynamic_inbound_mapping feature bit for Endpoint Controllers that
can update BAR inbound address translation without requiring EPF driver
to clear/reset the BAR first, and advertise it for DWC-based Endpoints
(Koichiro Den)
- Add EPC subrange_mapping feature bit for Endpoint Controllers that can
map multiple independent inbound regions in a single BAR, implement
subrange mapping, advertise it for DWC-based Endpoints, and add Endpoint
selftests for it (Koichiro Den)
- Allow overriding default BAR sizes for pci-epf-test (Niklas Cassel)
- Make resizable BARs work for Endpoint multi-PF configurations; previously
it only worked for PF 0 (Aksh Garg)
- Fix Endpoint non-PF 0 support for BAR configuration, ATU mappings, and
Address Match Mode (Aksh Garg)
- Fix issues with outbound iATU index assignment that caused iATU index to
be out of bounds (Niklas Cassel)
- Clean up iATU index tracking to be consistent (Niklas Cassel)
- Set up iATU when ECAM is enabled; previously IO and MEM outbound windows
weren't programmed, and ECAM-related iATU entries weren't restored after
suspend/resume, so config accesses failed (Krishna Chaitanya Chundru)
* pci/controller/dwc:
PCI: dwc: Fix missing iATU setup when ECAM is enabled
PCI: dwc: Clean up iATU index usage in dw_pcie_iatu_setup()
PCI: dwc: Fix msg_atu_index assignment
PCI: dwc: ep: Add comment explaining controller level PTM access in multi PF setup
PCI: dwc: ep: Add per-PF BAR and inbound ATU mapping support
PCI: dwc: ep: Fix resizable BAR support for multi-PF configurations
PCI: endpoint: pci-epf-test: Allow overriding default BAR sizes
selftests: pci_endpoint: Add BAR subrange mapping test case
misc: pci_endpoint_test: Add BAR subrange mapping test case
PCI: endpoint: pci-epf-test: Add BAR subrange mapping test support
Documentation: PCI: endpoint: Clarify pci_epc_set_bar() usage
PCI: dwc: ep: Support BAR subrange inbound mapping via Address Match Mode iATU
PCI: dwc: Advertise dynamic inbound mapping support
PCI: endpoint: Add BAR subrange mapping support
PCI: endpoint: Add dynamic_inbound_mapping EPC feature
PCI: dwc: Rename dw_pcie_rp::has_msi_ctrl to dw_pcie_rp::use_imsi_rx for clarity
PCI: dwc: Fix grammar and formatting for comment in dw_pcie_remove_ext_capability()
PCI: dwc: Use multiple iATU windows for mapping large bridge windows and DMA ranges
PCI: dwc: Remove duplicate dw_pcie_ep_hide_ext_capability() function
PCI: dwc: Skip waiting for L2/L3 Ready if dw_pcie_rp::skip_l23_wait is true
PCI: dwc: Fail dw_pcie_host_init() if dw_pcie_wait_for_link() returns -ETIMEDOUT
PCI: dwc: Rework the error print of dw_pcie_wait_for_link()
PCI: dwc: Rename and move ltssm_status_string() to pcie-designware.c
PCI: dwc: Return -EIO from dw_pcie_wait_for_link() if device is not active
PCI: dwc: Return -ENODEV from dw_pcie_wait_for_link() if device is not found
PCI: dwc: Use cfg0_base as iMSI-RX target address to support 32-bit MSI devices
PCI: dwc: ep: Cache MSI outbound iATU mapping
Revert "PCI: dwc: Don't wait for link up if driver can detect Link Up event"
Revert "PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt"
Revert "PCI: qcom: Enable MSI interrupts together with Link up if 'Global IRQ' is supported"
Revert "PCI: qcom: Don't wait for link if we can detect Link Up"
Revert "PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ"
Revert "PCI: dw-rockchip: Don't wait for link since we can detect Link Up"
PCI: dwc: Skip PME_Turn_Off broadcast and L2/L3 transition during suspend if link is not up
PCI: dw-rockchip: Change get_ltssm() to provide L1 Substates info
PCI: dwc: Add L1 Substates context to ltssm_status of debugfs
PCI: qcom: Remove DPC Extended Capability
PCI: qcom: Remove MSI-X Capability for Root Ports
PCI: dwc: Remove MSI/MSIX capability for Root Port if iMSI-RX is used as MSI controller
PCI: dwc: Add new APIs to remove standard and extended Capability
PCI: Add preceding capability position support in PCI_FIND_NEXT_*_CAP macros
