Merge branches 'tracing/ftrace', 'tracing/textedit' and 'linus' into tracing/core

Documentation/feature-removal-schedule.txt

@@ -335,3 +335,12 @@ Why:	In 2.6.18 the Secmark concept was introduced to replace the "compat_net"
 	Secmark, it is time to deprecate the older mechanism and start the
 	process of removing the old code.
 Who:	Paul Moore <paul.moore@hp.com>
+---------------------------
+
+What:	sysfs ui for changing p4-clockmod parameters
+When:	September 2009
+Why:	See commits 129f8ae9b1b5be94517da76009ea956e89104ce8 and
+	e088e4c9cdb618675874becb91b2fd581ee707e6.
+	Removal is subject to fixing any remaining bugs in ACPI which may
+	cause the thermal throttling not to happen at the right time.
+Who:	Dave Jones <davej@redhat.com>, Matthew Garrett <mjg@redhat.com>

Documentation/networking/ipv6.txt

@@ -0,0 +1,35 @@
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either the
+/etc/modules.conf or /etc/modprobe.conf configuration file, or in a
+distro-specific configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+

arch/arm/mach-omap2/board-ldp.c

@@ -81,7 +81,7 @@ static inline void __init ldp_init_smc911x(void)
 	}
 
 	ldp_smc911x_resources[0].start = cs_mem_base + 0x0;
-	ldp_smc911x_resources[0].end   = cs_mem_base + 0xf;
+	ldp_smc911x_resources[0].end   = cs_mem_base + 0xff;
 	udelay(100);
 
 	eth_gpio = LDP_SMC911X_GPIO;

arch/x86/kernel/alternative.c

@@ -526,13 +526,12 @@ void *__kprobes text_poke(void *addr, const void *opcode, size_t len)
 		pages[1] = virt_to_page(addr + PAGE_SIZE);
 	}
 	BUG_ON(!pages[0]);
+	local_irq_save(flags);
 	set_fixmap(FIX_TEXT_POKE0, page_to_phys(pages[0]));
 	if (pages[1])
 		set_fixmap(FIX_TEXT_POKE1, page_to_phys(pages[1]));
 	vaddr = (char *)fix_to_virt(FIX_TEXT_POKE0);
-	local_irq_save(flags);
 	memcpy(&vaddr[(unsigned long)addr & ~PAGE_MASK], opcode, len);
-	local_irq_restore(flags);
 	clear_fixmap(FIX_TEXT_POKE0);
 	if (pages[1])
 		clear_fixmap(FIX_TEXT_POKE1);
@@ -542,5 +541,6 @@ void *__kprobes text_poke(void *addr, const void *opcode, size_t len)
 	   that causes hangs on some VIA CPUs. */
 	for (i = 0; i < len; i++)
 		BUG_ON(((char *)addr)[i] != ((char *)opcode)[i]);
+	local_irq_restore(flags);
 	return addr;
 }

arch/x86/kernel/cpu/cpufreq/p4-clockmod.c

@@ -277,7 +277,6 @@ static struct cpufreq_driver p4clockmod_driver = {
 	.name		= "p4-clockmod",
 	.owner		= THIS_MODULE,
 	.attr		= p4clockmod_attr,
-	.hide_interface	= 1,
 };
 
 

arch/x86/lguest/boot.c

@@ -348,6 +348,11 @@ static void lguest_cpuid(unsigned int *ax, unsigned int *bx,
 		 * flush_tlb_user() for both user and kernel mappings unless
 		 * the Page Global Enable (PGE) feature bit is set. */
 		*dx |= 0x00002000;
+		/* We also lie, and say we're family id 5.  6 or greater
+		 * leads to a rdmsr in early_init_intel which we can't handle.
+		 * Family ID is returned as bits 8-12 in ax. */
+		*ax &= 0xFFFFF0FF;
+		*ax |= 0x00000500;
 		break;
 	case 0x80000000:
 		/* Futureproof this a little: if they ask how much extended
@@ -594,19 +599,21 @@ static void __init lguest_init_IRQ(void)
 		/* Some systems map "vectors" to interrupts weirdly.  Lguest has
 		 * a straightforward 1 to 1 mapping, so force that here. */
 		__get_cpu_var(vector_irq)[vector] = i;
-		if (vector != SYSCALL_VECTOR) {
-			set_intr_gate(vector,
-				      interrupt[vector-FIRST_EXTERNAL_VECTOR]);
-			set_irq_chip_and_handler_name(i, &lguest_irq_controller,
-						      handle_level_irq,
-						      "level");
-		}
+		if (vector != SYSCALL_VECTOR)
+			set_intr_gate(vector, interrupt[i]);
 	}
 	/* This call is required to set up for 4k stacks, where we have
 	 * separate stacks for hard and soft interrupts. */
 	irq_ctx_init(smp_processor_id());
 }
 
+void lguest_setup_irq(unsigned int irq)
+{
+	irq_to_desc_alloc_cpu(irq, 0);
+	set_irq_chip_and_handler_name(irq, &lguest_irq_controller,
+				      handle_level_irq, "level");
+}
+
 /*
  * Time.
  *

drivers/block/aoe/aoedev.c

@@ -173,7 +173,7 @@ skbfree(struct sk_buff *skb)
 		return;
 	while (atomic_read(&skb_shinfo(skb)->dataref) != 1 && i-- > 0)
 		msleep(Sms);
-	if (i <= 0) {
+	if (i < 0) {
 		printk(KERN_ERR
 			"aoe: %s holds ref: %s\n",
 			skb->dev ? skb->dev->name : "netif",

drivers/cpufreq/cpufreq.c

@@ -754,11 +754,6 @@ static struct kobj_type ktype_cpufreq = {
 	.release	= cpufreq_sysfs_release,
 };
 
-static struct kobj_type ktype_empty_cpufreq = {
-	.sysfs_ops	= &sysfs_ops,
-	.release	= cpufreq_sysfs_release,
-};
-
 
 /**
  * cpufreq_add_dev - add a CPU device
@@ -892,36 +887,26 @@ static int cpufreq_add_dev(struct sys_device *sys_dev)
 	memcpy(&new_policy, policy, sizeof(struct cpufreq_policy));
 
 	/* prepare interface data */
-	if (!cpufreq_driver->hide_interface) {
-		ret = kobject_init_and_add(&policy->kobj, &ktype_cpufreq,
-					   &sys_dev->kobj, "cpufreq");
+	ret = kobject_init_and_add(&policy->kobj, &ktype_cpufreq, &sys_dev->kobj,
+				   "cpufreq");
+	if (ret)
+		goto err_out_driver_exit;
+
+	/* set up files for this cpu device */
+	drv_attr = cpufreq_driver->attr;
+	while ((drv_attr) && (*drv_attr)) {
+		ret = sysfs_create_file(&policy->kobj, &((*drv_attr)->attr));
 		if (ret)
 			goto err_out_driver_exit;
-
-		/* set up files for this cpu device */
-		drv_attr = cpufreq_driver->attr;
-		while ((drv_attr) && (*drv_attr)) {
-			ret = sysfs_create_file(&policy->kobj,
-						&((*drv_attr)->attr));
-			if (ret)
-				goto err_out_driver_exit;
-			drv_attr++;
-		}
-		if (cpufreq_driver->get) {
-			ret = sysfs_create_file(&policy->kobj,
-						&cpuinfo_cur_freq.attr);
-			if (ret)
-				goto err_out_driver_exit;
-		}
-		if (cpufreq_driver->target) {
-			ret = sysfs_create_file(&policy->kobj,
-						&scaling_cur_freq.attr);
-			if (ret)
-				goto err_out_driver_exit;
-		}
-	} else {
-		ret = kobject_init_and_add(&policy->kobj, &ktype_empty_cpufreq,
-					   &sys_dev->kobj, "cpufreq");
+		drv_attr++;
+	}
+	if (cpufreq_driver->get) {
+		ret = sysfs_create_file(&policy->kobj, &cpuinfo_cur_freq.attr);
+		if (ret)
+			goto err_out_driver_exit;
+	}
+	if (cpufreq_driver->target) {
+		ret = sysfs_create_file(&policy->kobj, &scaling_cur_freq.attr);
 		if (ret)
 			goto err_out_driver_exit;
 	}

drivers/lguest/lguest_device.c

@@ -212,6 +212,9 @@ static void lg_notify(struct virtqueue *vq)
 	hcall(LHCALL_NOTIFY, lvq->config.pfn << PAGE_SHIFT, 0, 0);
 }
 
+/* An extern declaration inside a C file is bad form.  Don't do it. */
+extern void lguest_setup_irq(unsigned int irq);
+
 /* This routine finds the first virtqueue described in the configuration of
  * this device and sets it up.
  *
@@ -266,6 +269,9 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev,
 		goto unmap;
 	}
 
+	/* Make sure the interrupt is allocated. */
+	lguest_setup_irq(lvq->config.irq);
+
 	/* Tell the interrupt for this virtqueue to go to the virtio_ring
 	 * interrupt handler. */
 	/* FIXME: We used to have a flag for the Host to tell us we could use

drivers/net/arm/ks8695net.c

@@ -560,7 +560,7 @@ ks8695_reset(struct ks8695_priv *ksp)
 		msleep(1);
 	}
 
-	if (reset_timeout == 0) {
+	if (reset_timeout < 0) {
 		dev_crit(ksp->dev,
 			 "Timeout waiting for DMA engines to reset\n");
 		/* And blithely carry on */

drivers/net/bonding/bond_main.c

@@ -4113,7 +4113,7 @@ static int bond_neigh_setup(struct net_device *dev, struct neigh_parms *parms)
 		const struct net_device_ops *slave_ops
 			= slave->dev->netdev_ops;
 		if (slave_ops->ndo_neigh_setup)
-			return slave_ops->ndo_neigh_setup(dev, parms);
+			return slave_ops->ndo_neigh_setup(slave->dev, parms);
 	}
 	return 0;
 }

drivers/net/jme.c

@@ -957,13 +957,14 @@ jme_process_receive(struct jme_adapter *jme, int limit)
 		goto out_inc;
 
 	i = atomic_read(&rxring->next_to_clean);
-	while (limit-- > 0) {
+	while (limit > 0) {
 		rxdesc = rxring->desc;
 		rxdesc += i;
 
 		if ((rxdesc->descwb.flags & cpu_to_le16(RXWBFLAG_OWN)) ||
 		!(rxdesc->descwb.desccnt & RXWBDCNT_WBCPL))
 			goto out;
+		--limit;
 
 		desccnt = rxdesc->descwb.desccnt & RXWBDCNT_DCNT;
 

drivers/net/pcmcia/3c574_cs.c

@@ -1035,7 +1035,8 @@ static int el3_rx(struct net_device *dev, int worklimit)
 	DEBUG(3, "%s: in rx_packet(), status %4.4x, rx_status %4.4x.\n",
 		  dev->name, inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus));
 	while (!((rx_status = inw(ioaddr + RxStatus)) & 0x8000) &&
-		   (--worklimit >= 0)) {
+			worklimit > 0) {
+		worklimit--;
 		if (rx_status & 0x4000) { /* Error, update stats. */
 			short error = rx_status & 0x3800;
 			dev->stats.rx_errors++;

drivers/net/pcmcia/3c589_cs.c

@@ -857,7 +857,8 @@ static int el3_rx(struct net_device *dev)
     DEBUG(3, "%s: in rx_packet(), status %4.4x, rx_status %4.4x.\n",
 	  dev->name, inw(ioaddr+EL3_STATUS), inw(ioaddr+RX_STATUS));
     while (!((rx_status = inw(ioaddr + RX_STATUS)) & 0x8000) &&
-	   (--worklimit >= 0)) {
+		    worklimit > 0) {
+	worklimit--;
 	if (rx_status & 0x4000) { /* Error, update stats. */
 	    short error = rx_status & 0x3800;
 	    dev->stats.rx_errors++;

drivers/net/smc911x.h

@@ -42,6 +42,16 @@
   #define SMC_USE_16BIT		0
   #define SMC_USE_32BIT		1
   #define SMC_IRQ_SENSE		IRQF_TRIGGER_LOW
+#elif defined(CONFIG_ARCH_OMAP34XX)
+  #define SMC_USE_16BIT		0
+  #define SMC_USE_32BIT		1
+  #define SMC_IRQ_SENSE		IRQF_TRIGGER_LOW
+  #define SMC_MEM_RESERVED	1
+#elif defined(CONFIG_ARCH_OMAP24XX)
+  #define SMC_USE_16BIT		0
+  #define SMC_USE_32BIT		1
+  #define SMC_IRQ_SENSE		IRQF_TRIGGER_LOW
+  #define SMC_MEM_RESERVED	1
 #else
 /*
  * Default configuration
@@ -675,6 +685,7 @@ smc_pxa_dma_outsl(struct smc911x_local *lp, u_long physaddr,
 #define CHIP_9116	0x0116
 #define CHIP_9117	0x0117
 #define CHIP_9118	0x0118
+#define CHIP_9211	0x9211
 #define CHIP_9215	0x115A
 #define CHIP_9217	0x117A
 #define CHIP_9218	0x118A
@@ -689,6 +700,7 @@ static const struct chip_id chip_ids[] =  {
 	{ CHIP_9116, "LAN9116" },
 	{ CHIP_9117, "LAN9117" },
 	{ CHIP_9118, "LAN9118" },
+	{ CHIP_9211, "LAN9211" },
 	{ CHIP_9215, "LAN9215" },
 	{ CHIP_9217, "LAN9217" },
 	{ CHIP_9218, "LAN9218" },

drivers/net/sungem.c

@@ -1229,7 +1229,7 @@ static void gem_reset(struct gem *gp)
 			break;
 	} while (val & (GREG_SWRST_TXRST | GREG_SWRST_RXRST));
 
-	if (limit <= 0)
+	if (limit < 0)
 		printk(KERN_ERR "%s: SW reset is ghetto.\n", gp->dev->name);
 
 	if (gp->phy_type == phy_serialink || gp->phy_type == phy_serdes)

drivers/net/tg3.c

@@ -1473,7 +1473,8 @@ static void tg3_phy_toggle_apd(struct tg3 *tp, bool enable)
 {
 	u32 reg;
 
-	if (!(tp->tg3_flags2 & TG3_FLG2_5705_PLUS))
+	if (!(tp->tg3_flags2 & TG3_FLG2_5705_PLUS) ||
+	    GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5906)
 		return;
 
 	reg = MII_TG3_MISC_SHDW_WREN |

drivers/net/tokenring/tmspci.c

@@ -121,11 +121,6 @@ static int __devinit tms_pci_attach(struct pci_dev *pdev, const struct pci_devic
 		goto err_out_trdev;
 	}
 
-	ret = request_irq(pdev->irq, tms380tr_interrupt, IRQF_SHARED,
-			  dev->name, dev);
-	if (ret)
-		goto err_out_region;
-
 	dev->base_addr	= pci_ioaddr;
 	dev->irq 	= pci_irq_line;
 	dev->dma	= 0;
@@ -142,7 +137,7 @@ static int __devinit tms_pci_attach(struct pci_dev *pdev, const struct pci_devic
 	ret = tmsdev_init(dev, &pdev->dev);
 	if (ret) {
 		printk("%s: unable to get memory for dev->priv.\n", dev->name);
-		goto err_out_irq;
+		goto err_out_region;
 	}
 
 	tp = netdev_priv(dev);
@@ -157,6 +152,11 @@ static int __devinit tms_pci_attach(struct pci_dev *pdev, const struct pci_devic
 
 	tp->tmspriv = cardinfo;
 
+	ret = request_irq(pdev->irq, tms380tr_interrupt, IRQF_SHARED,
+			  dev->name, dev);
+	if (ret)
+		goto err_out_tmsdev;
+
 	dev->open = tms380tr_open;
 	dev->stop = tms380tr_close;
 	pci_set_drvdata(pdev, dev);
@@ -164,15 +164,15 @@ static int __devinit tms_pci_attach(struct pci_dev *pdev, const struct pci_devic
 
 	ret = register_netdev(dev);
 	if (ret)
-		goto err_out_tmsdev;
+		goto err_out_irq;
 	
 	return 0;
 
+err_out_irq:
+	free_irq(pdev->irq, dev);
 err_out_tmsdev:
 	pci_set_drvdata(pdev, NULL);
 	tmsdev_term(dev);
-err_out_irq:
-	free_irq(pdev->irq, dev);
 err_out_region:
 	release_region(pci_ioaddr, TMS_PCI_IO_EXTENT);
 err_out_trdev:

drivers/net/ucc_geth_mii.c

@@ -107,7 +107,7 @@ int uec_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
 static int uec_mdio_reset(struct mii_bus *bus)
 {
 	struct ucc_mii_mng __iomem *regs = (void __iomem *)bus->priv;
-	unsigned int timeout = PHY_INIT_TIMEOUT;
+	int timeout = PHY_INIT_TIMEOUT;
 
 	mutex_lock(&bus->mdio_lock);
 
@@ -123,7 +123,7 @@ static int uec_mdio_reset(struct mii_bus *bus)
 
 	mutex_unlock(&bus->mdio_lock);
 
-	if (timeout <= 0) {
+	if (timeout < 0) {
 		printk(KERN_ERR "%s: The MII Bus is stuck!\n", bus->name);
 		return -EBUSY;
 	}

drivers/net/usb/dm9601.c

@@ -633,6 +633,10 @@ static const struct usb_device_id products[] = {
 	 },
 	{
 	USB_DEVICE(0x0a47, 0x9601),	/* Hirose USB-100 */
+	.driver_info = (unsigned long)&dm9601_info,
+	 },
+	{
+	USB_DEVICE(0x0fe6, 0x8101),	/* DM9601 USB to Fast Ethernet Adapter */
 	.driver_info = (unsigned long)&dm9601_info,
 	 },
 	{},			// END