Add the device tree of the evaluation board of the EyeQ6Lplus SoC.
The board comes with 2GB of RAM and an SPI NAND connected to the octoSPI
controller The UART of the SoC is used as the serial console.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the device tree include files for the EyeQ6Lplus system on chip
from Mobileye.
Those files provide the initial support of the SoC:
* The I6500 CPU and GIC interrupt controller.
* The OLB ("Other Logic Block") providing clocks, resets and pin controls.
* One UART.
* One GPIO controller.
* Two SPI controllers, one in host mode and one in target mode.
* One octoSPI flash controller.
* Two I2C controllers.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Loongson64g is Loongson 3A4000, whose UART controller is compatible with
Loongson 2K1500, which is NS16550A-compatible with an additional
fractional frequency divisor register.
Update the compatible strings to reflect this, so that 3A4000 can
benefit from the fractional frequency divisor provided by loongson-uart.
This is required on some devices, otherwise their UART can't work at
some high baud rates, e.g., 115200.
Tested on Loongson-LS3A4000-7A1000-NUC-SE with a 25MHz UART clock.
Without fractional frequency divisor, the actual baud rate was 111607
(25MHz / 16 / 14, measured value: 111545) and some USB-to-UART
converters couldn't work with it at all. With fractional frequency
divisor, the measured baud rate becomes 115207, which is quite accurate.
Signed-off-by: Rong Zhang <rongrong@oss.cipunited.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add PCIe based on EN7528 PCIe driver, also add two MT76 wifi devices
to SmartFiber XP8421-B.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (28 commits)
Revert "clk: microchip: core: allow driver to be compiled with COMPILE_TEST"
Revert "clk: microchip: fix typo in reference to a config option"
MIPS: Implement ARCH_HAS_CC_CAN_LINK
MIPS: rb532: Fix MMIO UART resource registration
MIPS: Work around LLVM bug when gp is used as global register variable
MIPS: Loongson64: env: Fixup serial clock-frequency when using LEFI
MIPS: Loongson2ef: Use pcibios_align_resource() to block io range
MIPS: Loongson2ef: Register PCI controller in early stage
clk: microchip: fix typo in reference to a config option
MIPS: Loongson64: dts: fix phy-related definition of LS7A GMAC
clk: microchip: core: allow driver to be compiled with COMPILE_TEST
MIPS: drop unused pic32.h header
watchdog: pic32-wdt: update include to use pic32.h from platform_data
watchdog: pic32-dmt: update include to use pic32.h from platform_data
serial: pic32_uart: update include to use pic32.h from platform_data
rtc: pic32: update include to use pic32.h from platform_data
pinctrl: pic32: update include to use pic32.h from platform_data
mmc: sdhci-pic32: update include to use pic32.h from platform_data
irqchip/irq-pic32-evic: update include to use pic32.h from platform_data
clk: microchip: core: update include to use pic32.h from platform_data
...
R_MIPS_PC32 is a GNU extension, its definition is available in glibc
only since 2.39 (released in 2024), and not available in musl libc yet.
Provide our own definition for R_MIPS_PC32 and use it if necessary to
fix relocs tool building on musl and older glibc systems.
Fixes: ff79d31eb5 ("mips: Add support for PC32 relocations in vmlinux")
Signed-off-by: Yao Zi <me@ziyao.cc>
Link: https://patch.msgid.link/20260202041610.61389-1-me@ziyao.cc
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Currently the LS7A GMAC device tree node lacks a proper phy-handle
property pointing to the PHY node.
In addition, the phy-mode property specifies "rgmii" without any
internal delay information, which means the board trace needs to add 2ns
delay to the RGMII data lines; but that isn't known to happen on any
Loongson board. The ACPI-based initialization codepath, which is used on
LoongArch-based 3A5000 + 7A1000 hardwares, specifies "rgmii-id" phy
mode, which should be the one we are using.
Add the lacking phy-handle property and set proper phy-mode.
Tested on a LS3A4000_7A1000_NUC_BOARD_V2.1 board with YT8521S PHY.
Signed-off-by: Icenowy Zheng <zhengxingda@iscas.ac.cn>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
MIPS supports PC32 relocations like most other architectures, which will
be used by kallsyms to make its symbol references visible to the linker.
Given that these are place-relative, they can be ignored by the 'relocs'
tool, just like other PC type relocations.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://patch.msgid.link/20260116093359.2442297-5-ardb+git@google.com
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Commit 41528ba6af ("MIPS: DTS: Only build subdir of current platform")
broke building of all DTBs when CONFIG_OF_ALL_DTBS is enabled unless all
the various kconfig options were also enabled. The only effect that commit
had was getting rid of some harmless build lines such as:
AR arch/mips/boot/dts/mti/built-in.a
Those lines were part of the built-in DTB support. Since commit
04e4ec98e4 ("MIPS: migrate to generic rule for built-in DTBs"), how the
built-in DTBs are handled has changed and those lines are no longer
generated, so revert to the prior behavior.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In fact, it is a multi-threaded MIPS34Kc, not a single-threaded MIPS24Kc.
Fixes: 0ec4887009 ("mips: dts: Add EcoNet DTS with EN751221 and SmartFiber XP8421-B board")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Since the current bootloader for Loongson-1 does not support FDT,
introduce CONFIG_BUILTIN_DTB_NAME to enable a built-in DTB.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a device tree for Smartloong-1C board, supporting CPU, clock, INTC,
UART, Ethernet, GPIO, USB host, RTC, watchdog, DMA, and NAND.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a device tree for LS1B-DEMO board, supporting CPU, clock, INTC,
UART, Ethernet, GPIO, USB host, RTC, watchdog, DMA, NAND, and AC97.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: stp@e100bb0 (lantiq,gpio-stp-xway): $nodename:0: 'stp@e100bb0' does not match '^gpio@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
With the DT binding updated with 501be7cece ("dt-bindings:
memory-controller: Define fallback compatible") we need to define a
proper compatible string for the memory controller node(s).
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad937 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0 ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
