Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
  ARM: AMBA: Add pclk support to AMBA bus infrastructure
  ARM: 6278/2: fix regression in RealView after the introduction of pclk
  ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
  ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
  ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
  ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
  ARM: 6244/1: mmci: add variant data and default MCICLOCK support
  ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
  ARM: 6274/1: add global control registers definition header file for nuc900
  mx2_camera: fix type of dma buffer virtual address pointer
  mx2_camera: Add soc_camera support for i.MX25/i.MX27
  arm/imx/gpio: add spinlock protection
  ARM: Add support for the LPC32XX arch
  ARM: LPC32XX: Arch config menu supoport and makefiles
  ARM: LPC32XX: Phytec 3250 platform support
  ARM: LPC32XX: Misc support functions
  ARM: LPC32XX: Serial support code
  ARM: LPC32XX: System suspend support
  ARM: LPC32XX: GPIO, timer, and IRQ drivers
  ARM: LPC32XX: Clock driver
  ...

Documentation/arm/memory.txt

@@ -33,7 +33,13 @@ ffff0000	ffff0fff	CPU vector page.
 
 fffe0000	fffeffff	XScale cache flush area.  This is used
 				in proc-xscale.S to flush the whole data
-				cache.  Free for other usage on non-XScale.
+				cache. (XScale does not have TCM.)
+
+fffe8000	fffeffff	DTCM mapping area for platforms with
+				DTCM mounted inside the CPU.
+
+fffe0000	fffe7fff	ITCM mapping area for platforms with
+				ITCM mounted inside the CPU.
 
 fff00000	fffdffff	Fixmap mapping region.  Addresses provided
 				by fix_to_virt() will be located here.

Documentation/arm/tcm.txt

@@ -19,8 +19,8 @@ defines a CPUID_TCM register that you can read out from the
 system control coprocessor. Documentation from ARM can be found
 at http://infocenter.arm.com, search for "TCM Status Register"
 to see documents for all CPUs. Reading this register you can
-determine if ITCM (bit 0) and/or DTCM (bit 16) is present in the
-machine.
+determine if ITCM (bits 1-0) and/or DTCM (bit 17-16) is present
+in the machine.
 
 There is further a TCM region register (search for "TCM Region
 Registers" at the ARM site) that can report and modify the location
@@ -35,7 +35,15 @@ The TCM memory can then be remapped to another address again using
 the MMU, but notice that the TCM if often used in situations where
 the MMU is turned off. To avoid confusion the current Linux
 implementation will map the TCM 1 to 1 from physical to virtual
-memory in the location specified by the machine.
+memory in the location specified by the kernel. Currently Linux
+will map ITCM to 0xfffe0000 and on, and DTCM to 0xfffe8000 and
+on, supporting a maximum of 32KiB of ITCM and 32KiB of DTCM.
+
+Newer versions of the region registers also support dividing these
+TCMs in two separate banks, so for example an 8KiB ITCM is divided
+into two 4KiB banks with its own control registers. The idea is to
+be able to lock and hide one of the banks for use by the secure
+world (TrustZone).
 
 TCM is used for a few things:
 
@@ -65,18 +73,18 @@ in <asm/tcm.h>. Using this interface it is possible to:
   memory. Such a heap is great for things like saving
   device state when shutting off device power domains.
 
-A machine that has TCM memory shall select HAVE_TCM in
-arch/arm/Kconfig for itself, and then the
-rest of the functionality will depend on the physical
-location and size of ITCM and DTCM to be defined in
-mach/memory.h for the machine. Code that needs to use
-TCM shall #include <asm/tcm.h> If the TCM is not located
-at the place given in memory.h it will be moved using
-the TCM Region registers.
+A machine that has TCM memory shall select HAVE_TCM from
+arch/arm/Kconfig for itself. Code that needs to use TCM shall
+#include <asm/tcm.h>
 
 Functions to go into itcm can be tagged like this:
 int __tcmfunc foo(int bar);
 
+Since these are marked to become long_calls and you may want
+to have functions called locally inside the TCM without
+wasting space, there is also the __tcmlocalfunc prefix that
+will make the call relative.
+
 Variables to go into dtcm can be tagged like this:
 int __tcmdata foo;
 

arch/arm/Kconfig

@@ -10,6 +10,7 @@ config ARM
 	default y
 	select HAVE_AOUT
 	select HAVE_IDE
+	select HAVE_MEMBLOCK
 	select RTC_LIB
 	select SYS_SUPPORTS_APM_EMULATION
 	select GENERIC_ATOMIC64 if (!CPU_32v6K)
@@ -24,6 +25,7 @@ config ARM
 	select HAVE_KERNEL_LZMA
 	select HAVE_PERF_EVENTS
 	select PERF_USE_VMALLOC
+	select HAVE_REGS_AND_STACK_ACCESS_API
 	help
 	  The ARM series is a line of low-power-consumption RISC chip designs
 	  licensed by ARM Ltd and targeted at embedded applications and
@@ -55,7 +57,7 @@ config GENERIC_CLOCKEVENTS
 config GENERIC_CLOCKEVENTS_BROADCAST
 	bool
 	depends on GENERIC_CLOCKEVENTS
-	default y if SMP && !LOCAL_TIMERS
+	default y if SMP
 
 config HAVE_TCM
 	bool
@@ -301,6 +303,7 @@ config ARCH_CNS3XXX
 	select CPU_V6
 	select GENERIC_CLOCKEVENTS
 	select ARM_GIC
+	select PCI_DOMAINS if PCI
 	help
 	  Support for Cavium Networks CNS3XXX platform.
 
@@ -439,21 +442,6 @@ config ARCH_IXP4XX
 	help
 	  Support for Intel's IXP4XX (XScale) family of processors.
 
-config ARCH_L7200
-	bool "LinkUp-L7200"
-	select CPU_ARM720T
-	select FIQ
-	select ARCH_USES_GETTIMEOFFSET
-	help
-	  Say Y here if you intend to run this kernel on a LinkUp Systems
-	  L7200 Software Development Board which uses an ARM720T processor.
-	  Information on this board can be obtained at:
-
-	  <http://www.linkupsys.com/>
-
-	  If you have any questions or comments about the Linux kernel port
-	  to this board, send e-mail to <sjhill@cotw.com>.
-
 config ARCH_DOVE
 	bool "Marvell Dove"
 	select PCI
@@ -482,6 +470,19 @@ config ARCH_LOKI
 	help
 	  Support for the Marvell Loki (88RC8480) SoC.
 
+config ARCH_LPC32XX
+	bool "NXP LPC32XX"
+	select CPU_ARM926T
+	select ARCH_REQUIRE_GPIOLIB
+	select HAVE_IDE
+	select ARM_AMBA
+	select USB_ARCH_HAS_OHCI
+	select COMMON_CLKDEV
+	select GENERIC_TIME
+	select GENERIC_CLOCKEVENTS
+	help
+	  Support for the NXP LPC32XX family of processors
+
 config ARCH_MV78XX0
 	bool "Marvell MV78xx0"
 	select CPU_FEROCEON
@@ -586,6 +587,7 @@ config ARCH_MSM
 	bool "Qualcomm MSM"
 	select HAVE_CLK
 	select GENERIC_CLOCKEVENTS
+	select ARCH_REQUIRE_GPIOLIB
 	help
 	  Support for Qualcomm MSM/QSD based systems.  This runs on the
 	  apps processor of the MSM/QSD and depends on a shared memory
@@ -719,7 +721,6 @@ config ARCH_SHARK
 config ARCH_LH7A40X
 	bool "Sharp LH7A40X"
 	select CPU_ARM922T
-	select ARCH_DISCONTIGMEM_ENABLE if !LH7A40X_CONTIGMEM
 	select ARCH_SPARSEMEM_ENABLE if !LH7A40X_CONTIGMEM
 	select ARCH_USES_GETTIMEOFFSET
 	help
@@ -845,6 +846,8 @@ source "arch/arm/mach-lh7a40x/Kconfig"
 
 source "arch/arm/mach-loki/Kconfig"
 
+source "arch/arm/mach-lpc32xx/Kconfig"
+
 source "arch/arm/mach-msm/Kconfig"
 
 source "arch/arm/mach-mv78xx0/Kconfig"
@@ -1031,11 +1034,6 @@ endmenu
 
 source "arch/arm/common/Kconfig"
 
-config FORCE_MAX_ZONEORDER
-	int
-	depends on SA1111
-	default "9"
-
 menu "Bus support"
 
 config ARM_AMBA
@@ -1060,7 +1058,7 @@ config ISA_DMA_API
 	bool
 
 config PCI
-	bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695 || MACH_ARMCORE
+	bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695 || MACH_ARMCORE || ARCH_CNS3XXX
 	help
 	  Find out whether you have a PCI motherboard. PCI is the name of a
 	  bus system, i.e. the way the CPU talks to the other stuff inside
@@ -1172,9 +1170,10 @@ config HOTPLUG_CPU
 config LOCAL_TIMERS
 	bool "Use local timer interrupts"
 	depends on SMP && (REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || \
-		REALVIEW_EB_A9MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || ARCH_U8500)
+		REALVIEW_EB_A9MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \
+		ARCH_U8500 || ARCH_VEXPRESS_CA9X4)
 	default y
-	select HAVE_ARM_TWD if (ARCH_REALVIEW || ARCH_OMAP4 || ARCH_U8500)
+	select HAVE_ARM_TWD if (ARCH_REALVIEW || ARCH_VEXPRESS || ARCH_OMAP4 || ARCH_U8500)
 	help
 	  Enable support for local timers on SMP platforms, rather then the
 	  legacy IPI broadcast method.  Local timers allows the system
@@ -1185,10 +1184,10 @@ source kernel/Kconfig.preempt
 
 config HZ
 	int
-	default 128 if ARCH_L7200
 	default 200 if ARCH_EBSA110 || ARCH_S3C2410 || ARCH_S5P6440 || ARCH_S5P6442 || ARCH_S5PV210
 	default OMAP_32K_TIMER_HZ if ARCH_OMAP && OMAP_32K_TIMER
 	default AT91_TIMER_HZ if ARCH_AT91
+	default SHMOBILE_TIMER_HZ if ARCH_SHMOBILE
 	default 100
 
 config THUMB2_KERNEL
@@ -1241,10 +1240,6 @@ config OABI_COMPAT
 config ARCH_HAS_HOLES_MEMORYMODEL
 	bool
 
-# Discontigmem is deprecated
-config ARCH_DISCONTIGMEM_ENABLE
-	bool
-
 config ARCH_SPARSEMEM_ENABLE
 	bool
 
@@ -1252,13 +1247,7 @@ config ARCH_SPARSEMEM_DEFAULT
 	def_bool ARCH_SPARSEMEM_ENABLE
 
 config ARCH_SELECT_MEMORY_MODEL
-	def_bool ARCH_DISCONTIGMEM_ENABLE && ARCH_SPARSEMEM_ENABLE
-
-config NODES_SHIFT
-	int
-	default "4" if ARCH_LH7A40X
-	default "2"
-	depends on NEED_MULTIPLE_NODES
+	def_bool ARCH_SPARSEMEM_ENABLE
 
 config HIGHMEM
 	bool "High Memory Support (EXPERIMENTAL)"
@@ -1290,8 +1279,33 @@ config HW_PERF_EVENTS
 	  Enable hardware performance counter support for perf events. If
 	  disabled, perf events will use software events only.
 
+config SPARSE_IRQ
+	def_bool n
+	help
+	  This enables support for sparse irqs. This is useful in general
+	  as most CPUs have a fairly sparse array of IRQ vectors, which
+	  the irq_desc then maps directly on to. Systems with a high
+	  number of off-chip IRQs will want to treat this as
+	  experimental until they have been independently verified.
+
 source "mm/Kconfig"
 
+config FORCE_MAX_ZONEORDER
+	int "Maximum zone order" if ARCH_SHMOBILE
+	range 11 64 if ARCH_SHMOBILE
+	default "9" if SA1111
+	default "11"
+	help
+	  The kernel memory allocator divides physically contiguous memory
+	  blocks into "zones", where each zone is a power of two number of
+	  pages.  This option selects the largest power of two that the kernel
+	  keeps in the memory allocator.  If you need to allocate very large
+	  blocks of physically contiguous memory, then you may need to
+	  increase this value.
+
+	  This config option is actually maximum order plus one. For example,
+	  a value of 11 means that the largest free memory block is 2^10 pages.
+
 config LEDS
 	bool "Timer and CPU usage LEDs"
 	depends on ARCH_CDB89712 || ARCH_EBSA110 || \
@@ -1375,6 +1389,24 @@ config UACCESS_WITH_MEMCPY
 	  However, if the CPU data cache is using a write-allocate mode,
 	  this option is unlikely to provide any performance gain.
 
+config CC_STACKPROTECTOR
+	bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
+	help
+	  This option turns on the -fstack-protector GCC feature. This
+	  feature puts, at the beginning of functions, a canary value on
+	  the stack just before the return address, and validates
+	  the value just before actually returning.  Stack based buffer
+	  overflows (that need to overwrite this return address) now also
+	  overwrite the canary, which gets detected and the attack is then
+	  neutralized via a kernel panic.
+	  This feature requires gcc version 4.2 or above.
+
+config DEPRECATED_PARAM_STRUCT
+	bool "Provide old way to pass kernel parameters"
+	help
+	  This was deprecated in 2001 and announced to live on for 5 years.
+	  Some old boot loaders still use this way.
+
 endmenu
 
 menu "Boot options"
@@ -1485,6 +1517,105 @@ config ATAGS_PROC
 	  Should the atags used to boot the kernel be exported in an "atags"
 	  file in procfs. Useful with kexec.
 
+config AUTO_ZRELADDR
+	bool "Auto calculation of the decompressed kernel image address"
+	depends on !ZBOOT_ROM && !ARCH_U300
+	help
+	  ZRELADDR is the physical address where the decompressed kernel
+	  image will be placed. If AUTO_ZRELADDR is selected, the address
+	  will be determined at run-time by masking the current IP with
+	  0xf8000000. This assumes the zImage being placed in the first 128MB
+	  from start of memory.
+
+config ZRELADDR
+	hex "Physical address of the decompressed kernel image"
+	depends on !AUTO_ZRELADDR
+	default 0x00008000 if ARCH_BCMRING ||\
+		ARCH_CNS3XXX ||\
+		ARCH_DOVE ||\
+		ARCH_EBSA110 ||\
+		ARCH_FOOTBRIDGE ||\
+		ARCH_INTEGRATOR ||\
+		ARCH_IOP13XX ||\
+		ARCH_IOP33X ||\
+		ARCH_IXP2000 ||\
+		ARCH_IXP23XX ||\
+		ARCH_IXP4XX ||\
+		ARCH_KIRKWOOD ||\
+		ARCH_KS8695 ||\
+		ARCH_LOKI ||\
+		ARCH_MMP ||\
+		ARCH_MV78XX0 ||\
+		ARCH_NOMADIK ||\
+		ARCH_NUC93X ||\
+		ARCH_NS9XXX ||\
+		ARCH_ORION5X ||\
+		ARCH_SPEAR3XX ||\
+		ARCH_SPEAR6XX ||\
+		ARCH_U8500 ||\
+		ARCH_VERSATILE ||\
+		ARCH_W90X900
+	default 0x08008000 if ARCH_MX1 ||\
+		ARCH_SHARK
+	default 0x10008000 if ARCH_MSM ||\
+		ARCH_OMAP1 ||\
+		ARCH_RPC
+	default 0x20008000 if ARCH_S5P6440 ||\
+		ARCH_S5P6442 ||\
+		ARCH_S5PC100 ||\
+		ARCH_S5PV210
+	default 0x30008000 if ARCH_S3C2410 ||\
+		ARCH_S3C2400 ||\
+		ARCH_S3C2412 ||\
+		ARCH_S3C2416 ||\
+		ARCH_S3C2440 ||\
+		ARCH_S3C2443
+	default 0x40008000 if ARCH_STMP378X ||\
+		ARCH_STMP37XX ||\
+		ARCH_SH7372 ||\
+		ARCH_SH7377
+	default 0x50008000 if ARCH_S3C64XX ||\
+		ARCH_SH7367
+	default 0x60008000 if ARCH_VEXPRESS
+	default 0x80008000 if ARCH_MX25 ||\
+		ARCH_MX3 ||\
+		ARCH_NETX ||\
+		ARCH_OMAP2PLUS ||\
+		ARCH_PNX4008
+	default 0x90008000 if ARCH_MX5 ||\
+		ARCH_MX91231
+	default 0xa0008000 if ARCH_IOP32X ||\
+		ARCH_PXA ||\
+		MACH_MX27
+	default 0xc0008000 if ARCH_LH7A40X ||\
+		MACH_MX21
+	default 0xf0008000 if ARCH_AAEC2000 ||\
+		ARCH_L7200
+	default 0xc0028000 if ARCH_CLPS711X
+	default 0x70008000 if ARCH_AT91 && (ARCH_AT91CAP9 || ARCH_AT91SAM9G45)
+	default 0x20008000 if ARCH_AT91 && !(ARCH_AT91CAP9 || ARCH_AT91SAM9G45)
+	default 0xc0008000 if ARCH_DAVINCI && ARCH_DAVINCI_DA8XX
+	default 0x80008000 if ARCH_DAVINCI && !ARCH_DAVINCI_DA8XX
+	default 0x00008000 if ARCH_EP93XX && EP93XX_SDCE3_SYNC_PHYS_OFFSET
+	default 0xc0008000 if ARCH_EP93XX && EP93XX_SDCE0_PHYS_OFFSET
+	default 0xd0008000 if ARCH_EP93XX && EP93XX_SDCE1_PHYS_OFFSET
+	default 0xe0008000 if ARCH_EP93XX && EP93XX_SDCE2_PHYS_OFFSET
+	default 0xf0008000 if ARCH_EP93XX && EP93XX_SDCE3_ASYNC_PHYS_OFFSET
+	default 0x00008000 if ARCH_GEMINI && GEMINI_MEM_SWAP
+	default 0x10008000 if ARCH_GEMINI && !GEMINI_MEM_SWAP
+	default 0x70008000 if ARCH_REALVIEW && REALVIEW_HIGH_PHYS_OFFSET
+	default 0x00008000 if ARCH_REALVIEW && !REALVIEW_HIGH_PHYS_OFFSET
+	default 0xc0208000 if ARCH_SA1100 && SA1111
+	default 0xc0008000 if ARCH_SA1100 && !SA1111
+	default 0x30108000 if ARCH_S3C2410 && PM_H1940
+	default 0x28E08000 if ARCH_U300 && MACH_U300_SINGLE_RAM
+	default 0x48008000 if ARCH_U300 && !MACH_U300_SINGLE_RAM
+	help
+	  ZRELADDR is the physical address where the decompressed kernel
+	  image will be placed. ZRELADDR has to be specified when the
+	  assumption of AUTO_ZRELADDR is not valid, or when ZBOOT_ROM is
+	  selected.
+
 endmenu
 
 menu "CPU Power Management"

arch/arm/Makefile

@@ -34,6 +34,10 @@ ifeq ($(CONFIG_FRAME_POINTER),y)
 KBUILD_CFLAGS	+=-fno-omit-frame-pointer -mapcs -mno-sched-prolog
 endif
 
+ifeq ($(CONFIG_CC_STACKPROTECTOR),y)
+KBUILD_CFLAGS	+=-fstack-protector
+endif
+
 ifeq ($(CONFIG_CPU_BIG_ENDIAN),y)
 KBUILD_CPPFLAGS	+= -mbig-endian
 AS		+= -EB
@@ -139,14 +143,14 @@ machine-$(CONFIG_ARCH_IXP23XX)		:= ixp23xx
 machine-$(CONFIG_ARCH_IXP4XX)		:= ixp4xx
 machine-$(CONFIG_ARCH_KIRKWOOD)		:= kirkwood
 machine-$(CONFIG_ARCH_KS8695)		:= ks8695
-machine-$(CONFIG_ARCH_L7200)		:= l7200
 machine-$(CONFIG_ARCH_LH7A40X)		:= lh7a40x
 machine-$(CONFIG_ARCH_LOKI) 		:= loki
+machine-$(CONFIG_ARCH_LPC32XX)		:= lpc32xx
 machine-$(CONFIG_ARCH_MMP)		:= mmp
 machine-$(CONFIG_ARCH_MSM)		:= msm
 machine-$(CONFIG_ARCH_MV78XX0)		:= mv78xx0
-machine-$(CONFIG_ARCH_MX1)		:= mx1
-machine-$(CONFIG_ARCH_MX2)		:= mx2
+machine-$(CONFIG_ARCH_MX1)		:= imx
+machine-$(CONFIG_ARCH_MX2)		:= imx
 machine-$(CONFIG_ARCH_MX25)		:= mx25
 machine-$(CONFIG_ARCH_MX3)		:= mx3
 machine-$(CONFIG_ARCH_MX5)		:= mx5

arch/arm/boot/Makefile

@@ -14,18 +14,16 @@
 MKIMAGE         := $(srctree)/scripts/mkuboot.sh
 
 ifneq ($(MACHINE),)
-include $(srctree)/$(MACHINE)/Makefile.boot
+-include $(srctree)/$(MACHINE)/Makefile.boot
 endif
 
 # Note: the following conditions must always be true:
-#   ZRELADDR == virt_to_phys(PAGE_OFFSET + TEXT_OFFSET)
 #   PARAMS_PHYS must be within 4MB of ZRELADDR
 #   INITRD_PHYS must be in RAM
-ZRELADDR    := $(zreladdr-y)
 PARAMS_PHYS := $(params_phys-y)
 INITRD_PHYS := $(initrd_phys-y)
 
-export ZRELADDR INITRD_PHYS PARAMS_PHYS
+export INITRD_PHYS PARAMS_PHYS
 
 targets := Image zImage xipImage bootpImage uImage
 
@@ -67,7 +65,7 @@ quiet_cmd_uimage = UIMAGE  $@
 ifeq ($(CONFIG_ZBOOT_ROM),y)
 $(obj)/uImage: LOADADDR=$(CONFIG_ZBOOT_ROM_TEXT)
 else
-$(obj)/uImage: LOADADDR=$(ZRELADDR)
+$(obj)/uImage: LOADADDR=$(CONFIG_ZRELADDR)
 endif
 
 ifeq ($(CONFIG_THUMB2_KERNEL),y)

arch/arm/boot/compressed/Makefile

@@ -4,6 +4,7 @@
 # create a compressed vmlinuz image from the original vmlinux
 #
 
+AFLAGS_head.o += -DTEXT_OFFSET=$(TEXT_OFFSET)
 HEAD	= head.o
 OBJS	= misc.o decompress.o
 FONTC	= $(srctree)/drivers/video/console/font_acorn_8x8.c
@@ -19,10 +20,6 @@ ifeq ($(CONFIG_ARCH_SHARK),y)
 OBJS		+= head-shark.o ofw-shark.o
 endif
 
-ifeq ($(CONFIG_ARCH_L7200),y)
-OBJS		+= head-l7200.o
-endif
-
 ifeq ($(CONFIG_ARCH_P720T),y)
 # Borrow this code from SA1100
 OBJS		+= head-sa1100.o
@@ -82,19 +79,9 @@ endif
 EXTRA_CFLAGS  := -fpic -fno-builtin
 EXTRA_AFLAGS  := -Wa,-march=all
 
-# Supply ZRELADDR, INITRD_PHYS and PARAMS_PHYS to the decompressor via
-# linker symbols.  We only define initrd_phys and params_phys if the
-# machine class defined the corresponding makefile variable.
-LDFLAGS_vmlinux := --defsym zreladdr=$(ZRELADDR)
 ifeq ($(CONFIG_CPU_ENDIAN_BE8),y)
 LDFLAGS_vmlinux += --be8
 endif
-ifneq ($(INITRD_PHYS),)
-LDFLAGS_vmlinux += --defsym initrd_phys=$(INITRD_PHYS)
-endif
-ifneq ($(PARAMS_PHYS),)
-LDFLAGS_vmlinux += --defsym params_phys=$(PARAMS_PHYS)
-endif
 # ?
 LDFLAGS_vmlinux += -p
 # Report unresolved symbol references

arch/arm/boot/compressed/Makefile.debug

@@ -1,23 +0,0 @@
-#
-# linux/arch/arm/boot/compressed/Makefile
-#
-# create a compressed vmlinux image from the original vmlinux
-#
-
-COMPRESSED_EXTRA=../../lib/ll_char_wr.o
-OBJECTS=misc-debug.o ll_char_wr.aout.o
-
-CFLAGS=-D__KERNEL__ -O2 -DSTDC_HEADERS -DSTANDALONE_DEBUG -Wall -I../../../../include -c
-
-test-gzip: piggy.aout.o $(OBJECTS)
-	$(CC) -o $@ $(OBJECTS) piggy.aout.o
-
-misc-debug.o: misc.c
-	$(CC) $(CFLAGS) -o $@ misc.c
-
-piggy.aout.o: piggy.o
-	arm-linuxelf-objcopy --change-leading-char -I elf32-arm -O arm-aout32-linux piggy.o piggy.aout.o
-
-ll_char_wr.aout.o: $(COMPRESSED_EXTRA)
-	arm-linuxelf-objcopy --change-leading-char -I elf32-arm -O arm-aout32-linux $(COMPRESSED_EXTRA) ll_char_wr.aout.o
-

arch/arm/boot/compressed/head-l7200.S

@@ -1,29 +0,0 @@
-/* 
- * linux/arch/arm/boot/compressed/head-l7200.S
- * 
- * Copyright (C) 2000 Steve Hill <sjhill@cotw.com>
- * 
- * Some code borrowed from Nicolas Pitre's 'head-sa1100.S' file. This
- * is merged with head.S by the linker.
- */
-
-#include <asm/mach-types.h>
-
-#ifndef CONFIG_ARCH_L7200
-#error What am I doing here...
-#endif
-
-		.section        ".start", "ax"
-
-__L7200_start:
-		mov	r0, #0x00100000		@ FLASH address of initrd
-		mov	r2, #0xf1000000		@ RAM address of initrd
-		add	r3, r2, #0x00700000	@ Size of initrd 
-1:
-		ldmia   r0!, {r4, r5, r6, r7}
-		stmia   r2!, {r4, r5, r6, r7}
-		cmp	r2, r3
-		ble	1b
-
-		mov	r8, #0			@ Zero it out
-		mov	r7, #MACH_TYPE_L7200	@ Set architecture ID

arch/arm/boot/compressed/head.S

@@ -170,9 +170,16 @@ not_angel:
 
 		.text
 		adr	r0, LC0
- ARM(		ldmia	r0, {r1, r2, r3, r4, r5, r6, r11, ip, sp})
- THUMB(		ldmia	r0, {r1, r2, r3, r4, r5, r6, r11, ip}	)
+ ARM(		ldmia	r0, {r1, r2, r3, r5, r6, r11, ip, sp})
+ THUMB(		ldmia	r0, {r1, r2, r3, r5, r6, r11, ip}	)
  THUMB(		ldr	sp, [r0, #32]				)
+#ifdef CONFIG_AUTO_ZRELADDR
+		@ determine final kernel image address
+		and	r4, pc, #0xf8000000
+		add	r4, r4, #TEXT_OFFSET
+#else
+		ldr	r4, =CONFIG_ZRELADDR
+#endif
 		subs	r0, r0, r1		@ calculate the delta offset
 
 						@ if delta is zero, we are
@@ -310,18 +317,17 @@ wont_overwrite:	mov	r0, r4
 LC0:		.word	LC0			@ r1
 		.word	__bss_start		@ r2
 		.word	_end			@ r3
-		.word	zreladdr		@ r4
 		.word	_start			@ r5
 		.word	_image_size		@ r6
 		.word	_got_start		@ r11
 		.word	_got_end		@ ip
-		.word	user_stack+4096		@ sp
+		.word	user_stack_end		@ sp
 LC1:		.word	reloc_end - reloc_start
 		.size	LC0, . - LC0
 
 #ifdef CONFIG_ARCH_RPC
 		.globl	params
-params:		ldr	r0, =params_phys
+params:		ldr	r0, =0x10000100		@ params_phys for RPC
 		mov	pc, lr
 		.ltorg
 		.align
@@ -339,9 +345,8 @@ params:		ldr	r0, =params_phys
  *  r4 = kernel execution address
  *  r7 = architecture number
  *  r8 = atags pointer
- *  r9 = run-time address of "start"  (???)
  * On exit,
- *  r1, r2, r3, r9, r10, r12 corrupted
+ *  r0, r1, r2, r3, r9, r10, r12 corrupted
  * This routine must preserve:
  *  r4, r5, r6, r7, r8
  */
@@ -396,12 +401,18 @@ __armv3_mpu_cache_on:
 
 		mov	r0, #0
 		mcr	p15, 0, r0, c7, c0, 0	@ invalidate whole cache v3
+		/*
+		 * ?? ARMv3 MMU does not allow reading the control register,
+		 * does this really work on ARMv3 MPU?
+		 */
 		mrc	p15, 0, r0, c1, c0, 0	@ read control reg
 						@ .... .... .... WC.M
 		orr	r0, r0, #0x000d		@ .... .... .... 11.1
+		/* ?? this overwrites the value constructed above? */
 		mov	r0, #0
 		mcr	p15, 0, r0, c1, c0, 0	@ write control reg
 
+		/* ?? invalidate for the second time? */
 		mcr	p15, 0, r0, c7, c0, 0	@ invalidate whole cache v3
 		mov	pc, lr
 
@@ -771,8 +782,10 @@ proc_types:
  * Turn off the Cache and MMU.  ARMv3 does not support
  * reading the control register, but ARMv4 does.
  *
- * On exit, r0, r1, r2, r3, r9, r12 corrupted
- * This routine must preserve: r4, r6, r7
+ * On exit,
+ *  r0, r1, r2, r3, r9, r12 corrupted
+ * This routine must preserve:
+ *  r4, r6, r7
  */
 		.align	5
 cache_off:	mov	r3, #12			@ cache_off function
@@ -845,7 +858,7 @@ __armv3_mmu_cache_off:
  * Clean and flush the cache to maintain consistency.
  *
  * On exit,
- *  r1, r2, r3, r9, r11, r12 corrupted
+ *  r1, r2, r3, r9, r10, r11, r12 corrupted
  * This routine must preserve:
  *  r0, r4, r5, r6, r7
  */
@@ -988,7 +1001,7 @@ no_cache_id:
 __armv3_mmu_cache_flush:
 __armv3_mpu_cache_flush:
 		mov	r1, #0
-		mcr	p15, 0, r0, c7, c0, 0	@ invalidate whole cache v3
+		mcr	p15, 0, r1, c7, c0, 0	@ invalidate whole cache v3
 		mov	pc, lr
 
 /*
@@ -1001,6 +1014,7 @@ __armv3_mpu_cache_flush:
 phexbuf:	.space	12
 		.size	phexbuf, . - phexbuf
 
+@ phex corrupts {r0, r1, r2, r3}
 phex:		adr	r3, phexbuf
 		mov	r2, #0
 		strb	r2, [r3, r1]
@@ -1015,6 +1029,7 @@ phex:		adr	r3, phexbuf
 		strb	r2, [r3, r1]
 		b	1b
 
+@ puts corrupts {r0, r1, r2, r3}
 puts:		loadsp	r3, r1
 1:		ldrb	r2, [r0], #1
 		teq	r2, #0
@@ -1029,12 +1044,14 @@ puts:		loadsp	r3, r1
 		teq	r0, #0
 		bne	1b
 		mov	pc, lr
+@ putc corrupts {r0, r1, r2, r3}
 putc:
 		mov	r2, r0
 		mov	r0, #0
 		loadsp	r3, r1
 		b	2b
 
+@ memdump corrupts {r0, r1, r2, r3, r10, r11, r12, lr}
 memdump:	mov	r12, r0
 		mov	r10, lr
 		mov	r11, #0
@@ -1070,3 +1087,4 @@ reloc_end:
 		.align
 		.section ".stack", "w"
 user_stack:	.space	4096
+user_stack_end:

arch/arm/boot/compressed/misc.c

@@ -28,9 +28,6 @@ unsigned int __machine_arch_type;
 
 #include <asm/unaligned.h>
 
-#ifdef STANDALONE_DEBUG
-#define putstr printf
-#else
 
 static void putstr(const char *ptr);
 extern void error(char *x);
@@ -116,7 +113,6 @@ static void putstr(const char *ptr)
 	flush();
 }
 
-#endif
 
 void *memcpy(void *__dest, __const void *__src, size_t __n)
 {
@@ -186,7 +182,6 @@ asmlinkage void __div0(void)
 
 extern void do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x));
 
-#ifndef STANDALONE_DEBUG
 
 unsigned long
 decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
@@ -211,18 +206,3 @@ decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
 	putstr(" done, booting the kernel.\n");
 	return output_ptr;
 }
-#else
-
-char output_buffer[1500*1024];
-
-int main()
-{
-	output_data = output_buffer;
-
-	putstr("Uncompressing Linux...");
-	decompress(input_data, input_data_end - input_data,
-			NULL, NULL, output_data, NULL, error);
-	putstr("done.\n");
-	return 0;
-}
-#endif

arch/arm/common/gic.c

@@ -108,6 +108,51 @@ static void gic_unmask_irq(unsigned int irq)
 	spin_unlock(&irq_controller_lock);
 }
 
+static int gic_set_type(unsigned int irq, unsigned int type)
+{
+	void __iomem *base = gic_dist_base(irq);
+	unsigned int gicirq = gic_irq(irq);
+	u32 enablemask = 1 << (gicirq % 32);
+	u32 enableoff = (gicirq / 32) * 4;
+	u32 confmask = 0x2 << ((gicirq % 16) * 2);
+	u32 confoff = (gicirq / 16) * 4;
+	bool enabled = false;
+	u32 val;
+
+	/* Interrupt configuration for SGIs can't be changed */
+	if (gicirq < 16)
+		return -EINVAL;
+
+	if (type != IRQ_TYPE_LEVEL_HIGH && type != IRQ_TYPE_EDGE_RISING)
+		return -EINVAL;
+
+	spin_lock(&irq_controller_lock);
+
+	val = readl(base + GIC_DIST_CONFIG + confoff);
+	if (type == IRQ_TYPE_LEVEL_HIGH)
+		val &= ~confmask;
+	else if (type == IRQ_TYPE_EDGE_RISING)
+		val |= confmask;
+
+	/*
+	 * As recommended by the spec, disable the interrupt before changing
+	 * the configuration
+	 */
+	if (readl(base + GIC_DIST_ENABLE_SET + enableoff) & enablemask) {
+		writel(enablemask, base + GIC_DIST_ENABLE_CLEAR + enableoff);
+		enabled = true;
+	}
+
+	writel(val, base + GIC_DIST_CONFIG + confoff);
+
+	if (enabled)
+		writel(enablemask, base + GIC_DIST_ENABLE_SET + enableoff);
+
+	spin_unlock(&irq_controller_lock);
+
+	return 0;
+}
+
 #ifdef CONFIG_SMP
 static int gic_set_cpu(unsigned int irq, const struct cpumask *mask_val)
 {
@@ -161,6 +206,7 @@ static struct irq_chip gic_chip = {
 	.ack		= gic_ack_irq,
 	.mask		= gic_mask_irq,
 	.unmask		= gic_unmask_irq,
+	.set_type	= gic_set_type,
 #ifdef CONFIG_SMP
 	.set_affinity	= gic_set_cpu,
 #endif

arch/arm/common/sa1111.c

@@ -185,13 +185,10 @@ static struct sa1111_dev_info sa1111_devices[] = {
 	},
 };
 
-void __init sa1111_adjust_zones(int node, unsigned long *size, unsigned long *holes)
+void __init sa1111_adjust_zones(unsigned long *size, unsigned long *holes)
 {
 	unsigned int sz = SZ_1M >> PAGE_SHIFT;
 
-	if (node != 0)
-		sz = 0;
-
 	size[1] = size[0] - sz;
 	size[0] = sz;
 }

arch/arm/configs/kirkwood_defconfig

@@ -13,11 +13,19 @@ CONFIG_MACH_RD88F6192_NAS=y
 CONFIG_MACH_RD88F6281=y
 CONFIG_MACH_MV88F6281GTW_GE=y
 CONFIG_MACH_SHEEVAPLUG=y
+CONFIG_MACH_ESATA_SHEEVAPLUG=y
+CONFIG_MACH_GURUPLUG=y
 CONFIG_MACH_TS219=y
 CONFIG_MACH_TS41X=y
 CONFIG_MACH_OPENRD_BASE=y
 CONFIG_MACH_OPENRD_CLIENT=y
+CONFIG_MACH_OPENRD_ULTIMATE=y
 CONFIG_MACH_NETSPACE_V2=y
+CONFIG_MACH_INETSPACE_V2=y
+CONFIG_MACH_NETSPACE_MAX_V2=y
+CONFIG_MACH_NET2BIG_V2=y
+CONFIG_MACH_NET5BIG_V2=y
+CONFIG_MACH_T5325=y
 # CONFIG_CPU_FEROCEON_OLD_ID is not set
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y

arch/arm/configs/lusl7200_defconfig

@@ -1,23 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EMBEDDED=y
-# CONFIG_HOTPLUG is not set
-CONFIG_MODULES=y
-CONFIG_ARCH_L7200=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ZBOOT_ROM_TEXT=0x00010000
-CONFIG_ZBOOT_ROM_BSS=0xf03e0000
-CONFIG_ZBOOT_ROM=y
-CONFIG_CMDLINE="console=tty0 console=ttyLU1,115200 root=/dev/ram initrd=0xf1000000,0x005dac7b mem=32M"
-CONFIG_BINFMT_AOUT=y
-CONFIG_BLK_DEV_RAM=y
-# CONFIG_INPUT is not set
-# CONFIG_SERIO_SERPORT is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_NONSTANDARD=y
-CONFIG_EXT2_FS=y
-CONFIG_DEBUG_USER=y
-# CONFIG_CRC32 is not set

arch/arm/include/asm/elf.h

@@ -121,4 +121,8 @@ int dump_task_regs(struct task_struct *t, elf_gregset_t *elfregs);
 extern void elf_set_personality(const struct elf32_hdr *);
 #define SET_PERSONALITY(ex)	elf_set_personality(&(ex))
 
+struct mm_struct;
+extern unsigned long arch_randomize_brk(struct mm_struct *mm);
+#define arch_randomize_brk arch_randomize_brk
+
 #endif

arch/arm/include/asm/hwcap.h

@@ -19,6 +19,7 @@
 #define HWCAP_NEON	4096
 #define HWCAP_VFPv3	8192
 #define HWCAP_VFPv3D16	16384
+#define HWCAP_TLS	32768
 
 #if defined(__KERNEL__) && !defined(__ASSEMBLY__)
 /*

arch/arm/include/asm/irq.h

@@ -7,6 +7,8 @@
 #define irq_canonicalize(i)	(i)
 #endif
 
+#define NR_IRQS_LEGACY	16
+
 /*
  * Use this value to indicate lack of interrupt
  * capability

arch/arm/include/asm/kexec.h

@@ -19,10 +19,26 @@
 
 #ifndef __ASSEMBLY__
 
-struct kimage;
-/* Provide a dummy definition to avoid build failures. */
+/**
+ * crash_setup_regs() - save registers for the panic kernel
+ * @newregs: registers are saved here
+ * @oldregs: registers to be saved (may be %NULL)
+ *
+ * Function copies machine registers from @oldregs to @newregs. If @oldregs is
+ * %NULL then current registers are stored there.
+ */
 static inline void crash_setup_regs(struct pt_regs *newregs,
-                                        struct pt_regs *oldregs) { }
+				    struct pt_regs *oldregs)
+{
+	if (oldregs) {
+		memcpy(newregs, oldregs, sizeof(*newregs));
+	} else {
+		__asm__ __volatile__ ("stmia %0, {r0 - r15}"
+				      : : "r" (&newregs->ARM_r0));
+		__asm__ __volatile__ ("mrs %0, cpsr"
+				      : "=r" (newregs->ARM_cpsr));
+	}
+}
 
 #endif /* __ASSEMBLY__ */
 

arch/arm/include/asm/mach/arch.h

@@ -20,6 +20,7 @@ struct machine_desc {
 	 * by assembler code in head.S, head-common.S
 	 */
 	unsigned int		nr;		/* architecture number	*/
+	unsigned int		nr_irqs;	/* number of IRQs */
 	unsigned int		phys_io;	/* start of physical io	*/
 	unsigned int		io_pg_offst;	/* byte offset for io 
 						 * page tabe entry	*/
@@ -37,6 +38,7 @@ struct machine_desc {
 	void			(*fixup)(struct machine_desc *,
 					 struct tag *, char **,
 					 struct meminfo *);
+	void			(*reserve)(void);/* reserve mem blocks	*/
 	void			(*map_io)(void);/* IO mapping function	*/
 	void			(*init_irq)(void);
 	struct sys_timer	*timer;		/* system tick timer	*/

arch/arm/include/asm/mach/irq.h

@@ -17,6 +17,7 @@ struct seq_file;
 /*
  * This is internal.  Do not use it.
  */
+extern unsigned int arch_nr_irqs;
 extern void (*init_arch_irq)(void);
 extern void init_FIQ(void);
 extern int show_fiq_list(struct seq_file *, void *);