Merge branch 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm

Pull ARM updates from Russell King:

 - nommu updates from Afzal Mohammed cleaning up the vectors support

 - allow DMA memory "mapping" for nommu Benjamin Gaignard

 - fixing a correctness issue with R_ARM_PREL31 relocations in the
   module linker

 - add strlen() prototype for the decompressor

 - support for DEBUG_VIRTUAL from Florian Fainelli

 - adjusting memory bounds after memory reservations have been
   registered

 - unipher cache handling updates from Masahiro Yamada

 - initrd and Thumb Kconfig cleanups

* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
  ARM: mm: round the initrd reservation to page boundaries
  ARM: mm: clean up initrd initialisation
  ARM: mm: move initrd init code out of arm_memblock_init()
  ARM: 8655/1: improve NOMMU definition of pgprot_*()
  ARM: 8654/1: decompressor: add strlen prototype
  ARM: 8652/1: cache-uniphier: clean up active way setup code
  ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
  ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
  ARM: 8649/2: nommu: remove Hivecs configuration is asm
  ARM: 8648/2: nommu: display vectors base
  ARM: 8647/2: nommu: dynamic exception base address setting
  ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
  ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
  ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
  ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
  ARM: 8639/1: Define KERNEL_START and KERNEL_END
  ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
  ARM: 8637/1: Adjust memory boundaries after reservations
  ARM: 8636/1: Cleanup sanity_check_meminfo
  ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
  ...

arch/arm/Kconfig

@@ -2,6 +2,7 @@ config ARM
 	bool
 	default y
 	select ARCH_CLOCKSOURCE_DATA
+	select ARCH_HAS_DEBUG_VIRTUAL
 	select ARCH_HAS_DEVMEM_IS_ALLOWED
 	select ARCH_HAS_ELF_RANDOMIZE
 	select ARCH_HAS_SET_MEMORY

arch/arm/Kconfig-nommu

@@ -34,8 +34,7 @@ config PROCESSOR_ID
 	  used instead of the auto-probing which utilizes the register.
 
 config REMAP_VECTORS_TO_RAM
-	bool 'Install vectors to the beginning of RAM' if DRAM_BASE
-	depends on DRAM_BASE
+	bool 'Install vectors to the beginning of RAM'
 	help
 	  The kernel needs to change the hardware exception vectors.
 	  In nommu mode, the hardware exception vectors are normally

arch/arm/boot/compressed/decompress.c

@@ -32,6 +32,7 @@ extern void error(char *);
 
 /* Not needed, but used in some headers pulled in by decompressors */
 extern char * strstr(const char * s1, const char *s2);
+extern size_t strlen(const char *s);
 
 #ifdef CONFIG_KERNEL_GZIP
 #include "../../../../lib/decompress_inflate.c"

arch/arm/common/mcpm_entry.c

@@ -144,7 +144,7 @@ extern unsigned long mcpm_entry_vectors[MAX_NR_CLUSTERS][MAX_CPUS_PER_CLUSTER];
 
 void mcpm_set_entry_vector(unsigned cpu, unsigned cluster, void *ptr)
 {
-	unsigned long val = ptr ? virt_to_phys(ptr) : 0;
+	unsigned long val = ptr ? __pa_symbol(ptr) : 0;
 	mcpm_entry_vectors[cluster][cpu] = val;
 	sync_cache_w(&mcpm_entry_vectors[cluster][cpu]);
 }
@@ -299,8 +299,8 @@ void mcpm_cpu_power_down(void)
 	 * the kernel as if the power_up method just had deasserted reset
 	 * on the CPU.
 	 */
-	phys_reset = (phys_reset_t)(unsigned long)virt_to_phys(cpu_reset);
-	phys_reset(virt_to_phys(mcpm_entry_point));
+	phys_reset = (phys_reset_t)(unsigned long)__pa_symbol(cpu_reset);
+	phys_reset(__pa_symbol(mcpm_entry_point));
 
 	/* should never get here */
 	BUG();
@@ -388,8 +388,8 @@ static int __init nocache_trampoline(unsigned long _arg)
 	__mcpm_outbound_leave_critical(cluster, CLUSTER_DOWN);
 	__mcpm_cpu_down(cpu, cluster);
 
-	phys_reset = (phys_reset_t)(unsigned long)virt_to_phys(cpu_reset);
-	phys_reset(virt_to_phys(mcpm_entry_point));
+	phys_reset = (phys_reset_t)(unsigned long)__pa_symbol(cpu_reset);
+	phys_reset(__pa_symbol(mcpm_entry_point));
 	BUG();
 }
 
@@ -449,7 +449,7 @@ int __init mcpm_sync_init(
 	sync_cache_w(&mcpm_sync);
 
 	if (power_up_setup) {
-		mcpm_power_up_setup_phys = virt_to_phys(power_up_setup);
+		mcpm_power_up_setup_phys = __pa_symbol(power_up_setup);
 		sync_cache_w(&mcpm_power_up_setup_phys);
 	}
 

arch/arm/include/asm/hardware/cache-uniphier.h

@@ -16,7 +16,7 @@
 #ifndef __CACHE_UNIPHIER_H
 #define __CACHE_UNIPHIER_H
 
-#include <linux/types.h>
+#include <linux/errno.h>
 
 #ifdef CONFIG_CACHE_UNIPHIER
 int uniphier_cache_init(void);

arch/arm/include/asm/memory.h

@@ -83,8 +83,15 @@
 #define IOREMAP_MAX_ORDER	24
 #endif
 
+#define VECTORS_BASE		UL(0xffff0000)
+
 #else /* CONFIG_MMU */
 
+#ifndef __ASSEMBLY__
+extern unsigned long vectors_base;
+#define VECTORS_BASE		vectors_base
+#endif
+
 /*
  * The limitation of user task size can grow up to the end of free ram region.
  * It is difficult to define and perhaps will never meet the original meaning
@@ -111,6 +118,13 @@
 
 #endif /* !CONFIG_MMU */
 
+#ifdef CONFIG_XIP_KERNEL
+#define KERNEL_START		_sdata
+#else
+#define KERNEL_START		_stext
+#endif
+#define KERNEL_END		_end
+
 /*
  * We fix the TCM memories max 32 KiB ITCM resp DTCM at these
  * locations
@@ -206,7 +220,7 @@ extern const void *__pv_table_begin, *__pv_table_end;
 	: "r" (x), "I" (__PV_BITS_31_24)		\
 	: "cc")
 
-static inline phys_addr_t __virt_to_phys(unsigned long x)
+static inline phys_addr_t __virt_to_phys_nodebug(unsigned long x)
 {
 	phys_addr_t t;
 
@@ -238,7 +252,7 @@ static inline unsigned long __phys_to_virt(phys_addr_t x)
 #define PHYS_OFFSET	PLAT_PHYS_OFFSET
 #define PHYS_PFN_OFFSET	((unsigned long)(PHYS_OFFSET >> PAGE_SHIFT))
 
-static inline phys_addr_t __virt_to_phys(unsigned long x)
+static inline phys_addr_t __virt_to_phys_nodebug(unsigned long x)
 {
 	return (phys_addr_t)x - PAGE_OFFSET + PHYS_OFFSET;
 }
@@ -254,6 +268,16 @@ static inline unsigned long __phys_to_virt(phys_addr_t x)
 	((((unsigned long)(kaddr) - PAGE_OFFSET) >> PAGE_SHIFT) + \
 	 PHYS_PFN_OFFSET)
 
+#define __pa_symbol_nodebug(x)	__virt_to_phys_nodebug((x))
+
+#ifdef CONFIG_DEBUG_VIRTUAL
+extern phys_addr_t __virt_to_phys(unsigned long x);
+extern phys_addr_t __phys_addr_symbol(unsigned long x);
+#else
+#define __virt_to_phys(x)	__virt_to_phys_nodebug(x)
+#define __phys_addr_symbol(x)	__pa_symbol_nodebug(x)
+#endif
+
 /*
  * These are *only* valid on the kernel direct mapped RAM memory.
  * Note: Drivers should NOT use these.  They are the wrong
@@ -276,6 +300,7 @@ static inline void *phys_to_virt(phys_addr_t x)
  * Drivers should NOT use these either.
  */
 #define __pa(x)			__virt_to_phys((unsigned long)(x))
+#define __pa_symbol(x)		__phys_addr_symbol(RELOC_HIDE((unsigned long)(x), 0))
 #define __va(x)			((void *)__phys_to_virt((phys_addr_t)(x)))
 #define pfn_to_kaddr(pfn)	__va((phys_addr_t)(pfn) << PAGE_SHIFT)
 

arch/arm/include/asm/pgtable-nommu.h

@@ -63,9 +63,9 @@ typedef pte_t *pte_addr_t;
 /*
  * Mark the prot value as uncacheable and unbufferable.
  */
-#define pgprot_noncached(prot)	__pgprot(0)
-#define pgprot_writecombine(prot) __pgprot(0)
-#define pgprot_dmacoherent(prot) __pgprot(0)
+#define pgprot_noncached(prot)	(prot)
+#define pgprot_writecombine(prot) (prot)
+#define pgprot_dmacoherent(prot) (prot)
 
 
 /*

arch/arm/kernel/head-nommu.S

@@ -151,11 +151,6 @@ __after_proc_init:
 #endif
 #ifdef CONFIG_CPU_ICACHE_DISABLE
 	bic	r0, r0, #CR_I
-#endif
-#ifdef CONFIG_CPU_HIGH_VECTOR
-	orr	r0, r0, #CR_V
-#else
-	bic	r0, r0, #CR_V
 #endif
 	mcr	p15, 0, r0, c1, c0, 0		@ write control reg
 #elif defined (CONFIG_CPU_V7M)

arch/arm/kernel/module.c

@@ -155,8 +155,17 @@ apply_relocate(Elf32_Shdr *sechdrs, const char *strtab, unsigned int symindex,
 		       break;
 
 		case R_ARM_PREL31:
-			offset = *(u32 *)loc + sym->st_value - loc;
-			*(u32 *)loc = offset & 0x7fffffff;
+			offset = (*(s32 *)loc << 1) >> 1; /* sign extend */
+			offset += sym->st_value - loc;
+			if (offset >= 0x40000000 || offset < -0x40000000) {
+				pr_err("%s: section %u reloc %u sym '%s': relocation %u out of range (%#lx -> %#x)\n",
+				       module->name, relindex, i, symname,
+				       ELF32_R_TYPE(rel->r_info), loc,
+				       sym->st_value);
+				return -ENOEXEC;
+			}
+			*(u32 *)loc &= 0x80000000;
+			*(u32 *)loc |= offset & 0x7fffffff;
 			break;
 
 		case R_ARM_MOVW_ABS_NC:

arch/arm/kernel/setup.c

@@ -81,7 +81,7 @@ __setup("fpe=", fpe_setup);
 extern void init_default_cache_policy(unsigned long);
 extern void paging_init(const struct machine_desc *desc);
 extern void early_paging_init(const struct machine_desc *);
-extern void sanity_check_meminfo(void);
+extern void adjust_lowmem_bounds(void);
 extern enum reboot_mode reboot_mode;
 extern void setup_dma_zone(const struct machine_desc *desc);
 
@@ -1093,8 +1093,14 @@ void __init setup_arch(char **cmdline_p)
 	setup_dma_zone(mdesc);
 	xen_early_init();
 	efi_init();
-	sanity_check_meminfo();
+	/*
+	 * Make sure the calculation for lowmem/highmem is set appropriately
+	 * before reserving/allocating any mmeory
+	 */
+	adjust_lowmem_bounds();
 	arm_memblock_init(mdesc);
+	/* Memory may have been removed so recalculate the bounds. */
+	adjust_lowmem_bounds();
 
 	early_ioremap_reset();
 

arch/arm/kernel/smp.c

@@ -251,7 +251,7 @@ void __cpu_die(unsigned int cpu)
 		pr_err("CPU%u: cpu didn't die\n", cpu);
 		return;
 	}
-	pr_notice("CPU%u: shutdown\n", cpu);
+	pr_debug("CPU%u: shutdown\n", cpu);
 
 	/*
 	 * platform_cpu_kill() is generally expected to do the powering off

arch/arm/mach-alpine/platsmp.c

@@ -27,7 +27,7 @@ static int alpine_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	phys_addr_t addr;
 
-	addr = virt_to_phys(secondary_startup);
+	addr = __pa_symbol(secondary_startup);
 
 	if (addr > (phys_addr_t)(uint32_t)(-1)) {
 		pr_err("FAIL: resume address over 32bit (%pa)", &addr);

arch/arm/mach-axxia/platsmp.c

@@ -25,7 +25,7 @@
 static void write_release_addr(u32 release_phys)
 {
 	u32 *virt = (u32 *) phys_to_virt(release_phys);
-	writel_relaxed(virt_to_phys(secondary_startup), virt);
+	writel_relaxed(__pa_symbol(secondary_startup), virt);
 	/* Make sure this store is visible to other CPUs */
 	smp_wmb();
 	__cpuc_flush_dcache_area(virt, sizeof(u32));

arch/arm/mach-bcm/bcm63xx_smp.c

@@ -135,7 +135,7 @@ static int bcm63138_smp_boot_secondary(unsigned int cpu,
 	}
 
 	/* Write the secondary init routine to the BootLUT reset vector */
-	val = virt_to_phys(secondary_startup);
+	val = __pa_symbol(secondary_startup);
 	writel_relaxed(val, bootlut_base + BOOTLUT_RESET_VECT);
 
 	/* Power up the core, will jump straight to its reset vector when we

arch/arm/mach-bcm/platsmp-brcmstb.c

@@ -151,7 +151,7 @@ static void brcmstb_cpu_boot(u32 cpu)
 	 * Set the reset vector to point to the secondary_startup
 	 * routine
 	 */
-	cpu_set_boot_addr(cpu, virt_to_phys(secondary_startup));
+	cpu_set_boot_addr(cpu, __pa_symbol(secondary_startup));
 
 	/* Unhalt the cpu */
 	cpu_rst_cfg_set(cpu, 0);

arch/arm/mach-bcm/platsmp.c

@@ -116,7 +116,7 @@ static int nsp_write_lut(unsigned int cpu)
 		return -ENOMEM;
 	}
 
-	secondary_startup_phy = virt_to_phys(secondary_startup);
+	secondary_startup_phy = __pa_symbol(secondary_startup);
 	BUG_ON(secondary_startup_phy > (phys_addr_t)U32_MAX);
 
 	writel_relaxed(secondary_startup_phy, sku_rom_lut);
@@ -189,7 +189,7 @@ static int kona_boot_secondary(unsigned int cpu, struct task_struct *idle)
 	 * Secondary cores will start in secondary_startup(),
 	 * defined in "arch/arm/kernel/head.S"
 	 */
-	boot_func = virt_to_phys(secondary_startup);
+	boot_func = __pa_symbol(secondary_startup);
 	BUG_ON(boot_func & BOOT_ADDR_CPUID_MASK);
 	BUG_ON(boot_func > (phys_addr_t)U32_MAX);
 

arch/arm/mach-berlin/platsmp.c

@@ -15,6 +15,7 @@
 
 #include <asm/cacheflush.h>
 #include <asm/cp15.h>
+#include <asm/memory.h>
 #include <asm/smp_plat.h>
 #include <asm/smp_scu.h>
 
@@ -75,7 +76,7 @@ static void __init berlin_smp_prepare_cpus(unsigned int max_cpus)
 	if (!cpu_ctrl)
 		goto unmap_scu;
 
-	vectors_base = ioremap(CONFIG_VECTORS_BASE, SZ_32K);
+	vectors_base = ioremap(VECTORS_BASE, SZ_32K);
 	if (!vectors_base)
 		goto unmap_scu;
 
@@ -92,7 +93,7 @@ static void __init berlin_smp_prepare_cpus(unsigned int max_cpus)
 	 * Write the secondary startup address into the SW reset address
 	 * vector. This is used by boot_inst.
 	 */
-	writel(virt_to_phys(secondary_startup), vectors_base + SW_RESET_ADDR);
+	writel(__pa_symbol(secondary_startup), vectors_base + SW_RESET_ADDR);
 
 	iounmap(vectors_base);
 unmap_scu:

arch/arm/mach-exynos/firmware.c

@@ -41,7 +41,7 @@ static int exynos_do_idle(unsigned long mode)
 	case FW_DO_IDLE_AFTR:
 		if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9)
 			exynos_save_cp15();
-		writel_relaxed(virt_to_phys(exynos_cpu_resume_ns),
+		writel_relaxed(__pa_symbol(exynos_cpu_resume_ns),
 			       sysram_ns_base_addr + 0x24);
 		writel_relaxed(EXYNOS_AFTR_MAGIC, sysram_ns_base_addr + 0x20);
 		if (soc_is_exynos3250()) {
@@ -135,7 +135,7 @@ static int exynos_suspend(void)
 		exynos_save_cp15();
 
 	writel(EXYNOS_SLEEP_MAGIC, sysram_ns_base_addr + EXYNOS_BOOT_FLAG);
-	writel(virt_to_phys(exynos_cpu_resume_ns),
+	writel(__pa_symbol(exynos_cpu_resume_ns),
 		sysram_ns_base_addr + EXYNOS_BOOT_ADDR);
 
 	return cpu_suspend(0, exynos_cpu_suspend);

arch/arm/mach-exynos/mcpm-exynos.c

@@ -221,7 +221,7 @@ static void exynos_mcpm_setup_entry_point(void)
 	 */
 	__raw_writel(0xe59f0000, ns_sram_base_addr);     /* ldr r0, [pc, #0] */
 	__raw_writel(0xe12fff10, ns_sram_base_addr + 4); /* bx  r0 */
-	__raw_writel(virt_to_phys(mcpm_entry_point), ns_sram_base_addr + 8);
+	__raw_writel(__pa_symbol(mcpm_entry_point), ns_sram_base_addr + 8);
 }
 
 static struct syscore_ops exynos_mcpm_syscore_ops = {

arch/arm/mach-exynos/platsmp.c

@@ -353,7 +353,7 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle)
 
 		smp_rmb();
 
-		boot_addr = virt_to_phys(exynos4_secondary_startup);
+		boot_addr = __pa_symbol(exynos4_secondary_startup);
 
 		ret = exynos_set_boot_addr(core_id, boot_addr);
 		if (ret)
@@ -413,7 +413,7 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus)
 
 		mpidr = cpu_logical_map(i);
 		core_id = MPIDR_AFFINITY_LEVEL(mpidr, 0);
-		boot_addr = virt_to_phys(exynos4_secondary_startup);
+		boot_addr = __pa_symbol(exynos4_secondary_startup);
 
 		ret = exynos_set_boot_addr(core_id, boot_addr);
 		if (ret)