Merge tag 'net-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
 "This is again significantly bigger than the same point into the
  previous cycle, but at least smaller than last week.

  I'm not aware of any pending regression for the current cycle.

  Including fixes from netfilter.

  Current release - regressions:

    - netfilter: walk fib6_siblings under RCU

  Previous releases - regressions:

    - netlink: fix sending unassigned nsid after assigned one

    - bridge: fix sleep in atomic context in netlink path

    - sched: fix ethx:ingress -> ethy:egress -> ethx:ingress mirred loop

    - ipv4: fix net->ipv4.sysctl_local_reserved_ports UaF

    - eth: tun: free page on short-frame rejection in tun_xdp_one()

  Previous releases - always broken:

    - skbuff: fix missing zerocopy reference in pskb_carve helpers

    - handshake: drain pending requests at net namespace exit

    - ethtool:
       - rss: avoid modifying the RSS context response
       - module: avoid leaking a netdev ref on module flash errors
       - coalesce: cap profile updates at NET_DIM_PARAMS_NUM_PROFILES

    - netfilter: fix dst corruption in same register operation

    - nfc: hci: fix out-of-bounds read in HCP header parsing

    - ipv6: exthdrs: refresh nh pointer after ipv6_hop_jumbo()

    - eth:
       - vti: use ip6_tnl.net in vti6_changelink().
       - vxlan: do not reuse cached ip_hdr() value after
         skb_tunnel_check_pmtu()"

* tag 'net-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
  dpll: zl3073x: make frequency monitor a per-device attribute
  dpll: zl3073x: use __dpll_device_change_ntf() and remove change_work
  dpll: export __dpll_device_change_ntf() for use under dpll_lock
  net/handshake: Drain pending requests at net namespace exit
  net/handshake: Verify file-reference balance in submit paths
  net/handshake: Close the submit-side sock_hold race
  net/handshake: hand off the pinned file reference to accept_doit
  net/handshake: Take a long-lived file reference at submit
  net/handshake: Pass negative errno through handshake_complete()
  nvme-tcp: store negative errno in queue->tls_err
  net/handshake: Use spin_lock_bh for hn_lock
  net: skbuff: fix missing zerocopy reference in pskb_carve helpers
  net: hibmcge: move dma_rmb() after dma_sync_single_for_cpu() in RX path
  net: hibmcge: disable Relaxed Ordering to fix RX packet corruption
  selftests/tc-testing: Add netem test case exercising loops
  selftests/tc-testing: Add mirred test cases exercising loops
  net/sched: act_mirred: Fix return code in early mirred redirect error paths
  net/sched: act_mirred: Fix blockcast recursion bypass leading to stack overflow
  net/sched: Fix ethx:ingress -> ethy:egress -> ethx:ingress mirred loop
  net/sched: fix packet loop on netem when duplicate is on
  ...

Documentation/netlink/specs/handshake.yaml

@@ -12,6 +12,12 @@ protocol: genetlink
 doc: Netlink protocol to request a transport layer security handshake.
 
 definitions:
+  -
+    type: const
+    name: max-errno
+    value: 4095
+    header: linux/err.h
+    scope: kernel
   -
     type: enum
     name: handler-class
@@ -80,6 +86,8 @@ attribute-sets:
       -
         name: status
         type: u32
+        checks:
+          max: max-errno
       -
         name: sockfd
         type: s32

drivers/dpll/dpll_netlink.c

@@ -829,12 +829,21 @@ int dpll_device_delete_ntf(struct dpll_device *dpll)
 	return dpll_device_event_send(DPLL_CMD_DEVICE_DELETE_NTF, dpll);
 }
 
-static int
-__dpll_device_change_ntf(struct dpll_device *dpll)
+/**
+ * __dpll_device_change_ntf - notify that the dpll device has been changed
+ * @dpll: registered dpll pointer
+ *
+ * Context: caller must hold dpll_lock. Suitable for use inside device
+ *          callbacks which are already invoked under dpll_lock.
+ * Return: 0 if succeeds, error code otherwise.
+ */
+int __dpll_device_change_ntf(struct dpll_device *dpll)
 {
+	lockdep_assert_held(&dpll_lock);
 	dpll_device_notify(dpll, DPLL_DEVICE_CHANGED);
 	return dpll_device_event_send(DPLL_CMD_DEVICE_CHANGE_NTF, dpll);
 }
+EXPORT_SYMBOL_GPL(__dpll_device_change_ntf);
 
 /**
  * dpll_device_change_ntf - notify that the dpll device has been changed

drivers/dpll/zl3073x/core.c

@@ -762,18 +762,15 @@ zl3073x_dev_periodic_work(struct kthread_work *work)
 		dev_warn(zldev->dev, "Failed to update phase offsets: %pe\n",
 			 ERR_PTR(rc));
 
-	/* Update measured input reference frequencies if any DPLL has
-	 * frequency monitoring enabled.
+	/* Update measured input reference frequencies if frequency
+	 * monitoring is enabled.
 	 */
-	list_for_each_entry(zldpll, &zldev->dplls, list) {
-		if (zldpll->freq_monitor) {
-			rc = zl3073x_ref_freq_meas_update(zldev);
-			if (rc)
-				dev_warn(zldev->dev,
-					 "Failed to update measured frequencies: %pe\n",
-					 ERR_PTR(rc));
-			break;
-		}
+	if (zldev->freq_monitor) {
+		rc = zl3073x_ref_freq_meas_update(zldev);
+		if (rc)
+			dev_warn(zldev->dev,
+				 "Failed to update measured frequencies: %pe\n",
+				 ERR_PTR(rc));
 	}
 
 	/* Update references' fractional frequency offsets */

drivers/dpll/zl3073x/core.h

@@ -57,6 +57,7 @@ struct zl3073x_chip_info {
  * @work: periodic work
  * @clock_id: clock id of the device
  * @phase_avg_factor: phase offset measurement averaging factor
+ * @freq_monitor: is frequency monitor enabled
  */
 struct zl3073x_dev {
 	struct device			*dev;
@@ -77,9 +78,10 @@ struct zl3073x_dev {
 	struct kthread_worker		*kworker;
 	struct kthread_delayed_work	work;
 
-	/* Devlink parameters */
+	/* Per-chip parameters */
 	u64			clock_id;
 	u8			phase_avg_factor;
+	bool			freq_monitor;
 };
 
 extern const struct regmap_config zl3073x_regmap_config;

drivers/dpll/zl3073x/dpll.c

@@ -1079,15 +1079,6 @@ zl3073x_dpll_phase_offset_avg_factor_get(const struct dpll_device *dpll,
 	return 0;
 }
 
-static void
-zl3073x_dpll_change_work(struct work_struct *work)
-{
-	struct zl3073x_dpll *zldpll;
-
-	zldpll = container_of(work, struct zl3073x_dpll, change_work);
-	dpll_device_change_ntf(zldpll->dpll_dev);
-}
-
 static int
 zl3073x_dpll_phase_offset_avg_factor_set(const struct dpll_device *dpll,
 					 void *dpll_priv, u32 factor,
@@ -1113,8 +1104,10 @@ zl3073x_dpll_phase_offset_avg_factor_set(const struct dpll_device *dpll,
 	 * we have to send a notification for other DPLL devices.
 	 */
 	list_for_each_entry(item, &zldpll->dev->dplls, list) {
-		if (item != zldpll)
-			schedule_work(&item->change_work);
+		struct dpll_device *dpll_dev = READ_ONCE(item->dpll_dev);
+
+		if (item != zldpll && dpll_dev)
+			__dpll_device_change_ntf(dpll_dev);
 	}
 
 	return 0;
@@ -1219,7 +1212,7 @@ zl3073x_dpll_freq_monitor_get(const struct dpll_device *dpll,
 {
 	struct zl3073x_dpll *zldpll = dpll_priv;
 
-	if (zldpll->freq_monitor)
+	if (zldpll->dev->freq_monitor)
 		*state = DPLL_FEATURE_STATE_ENABLE;
 	else
 		*state = DPLL_FEATURE_STATE_DISABLE;
@@ -1233,9 +1226,19 @@ zl3073x_dpll_freq_monitor_set(const struct dpll_device *dpll,
 			      enum dpll_feature_state state,
 			      struct netlink_ext_ack *extack)
 {
-	struct zl3073x_dpll *zldpll = dpll_priv;
+	struct zl3073x_dpll *item, *zldpll = dpll_priv;
 
-	zldpll->freq_monitor = (state == DPLL_FEATURE_STATE_ENABLE);
+	zldpll->dev->freq_monitor = (state == DPLL_FEATURE_STATE_ENABLE);
+
+	/* The frequency monitoring is common for all DPLL channels so after
+	 * change we have to send a notification for other DPLL devices.
+	 */
+	list_for_each_entry(item, &zldpll->dev->dplls, list) {
+		struct dpll_device *dpll_dev = READ_ONCE(item->dpll_dev);
+
+		if (item != zldpll && dpll_dev)
+			__dpll_device_change_ntf(dpll_dev);
+	}
 
 	return 0;
 }
@@ -1627,13 +1630,13 @@ zl3073x_dpll_device_register(struct zl3073x_dpll *zldpll)
 static void
 zl3073x_dpll_device_unregister(struct zl3073x_dpll *zldpll)
 {
-	WARN(!zldpll->dpll_dev, "DPLL device is not registered\n");
+	struct dpll_device *dpll_dev = READ_ONCE(zldpll->dpll_dev);
 
-	cancel_work_sync(&zldpll->change_work);
+	WARN(!dpll_dev, "DPLL device is not registered\n");
 
-	dpll_device_unregister(zldpll->dpll_dev, &zldpll->ops, zldpll);
-	dpll_device_put(zldpll->dpll_dev, &zldpll->tracker);
-	zldpll->dpll_dev = NULL;
+	WRITE_ONCE(zldpll->dpll_dev, NULL);
+	dpll_device_unregister(dpll_dev, &zldpll->ops, zldpll);
+	dpll_device_put(dpll_dev, &zldpll->tracker);
 }
 
 /**
@@ -1752,7 +1755,7 @@ zl3073x_dpll_pin_measured_freq_check(struct zl3073x_dpll_pin *pin)
 	u8 ref_id;
 	u32 freq;
 
-	if (!zldpll->freq_monitor)
+	if (!zldpll->dev->freq_monitor)
 		return false;
 
 	ref_id = zl3073x_input_pin_ref_get(pin->id);
@@ -1785,10 +1788,8 @@ zl3073x_dpll_changes_check(struct zl3073x_dpll *zldpll)
 	struct zl3073x_dev *zldev = zldpll->dev;
 	enum dpll_lock_status lock_status;
 	struct device *dev = zldev->dev;
-	const struct zl3073x_chan *chan;
 	struct zl3073x_dpll_pin *pin;
 	int rc;
-	u8 mode;
 
 	zldpll->check_count++;
 
@@ -1807,15 +1808,6 @@ zl3073x_dpll_changes_check(struct zl3073x_dpll *zldpll)
 		dpll_device_change_ntf(zldpll->dpll_dev);
 	}
 
-	/* Input pin monitoring does make sense only in automatic
-	 * or forced reference modes.
-	 */
-	chan = zl3073x_chan_state_get(zldev, zldpll->id);
-	mode = zl3073x_chan_mode_get(chan);
-	if (mode != ZL_DPLL_MODE_REFSEL_MODE_AUTO &&
-	    mode != ZL_DPLL_MODE_REFSEL_MODE_REFLOCK)
-		return;
-
 	/* Update phase offset latch registers for this DPLL if the phase
 	 * offset monitor feature is enabled.
 	 */
@@ -1926,7 +1918,6 @@ zl3073x_dpll_alloc(struct zl3073x_dev *zldev, u8 ch)
 	zldpll->dev = zldev;
 	zldpll->id = ch;
 	INIT_LIST_HEAD(&zldpll->pins);
-	INIT_WORK(&zldpll->change_work, zl3073x_dpll_change_work);
 
 	return zldpll;
 }

drivers/dpll/zl3073x/dpll.h

@@ -15,13 +15,11 @@
  * @id: DPLL index
  * @check_count: periodic check counter
  * @phase_monitor: is phase offset monitor enabled
- * @freq_monitor: is frequency monitor enabled
  * @ops: DPLL device operations for this instance
  * @dpll_dev: pointer to registered DPLL device
  * @tracker: tracking object for the acquired reference
  * @lock_status: last saved DPLL lock status
  * @pins: list of pins
- * @change_work: device change notification work
  */
 struct zl3073x_dpll {
 	struct list_head		list;
@@ -29,13 +27,11 @@ struct zl3073x_dpll {
 	u8				id;
 	u8				check_count;
 	bool				phase_monitor;
-	bool				freq_monitor;
 	struct dpll_device_ops		ops;
 	struct dpll_device		*dpll_dev;
 	dpll_tracker			tracker;
 	enum dpll_lock_status		lock_status;
 	struct list_head		pins;
-	struct work_struct		change_work;
 };
 
 struct zl3073x_dpll *zl3073x_dpll_alloc(struct zl3073x_dev *zldev, u8 ch);

drivers/net/bonding/bond_main.c

@@ -1890,6 +1890,12 @@ int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev,
 	struct sockaddr_storage ss;
 	int res = 0, i;
 
+	if (slave_dev->type == ARPHRD_CAN) {
+		BOND_NL_ERR(bond_dev, extack,
+			    "CAN devices cannot be enslaved");
+		return -EPERM;
+	}
+
 	if (slave_dev->flags & IFF_MASTER &&
 	    !netif_is_bond_master(slave_dev)) {
 		BOND_NL_ERR(bond_dev, extack,

drivers/net/ethernet/hisilicon/hibmcge/hbg_main.c

@@ -420,6 +420,9 @@ static int hbg_pci_init(struct pci_dev *pdev)
 		return -ENOMEM;
 
 	pci_set_master(pdev);
+	pcie_capability_clear_word(pdev, PCI_EXP_DEVCTL,
+				   PCI_EXP_DEVCTL_RELAX_EN);
+	pci_save_state(pdev);
 	return 0;
 }
 

drivers/net/ethernet/hisilicon/hibmcge/hbg_txrx.c

@@ -452,12 +452,12 @@ static bool hbg_sync_data_from_hw(struct hbg_priv *priv,
 {
 	struct hbg_rx_desc *rx_desc;
 
-	/* make sure HW write desc complete */
-	dma_rmb();
-
 	dma_sync_single_for_cpu(&priv->pdev->dev, buffer->page_dma,
 				buffer->page_size, DMA_FROM_DEVICE);
 
+	/* make sure HW write desc complete */
+	dma_rmb();
+
 	rx_desc = (struct hbg_rx_desc *)buffer->page_addr;
 	return FIELD_GET(HBG_RX_DESC_W2_PKT_LEN_M, rx_desc->word2) != 0;
 }

drivers/net/ethernet/marvell/octeontx2/af/rvu.c

@@ -436,7 +436,7 @@ struct rvu_pfvf *rvu_get_pfvf(struct rvu *rvu, int pcifunc)
 		return &rvu->pf[rvu_get_pf(rvu->pdev, pcifunc)];
 }
 
-static bool is_pf_func_valid(struct rvu *rvu, u16 pcifunc)
+bool is_pf_func_valid(struct rvu *rvu, u16 pcifunc)
 {
 	int pf, vf, nvfs;
 	u64 cfg;

drivers/net/ethernet/marvell/octeontx2/af/rvu.h

@@ -917,6 +917,7 @@ u16 rvu_get_rsrc_mapcount(struct rvu_pfvf *pfvf, int blkaddr);
 struct rvu_pfvf *rvu_get_pfvf(struct rvu *rvu, int pcifunc);
 void rvu_get_pf_numvfs(struct rvu *rvu, int pf, int *numvfs, int *hwvf);
 bool is_block_implemented(struct rvu_hwinfo *hw, int blkaddr);
+bool is_pf_func_valid(struct rvu *rvu, u16 pcifunc);
 bool is_pffunc_map_valid(struct rvu *rvu, u16 pcifunc, int blktype);
 int rvu_get_lf(struct rvu *rvu, struct rvu_block *block, u16 pcifunc, u16 slot);
 int rvu_lf_reset(struct rvu *rvu, struct rvu_block *block, int lf);

drivers/net/ethernet/marvell/octeontx2/af/rvu_rep.c

@@ -97,6 +97,14 @@ int rvu_mbox_handler_rep_event_notify(struct rvu *rvu, struct rep_event *req,
 {
 	struct rep_evtq_ent *qentry;
 
+	/* The mailbox dispatcher normalises only the header pcifunc; the
+	 * nested struct rep_event::pcifunc body field is sender-controlled
+	 * and is later used by rvu_rep_up_notify() to index rvu->pf[] /
+	 * rvu->hwvf[].  Reject out-of-range body selectors before queueing.
+	 */
+	if (!is_pf_func_valid(rvu, req->pcifunc))
+		return -EINVAL;
+
 	qentry = kmalloc_obj(*qentry, GFP_ATOMIC);
 	if (!qentry)
 		return -ENOMEM;

drivers/net/ethernet/mellanox/mlx5/core/steering/hws/fs_hws.c

@@ -1320,8 +1320,10 @@ mlx5_cmd_hws_packet_reformat_alloc(struct mlx5_flow_root_namespace *ns,
 		break;
 	case MLX5_REFORMAT_TYPE_REMOVE_HDR:
 		hws_action = mlx5_fs_get_action_remove_header_vlan(fs_ctx, params);
-		if (!hws_action)
+		if (!hws_action) {
 			mlx5_core_err(dev, "Only vlan remove header supported\n");
+			return -EOPNOTSUPP;
+		}
 		break;
 	default:
 		mlx5_core_err(ns->dev, "Packet-reformat not supported(%d)\n",

drivers/net/macsec.c

@@ -808,7 +808,8 @@ static bool macsec_post_decrypt(struct sk_buff *skb, struct macsec_secy *secy, u
 		if (pn + 1 > rx_sa->next_pn_halves.lower) {
 			rx_sa->next_pn_halves.lower = pn + 1;
 		} else if (secy->xpn &&
-			   !pn_same_half(pn, rx_sa->next_pn_halves.lower)) {
+			   (pn + 1 == 0 ||
+			    !pn_same_half(pn, rx_sa->next_pn_halves.lower))) {
 			rx_sa->next_pn_halves.upper++;
 			rx_sa->next_pn_halves.lower = pn + 1;
 		}

drivers/net/phy/air_en8811h.c

@@ -17,6 +17,7 @@
 #include <linux/phy.h>
 #include <linux/phy/phy-common-props.h>
 #include <linux/firmware.h>
+#include <linux/bitfield.h>
 #include <linux/property.h>
 #include <linux/wordpart.h>
 #include <linux/unaligned.h>
@@ -170,9 +171,23 @@
 #define   AN8811HB_CLK_DRV_CKO_LDPWD		BIT(13)
 #define   AN8811HB_CLK_DRV_CKO_LPPWD		BIT(14)
 
+#define AN8811HB_MCU_SW_RST		0x5cf9f8
+#define   AN8811HB_MCU_SW_RST_HOLD		BIT(16)
+#define   AN8811HB_MCU_SW_RST_RUN		(BIT(16) | BIT(0))
+#define AN8811HB_MCU_SW_START		0x5cf9fc
+#define   AN8811HB_MCU_SW_START_EN		BIT(16)
+
+/* MII register constants for PBUS access (PHY addr + 8) */
+#define AIR_PBUS_ADDR_HIGH		0x1c
+#define AIR_PBUS_DATA_HIGH		0x10
+#define AIR_PBUS_REG_ADDR_HIGH_MASK	GENMASK(15, 6)
+#define AIR_PBUS_REG_ADDR_LOW_MASK	GENMASK(5, 2)
+
 /* Led definitions */
 #define EN8811H_LED_COUNT	3
 
+#define EN8811H_PBUS_ADDR_OFFS	8
+
 /* Default LED setup:
  * GPIO5 <-> LED0  On: Link detected, blink Rx/Tx
  * GPIO4 <-> LED1  On: Link detected at 2500 or 1000 Mbps
@@ -201,6 +216,7 @@ struct en8811h_priv {
 	struct clk_hw		hw;
 	struct phy_device	*phydev;
 	unsigned int		cko_is_enabled;
+	struct mdio_device	*pbusdev;
 };
 
 enum {
@@ -254,6 +270,31 @@ static int air_phy_write_page(struct phy_device *phydev, int page)
 	return __phy_write(phydev, AIR_EXT_PAGE_ACCESS, page);
 }
 
+static int __air_pbus_reg_write(struct mdio_device *mdiodev,
+				u32 pbus_reg, u32 pbus_data)
+{
+	int ret;
+
+	ret = __mdiobus_write(mdiodev->bus, mdiodev->addr, AIR_EXT_PAGE_ACCESS,
+			      upper_16_bits(pbus_reg));
+	if (ret < 0)
+		return ret;
+
+	ret = __mdiobus_write(mdiodev->bus, mdiodev->addr, AIR_PBUS_ADDR_HIGH,
+			      FIELD_GET(AIR_PBUS_REG_ADDR_HIGH_MASK, pbus_reg));
+	if (ret < 0)
+		return ret;
+
+	ret = __mdiobus_write(mdiodev->bus, mdiodev->addr,
+			      FIELD_GET(AIR_PBUS_REG_ADDR_LOW_MASK, pbus_reg),
+			      lower_16_bits(pbus_data));
+	if (ret < 0)
+		return ret;
+
+	return __mdiobus_write(mdiodev->bus, mdiodev->addr, AIR_PBUS_DATA_HIGH,
+			       upper_16_bits(pbus_data));
+}
+
 static int __air_buckpbus_reg_write(struct phy_device *phydev,
 				    u32 pbus_address, u32 pbus_data)
 {
@@ -570,10 +611,67 @@ static int an8811hb_load_file(struct phy_device *phydev, const char *name,
 	return ret;
 }
 
+static int an8811hb_mcu_assert(struct phy_device *phydev)
+{
+	struct en8811h_priv *priv = phydev->priv;
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+
+	ret = __air_pbus_reg_write(priv->pbusdev, AN8811HB_MCU_SW_RST,
+				   AN8811HB_MCU_SW_RST_HOLD);
+	if (ret < 0)
+		goto unlock;
+
+	ret = __air_pbus_reg_write(priv->pbusdev, AN8811HB_MCU_SW_START, 0);
+	if (ret < 0)
+		goto unlock;
+
+	msleep(50);
+	phydev_dbg(phydev, "MCU asserted\n");
+
+unlock:
+	phy_unlock_mdio_bus(phydev);
+	return ret;
+}
+
+static int an8811hb_mcu_deassert(struct phy_device *phydev)
+{
+	struct en8811h_priv *priv = phydev->priv;
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+
+	ret = __air_pbus_reg_write(priv->pbusdev, AN8811HB_MCU_SW_START,
+				   AN8811HB_MCU_SW_START_EN);
+	if (ret < 0)
+		goto unlock;
+
+	ret = __air_pbus_reg_write(priv->pbusdev, AN8811HB_MCU_SW_RST,
+				   AN8811HB_MCU_SW_RST_RUN);
+	if (ret < 0)
+		goto unlock;
+
+	msleep(50);
+	phydev_dbg(phydev, "MCU deasserted\n");
+
+unlock:
+	phy_unlock_mdio_bus(phydev);
+	return ret;
+}
+
 static int an8811hb_load_firmware(struct phy_device *phydev)
 {
 	int ret;
 
+	ret = an8811hb_mcu_assert(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = an8811hb_mcu_deassert(phydev);
+	if (ret < 0)
+		return ret;
+
 	ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1,
 				     EN8811H_FW_CTRL_1_START);
 	if (ret < 0)
@@ -662,6 +760,16 @@ static int en8811h_restart_mcu(struct phy_device *phydev)
 {
 	int ret;
 
+	if (phy_id_compare_model(phydev->phy_id, AN8811HB_PHY_ID)) {
+		ret = an8811hb_mcu_assert(phydev);
+		if (ret < 0)
+			return ret;
+
+		ret = an8811hb_mcu_deassert(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
 	ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1,
 				     EN8811H_FW_CTRL_1_START);
 	if (ret < 0)
@@ -1166,6 +1274,7 @@ static int en8811h_leds_setup(struct phy_device *phydev)
 
 static int an8811hb_probe(struct phy_device *phydev)
 {
+	struct mdio_device *mdiodev;
 	struct en8811h_priv *priv;
 	int ret;
 
@@ -1175,10 +1284,28 @@ static int an8811hb_probe(struct phy_device *phydev)
 		return -ENOMEM;
 	phydev->priv = priv;
 
+	/*
+	 * The AN8811HB PHY address is restricted to 8-15 (decimal),
+	 * depending on the board hardware strapping.
+	 * This means the PBUS address is only in the range 16-21 (decimal),
+	 * so we do not need to handle the case
+	 * where the PBUS address exceeds 31 (decimal).
+	 */
+	mdiodev = mdio_device_create(phydev->mdio.bus,
+				     phydev->mdio.addr + EN8811H_PBUS_ADDR_OFFS);
+	if (IS_ERR(mdiodev))
+		return PTR_ERR(mdiodev);
+
+	ret = mdio_device_register(mdiodev);
+	if (ret)
+		goto err_dev_free;
+
+	priv->pbusdev = mdiodev;
+
 	ret = an8811hb_load_firmware(phydev);
 	if (ret < 0) {
 		phydev_err(phydev, "Load firmware failed: %d\n", ret);
-		return ret;
+		goto err_dev_create;
 	}
 
 	en8811h_print_fw_version(phydev);
@@ -1191,22 +1318,29 @@ static int an8811hb_probe(struct phy_device *phydev)
 
 	ret = en8811h_leds_setup(phydev);
 	if (ret < 0)
-		return ret;
+		goto err_dev_create;
 
 	priv->phydev = phydev;
 	/* Co-Clock Output */
 	ret = an8811hb_clk_provider_setup(&phydev->mdio.dev, &priv->hw);
 	if (ret)
-		return ret;
+		goto err_dev_create;
 
 	/* Configure led gpio pins as output */
 	ret = air_buckpbus_reg_modify(phydev, AN8811HB_GPIO_OUTPUT,
 				      AN8811HB_GPIO_OUTPUT_345,
 				      AN8811HB_GPIO_OUTPUT_345);
 	if (ret < 0)
-		return ret;
+		goto err_dev_create;
 
 	return 0;
+
+err_dev_create:
+	mdio_device_remove(mdiodev);
+
+err_dev_free:
+	mdio_device_free(mdiodev);
+	return ret;
 }
 
 static int en8811h_probe(struct phy_device *phydev)
@@ -1561,6 +1695,16 @@ static int en8811h_suspend(struct phy_device *phydev)
 	return genphy_suspend(phydev);
 }
 
+static void an8811hb_remove(struct phy_device *phydev)
+{
+	struct en8811h_priv *priv = phydev->priv;
+
+	if (priv->pbusdev) {
+		mdio_device_remove(priv->pbusdev);
+		mdio_device_free(priv->pbusdev);
+	}
+}
+
 static struct phy_driver en8811h_driver[] = {
 {
 	PHY_ID_MATCH_MODEL(EN8811H_PHY_ID),
@@ -1587,6 +1731,7 @@ static struct phy_driver en8811h_driver[] = {
 	PHY_ID_MATCH_MODEL(AN8811HB_PHY_ID),
 	.name			= "Airoha AN8811HB",
 	.probe			= an8811hb_probe,
+	.remove			= an8811hb_remove,
 	.get_features		= en8811h_get_features,
 	.config_init		= an8811hb_config_init,
 	.get_rate_matching	= en8811h_get_rate_matching,

drivers/net/tap.c

@@ -1052,6 +1052,7 @@ static int tap_get_user_xdp(struct tap_queue *q, struct xdp_buff *xdp)
 	int err, depth;
 
 	if (unlikely(xdp->data_end - xdp->data < ETH_HLEN)) {
+		put_page(virt_to_head_page(xdp->data));
 		err = -EINVAL;
 		goto err;
 	}
@@ -1061,6 +1062,7 @@ static int tap_get_user_xdp(struct tap_queue *q, struct xdp_buff *xdp)
 
 	skb = build_skb(xdp->data_hard_start, buflen);
 	if (!skb) {
+		put_page(virt_to_head_page(xdp->data));
 		err = -ENOMEM;
 		goto err;
 	}

drivers/net/team/team_core.c

@@ -534,21 +534,23 @@ static void team_adjust_ops(struct team *team)
 
 	if (!team->tx_en_port_count || !team_is_mode_set(team) ||
 	    !team->mode->ops->transmit)
-		team->ops.transmit = team_dummy_transmit;
+		WRITE_ONCE(team->ops.transmit, team_dummy_transmit);
 	else
-		team->ops.transmit = team->mode->ops->transmit;
+		WRITE_ONCE(team->ops.transmit, team->mode->ops->transmit);
 
 	if (!team->rx_en_port_count || !team_is_mode_set(team) ||
 	    !team->mode->ops->receive)
-		team->ops.receive = team_dummy_receive;
+		WRITE_ONCE(team->ops.receive, team_dummy_receive);
 	else
-		team->ops.receive = team->mode->ops->receive;
+		WRITE_ONCE(team->ops.receive, team->mode->ops->receive);
 }
 
 /*
- * We can benefit from the fact that it's ensured no port is present
- * at the time of mode change. Therefore no packets are in fly so there's no
- * need to set mode operations in any special way.
+ * team_change_mode() ensures no ports are present during mode change,
+ * but lockless readers can still reach team_xmit().  Avoid touching
+ * transmit/receive -- they are already set to dummies by
+ * team_adjust_ops() since no ports are enabled.  synchronize_net()
+ * drains in-flight readers before destroying old mode state.
  */
 static int __team_change_mode(struct team *team,
 			      const struct team_mode *new_mode)
@@ -557,9 +559,21 @@ static int __team_change_mode(struct team *team,
 	if (team_is_mode_set(team)) {
 		void (*exit_op)(struct team *team) = team->ops.exit;
 
-		/* Clear ops area so no callback is called any longer */
-		memset(&team->ops, 0, sizeof(struct team_mode_ops));
-		team_adjust_ops(team);
+		/* Clear cold-path ops used only under RTNL.  transmit and
+		 * receive are already dummies (no ports) so leave them
+		 * alone -- overwriting them is the source of the race.
+		 */
+		team->ops.init = NULL;
+		team->ops.exit = NULL;
+		team->ops.port_enter = NULL;
+		team->ops.port_leave = NULL;
+		team->ops.port_change_dev_addr = NULL;
+		team->ops.port_tx_disabled = NULL;
+
+		/* Wait for in-flight readers before tearing down mode
+		 * state they may reference.
+		 */
+		synchronize_net();
 
 		if (exit_op)
 			exit_op(team);
@@ -582,7 +596,12 @@ static int __team_change_mode(struct team *team,
 	}
 
 	team->mode = new_mode;
-	memcpy(&team->ops, new_mode->ops, sizeof(struct team_mode_ops));
+	team->ops.init = new_mode->ops->init;
+	team->ops.exit = new_mode->ops->exit;
+	team->ops.port_enter = new_mode->ops->port_enter;
+	team->ops.port_leave = new_mode->ops->port_leave;
+	team->ops.port_change_dev_addr = new_mode->ops->port_change_dev_addr;
+	team->ops.port_tx_disabled = new_mode->ops->port_tx_disabled;
 	team_adjust_ops(team);
 
 	return 0;
@@ -743,7 +762,7 @@ static rx_handler_result_t team_handle_frame(struct sk_buff **pskb)
 		/* allow exact match delivery for disabled ports */
 		res = RX_HANDLER_EXACT;
 	} else {
-		res = team->ops.receive(team, port, skb);
+		res = READ_ONCE(team->ops.receive)(team, port, skb);
 	}
 	if (res == RX_HANDLER_ANOTHER) {
 		struct team_pcpu_stats *pcpu_stats;
@@ -1845,7 +1864,7 @@ static netdev_tx_t team_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	tx_success = team_queue_override_transmit(team, skb);
 	if (!tx_success)
-		tx_success = team->ops.transmit(team, skb);
+		tx_success = READ_ONCE(team->ops.transmit)(team, skb);
 	if (tx_success) {
 		struct team_pcpu_stats *pcpu_stats;
 

drivers/net/tun.c

@@ -2394,8 +2394,10 @@ static int tun_xdp_one(struct tun_struct *tun,
 	bool skb_xdp = false;
 	struct page *page;
 
-	if (unlikely(datasize < ETH_HLEN))
+	if (unlikely(datasize < ETH_HLEN)) {
+		put_page(virt_to_head_page(xdp->data));
 		return -EINVAL;
+	}
 
 	xdp_prog = rcu_dereference(tun->xdp_prog);
 	if (xdp_prog) {
@@ -2437,6 +2439,7 @@ static int tun_xdp_one(struct tun_struct *tun,
 build:
 	skb = build_skb(xdp->data_hard_start, buflen);
 	if (!skb) {
+		put_page(virt_to_head_page(xdp->data));
 		ret = -ENOMEM;
 		goto out;
 	}

drivers/net/vxlan/vxlan_core.c

@@ -2531,7 +2531,7 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,
 			goto out_unlock;
 		}
 
-		tos = ip_tunnel_ecn_encap(tos, old_iph, skb);
+		tos = ip_tunnel_ecn_encap(tos, ip_hdr(skb), skb);
 		ttl = ttl ? : ip4_dst_hoplimit(&rt->dst);
 		err = vxlan_build_skb(skb, ndst, sizeof(struct iphdr),
 				      vni, md, flags, udp_sum);
@@ -2605,7 +2605,7 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,
 			goto out_unlock;
 		}
 
-		tos = ip_tunnel_ecn_encap(tos, old_iph, skb);
+		tos = ip_tunnel_ecn_encap(tos, ip_hdr(skb), skb);
 		ttl = ttl ? : ip6_dst_hoplimit(ndst);
 		skb_scrub_packet(skb, xnet);
 		err = vxlan_build_skb(skb, ndst, sizeof(struct ipv6hdr),

drivers/nfc/nxp-nci/i2c.c

@@ -16,6 +16,7 @@
 #include <linux/delay.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
+#include <linux/irq.h>
 #include <linux/module.h>
 #include <linux/nfc.h>
 #include <linux/gpio/consumer.h>
@@ -267,6 +268,7 @@ static int nxp_nci_i2c_probe(struct i2c_client *client)
 {
 	struct device *dev = &client->dev;
 	struct nxp_nci_i2c_phy *phy;
+	unsigned long irqflags;
 	int r;
 
 	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
@@ -303,9 +305,26 @@ static int nxp_nci_i2c_probe(struct i2c_client *client)
 	if (r < 0)
 		return r;
 
+	/*
+	 * ACPI platforms may report incorrect IRQ trigger types
+	 * (e.g. level-high), which can lead to interrupt storms.
+	 *
+	 * Use the historically stable rising-edge trigger for ACPI devices.
+	 *
+	 * On non-ACPI systems (e.g. Device Tree), prefer the firmware-
+	 * provided trigger type, falling back to rising-edge if not set.
+	 */
+	if (ACPI_COMPANION(dev)) {
+		irqflags = IRQF_TRIGGER_RISING;
+	} else {
+		irqflags = irq_get_trigger_type(client->irq);
+		if (!irqflags)
+			irqflags = IRQF_TRIGGER_RISING;
+	}
+
 	r = request_threaded_irq(client->irq, NULL,
 				 nxp_nci_i2c_irq_thread_fn,
-				 IRQF_ONESHOT,
+				 irqflags | IRQF_ONESHOT,
 				 NXP_NCI_I2C_DRIVER_NAME, phy);
 	if (r < 0)
 		nfc_err(&client->dev, "Unable to register IRQ handler\n");