Merge tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/PHY updates from Greg KH: "Here is the big set of USB and PHY driver patches for 5.2-rc1 There is the usual set of: - USB gadget updates - PHY driver updates and additions - USB serial driver updates and fixes - typec updates and new chips supported - mtu3 driver updates - xhci driver updates - other tiny driver updates Nothing really interesting, just constant forward progress. All of these have been in linux-next for a while with no reported issues. The usb-gadget and usb-serial trees were merged a bit "late", but both of them had been in linux-next before they got merged here last Friday" * tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits) USB: serial: f81232: implement break control USB: serial: f81232: add high baud rate support USB: serial: f81232: clear overrun flag USB: serial: f81232: fix interrupt worker not stop usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA usb: dwc3: Fix default lpm_nyet_threshold value usb: dwc3: debug: Print GET_STATUS(device) tracepoint usb: dwc3: Do core validation early on probe usb: dwc3: gadget: Set lpm_capable usb: gadget: atmel: tie wake lock to running clock usb: gadget: atmel: support USB suspend usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask dwc2: gadget: Fix completed transfer size calculation in DDMA usb: dwc2: Set lpm mode parameters depend on HW configuration usb: dwc2: Fix channel disable flow usb: dwc2: Set actual frame number for completed ISOC transfer usb: gadget: do not use __constant_cpu_to_le16 usb: dwc2: gadget: Increase descriptors count for ISOC's usb: introduce usb_ep_type_string() function usb: dwc3: move synchronize_irq() out of the spinlock protected block ...
2026-08-13 14:19:53 -07:00 · 2019-05-08 10:03:52 -07:00
parent 80f232121b 3515468a87
commit 132d68d37d
206 changed files with 12173 additions and 3318 deletions
@@ -0,0 +1,6 @@
+What:		/sys/bus/i2c/drivers/ucsi_ccg/.../do_flash
+Date:		May 2019
+Contact:	Ajay Gupta <ajayg@nvidia.com>
+Description:
+		Tell the driver for Cypress CCGx Type-C controller to attempt
+		firmware upgrade by writing [Yy1] to the file.
@@ -0,0 +1,27 @@
+What:		Raise a uevent when a USB Host Controller has died
+Date:		2019-04-17
+KernelVersion:	5.2
+Contact:	linux-usb@vger.kernel.org
+Description:	When the USB Host Controller has entered a state where it is no
+		longer functional a uevent will be raised. The uevent will
+		contain ACTION=offline and ERROR=DEAD.
+
+		Here is an example taken using udevadm monitor -p:
+
+		KERNEL[130.428945] offline  /devices/pci0000:00/0000:00:10.0/usb2 (usb)
+		ACTION=offline
+		BUSNUM=002
+		DEVNAME=/dev/bus/usb/002/001
+		DEVNUM=001
+		DEVPATH=/devices/pci0000:00/0000:00:10.0/usb2
+		DEVTYPE=usb_device
+		DRIVER=usb
+		ERROR=DEAD
+		MAJOR=189
+		MINOR=128
+		PRODUCT=1d6b/2/414
+		SEQNUM=2168
+		SUBSYSTEM=usb
+		TYPE=9/0/1
+
+Users:		chromium-os-dev@chromium.org
@@ -0,0 +1,32 @@
+Broadcom Stingray USB PHY
+
+Required properties:
+ - compatible : should be one of the listed compatibles
+	- "brcm,sr-usb-combo-phy" is combo PHY has two PHYs, one SS and one HS.
+	- "brcm,sr-usb-hs-phy" is a single HS PHY.
+ - reg: offset and length of the PHY blocks registers
+ - #phy-cells:
+   - Must be 1 for brcm,sr-usb-combo-phy as it expects one argument to indicate
+     the PHY number of two PHYs. 0 for HS PHY and 1 for SS PHY.
+   - Must be 0 for brcm,sr-usb-hs-phy.
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+	usbphy0: usb-phy@0 {
+		compatible = "brcm,sr-usb-combo-phy";
+		reg = <0x00000000 0x100>;
+		#phy-cells = <1>;
+	};
+
+	usbphy1: usb-phy@10000 {
+		compatible = "brcm,sr-usb-combo-phy";
+		reg = <0x00010000 0x100>,
+		#phy-cells = <1>;
+	};
+
+	usbphy2: usb-phy@20000 {
+		compatible = "brcm,sr-usb-hs-phy";
+		reg = <0x00020000 0x100>,
+		#phy-cells = <0>;
+	};
@@ -7,6 +7,9 @@ Required properties:
 - clocks:	phandles to the clocks for each clock listed in clock-names
 - clock-names:	must contain "phy"

+Optional properties:
+- vbus-supply: A phandle to the regulator for USB VBUS.
+
 Example:
 	usb3_phy0: phy@381f0040 {
 		compatible = "fsl,imx8mq-usb-phy";
@@ -0,0 +1,22 @@
+* Amlogic G12A USB2 PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb2-phy"
+- reg:		The base address and length of the registers
+- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
+- clocks:	a phandle to the clock of this PHY
+- clock-names:	must be "xtal"
+- resets:	a phandle to the reset line of this PHY
+- reset-names:	must be "phy"
+- phy-supply:	see phy-bindings.txt in this directory
+
+Example:
+	usb2_phy0: phy@36000 {
+		compatible = "amlogic,g12a-usb2-phy";
+		reg = <0x0 0x36000 0x0 0x2000>;
+		clocks = <&xtal>;
+		clock-names = "xtal";
+		resets = <&reset RESET_USB_PHY21>;
+		reset-names = "phy";
+		#phy-cells = <0>;
+	};
@@ -0,0 +1,22 @@
+* Amlogic G12A USB3 + PCIE Combo PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb3-pcie-phy"
+- #phys-cells:	must be 1. The cell number is used to select the phy mode
+  as defined in <dt-bindings/phy/phy.h> between PHY_TYPE_USB3 and PHY_TYPE_PCIE
+- reg:		The base address and length of the registers
+- clocks:	a phandle to the 100MHz reference clock of this PHY
+- clock-names:	must be "ref_clk"
+- resets:	phandle to the reset lines for the PHY control
+- reset-names:	must be "phy"
+
+Example:
+	usb3_pcie_phy: phy@46000 {
+		compatible = "amlogic,g12a-usb3-pcie-phy";
+		reg = <0x0 0x46000 0x0 0x2000>;
+		clocks = <&clkc CLKID_PCIE_PLL>;
+		clock-names = "ref_clk";
+		resets = <&reset RESET_PCIE_PHY>;
+		reset-names = "phy";
+		#phy-cells = <1>;
+	};
@@ -36,11 +36,20 @@ Required properties:
  - Tegra124: "nvidia,tegra124-xusb-padctl"
  - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
  - Tegra210: "nvidia,tegra210-xusb-padctl"
+  - Tegra186: "nvidia,tegra186-xusb-padctl"
 - reg: Physical base address and length of the controller's registers.
 - resets: Must contain an entry for each entry in reset-names.
 - reset-names: Must include the following entries:
  - "padctl"

+For Tegra186:
+- avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY
+  power supply. Must supply 1.8 V.
+- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
+  3.3 V.
+- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
+- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
+

 Pad nodes:
 ==========
@@ -0,0 +1,26 @@
+Hisilicon hi3660 USB PHY
+-----------------------
+
+Required properties:
+- compatible: should be "hisilicon,hi3660-usb-phy"
+- #phy-cells: must be 0
+- hisilicon,pericrg-syscon: phandle of syscon used to control phy.
+- hisilicon,pctrl-syscon: phandle of syscon used to control phy.
+- hisilicon,eye-diagram-param: parameter set for phy
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+This is a subnode of usb3_otg_bc register node.
+
+Example:
+	usb3_otg_bc: usb3_otg_bc@ff200000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0xff200000 0x0 0x1000>;
+
+		usb-phy {
+			compatible = "hisilicon,hi3660-usb-phy";
+			#phy-cells = <0>;
+			hisilicon,pericrg-syscon = <&crg_ctrl>;
+			hisilicon,pctrl-syscon = <&pctrl>;
+			hisilicon,eye-diagram-param = <0x22466e4>;
+		};
+	};
@@ -0,0 +1,38 @@
+MediaTek Universal Flash Storage (UFS) M-PHY binding
+--------------------------------------------------------
+
+UFS M-PHY nodes are defined to describe on-chip UFS M-PHY hardware macro.
+Each UFS M-PHY node should have its own node.
+
+To bind UFS M-PHY with UFS host controller, the controller node should
+contain a phandle reference to UFS M-PHY node.
+
+Required properties for UFS M-PHY nodes:
+- compatible         : Compatible list, contains the following controller:
+                       "mediatek,mt8183-ufsphy" for ufs phy
+                       persent on MT81xx chipsets.
+- reg                : Address and length of the UFS M-PHY register set.
+- #phy-cells         : This property shall be set to 0.
+- clocks             : List of phandle and clock specifier pairs.
+- clock-names        : List of clock input name strings sorted in the same
+                       order as the clocks property. Following clocks are
+                       mandatory.
+                       "unipro": Unipro core control clock.
+                       "mp": M-PHY core control clock.
+
+Example:
+
+	ufsphy: phy@11fa0000 {
+		compatible = "mediatek,mt8183-ufsphy";
+		reg = <0 0x11fa0000 0 0xc000>;
+		#phy-cells = <0>;
+
+		clocks = <&infracfg_ao INFRACFG_AO_UNIPRO_SCK_CG>,
+			 <&infracfg_ao INFRACFG_AO_UFS_MP_SAP_BCLK_CG>;
+		clock-names = "unipro", "mp";
+	};
+
+	ufshci@11270000 {
+		...
+		phys = <&ufsphy>;
+	};
@@ -11,6 +11,7 @@ Required properties:
 	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
 	       "qcom,msm8998-qmp-usb3-phy" for USB3 QMP V3 phy on msm8998,
 	       "qcom,msm8998-qmp-ufs-phy" for UFS QMP phy on msm8998,
+	       "qcom,msm8998-qmp-pcie-phy" for PCIe QMP phy on msm8998,
 	       "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
 	       "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845,
 	       "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845.
@@ -48,6 +49,8 @@ Required properties:
 			"aux", "cfg_ahb", "ref".
 		For "qcom,msm8998-qmp-ufs-phy" must contain:
 			"ref", "ref_aux".
+		For "qcom,msm8998-qmp-pcie-phy" must contain:
+			"aux", "cfg_ahb", "ref".
 		For "qcom,sdm845-qmp-usb3-phy" must contain:
 			"aux", "cfg_ahb", "ref", "com_aux".
 		For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
@@ -59,7 +62,8 @@ Required properties:
 	   one for each entry in reset-names.
 - reset-names: "phy" for reset of phy block,
 		"common" for phy common block reset,
-		"cfg" for phy's ahb cfg block reset.
+		"cfg" for phy's ahb cfg block reset,
+		"ufsphy" for the PHY reset in the UFS controller.

 		For "qcom,ipq8074-qmp-pcie-phy" must contain:
 			"phy", "common".
@@ -69,12 +73,16 @@ Required properties:
 			"phy", "common".
 		For "qcom,msm8998-qmp-usb3-phy" must contain
 			"phy", "common".
-		For "qcom,msm8998-qmp-ufs-phy": no resets are listed.
+		For "qcom,msm8998-qmp-ufs-phy": must contain:
+			"ufsphy".
+		For "qcom,msm8998-qmp-pcie-phy" must contain:
+			"phy", "common".
 		For "qcom,sdm845-qmp-usb3-phy" must contain:
 			"phy", "common".
 		For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
 			"phy", "common".
-		For "qcom,sdm845-qmp-ufs-phy": no resets are listed.
+		For "qcom,sdm845-qmp-ufs-phy": must contain:
+			"ufsphy".

 - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
 - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
@@ -7,6 +7,7 @@ Required properties:
 - compatible: "renesas,usb-phy-r8a7743" if the device is a part of R8A7743 SoC.
 	      "renesas,usb-phy-r8a7744" if the device is a part of R8A7744 SoC.
 	      "renesas,usb-phy-r8a7745" if the device is a part of R8A7745 SoC.
+	      "renesas,usb-phy-r8a77470" if the device is a part of R8A77470 SoC.
 	      "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC.
 	      "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC.
 	      "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC.
@@ -30,7 +31,7 @@ channels. These subnodes must contain the following properties:
 - #phy-cells: see phy-bindings.txt in the same directory, must be <1>.

 The phandle's argument in the PHY specifier is the USB controller selector for
-the USB channel; see the selector meanings below:
+the USB channel other than r8a77470 SoC; see the selector meanings below:

 +-----------+---------------+---------------+
 |\ Selector |               |               |
@@ -41,6 +42,16 @@ the USB channel; see the selector meanings below:
 | 2         | PCI EHCI/OHCI | xHCI          |
 +-----------+---------------+---------------+

+For r8a77470 SoC;see the selector meaning below:
+
+-----------+---------------+---------------+
+|\ Selector |               |               |
+ --------- +       0       |       1       |
+| Channel  \|               |               |
+-----------+---------------+---------------+
+| 0         | EHCI/OHCI     | HS-USB        |
+-----------+---------------+---------------+
+
 Example (Lager board):

 	usb-phy@e6590100 {
@@ -48,15 +59,53 @@ Example (Lager board):
 		reg = <0 0xe6590100 0 0x100>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clocks = <&cpg CPG_MOD 704>;
 		clock-names = "usbhs";
+		power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+		resets = <&cpg 704>;

-		usb-channel@0 {
+		usb0: usb-channel@0 {
 			reg = <0>;
 			#phy-cells = <1>;
 		};
-		usb-channel@2 {
+		usb2: usb-channel@2 {
 			reg = <2>;
 			#phy-cells = <1>;
 		};
 	};
+
+Example (iWave RZ/G1C sbc):
+
+	usbphy0: usb-phy0@e6590100 {
+		compatible = "renesas,usb-phy-r8a77470",
+			     "renesas,rcar-gen2-usb-phy";
+		reg = <0 0xe6590100 0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&cpg CPG_MOD 704>;
+		clock-names = "usbhs";
+		power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
+		resets = <&cpg 704>;
+
+		usb0: usb-channel@0 {
+			reg = <0>;
+			#phy-cells = <1>;
+		};
+	};
+
+	usbphy1: usb-phy@e6598100 {
+		compatible = "renesas,usb-phy-r8a77470",
+			     "renesas,rcar-gen2-usb-phy";
+		reg = <0 0xe6598100 0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&cpg CPG_MOD 706>;
+		clock-names = "usbhs";
+		power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
+		resets = <&cpg 706>;
+
+		usb1: usb-channel@0 {
+			reg = <0>;
+			#phy-cells = <1>;
+		};
+	};
@@ -1,10 +1,12 @@
 * Renesas R-Car generation 3 USB 2.0 PHY

 This file provides information on what the device node for the R-Car generation
-3 and RZ/G2 USB 2.0 PHY contain.
+3, RZ/G1C and RZ/G2 USB 2.0 PHY contain.

 Required properties:
- compatible: "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1
+- compatible: "renesas,usb2-phy-r8a77470" if the device is a part of an R8A77470
+	      SoC.
+	      "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1
 	      SoC.
 	      "renesas,usb2-phy-r8a774c0" if the device is a part of an R8A774C0
 	      SoC.
@@ -27,7 +29,13 @@ Required properties:

 - reg: offset and length of the partial USB 2.0 Host register block.
 - clocks: clock phandle and specifier pair(s).
- #phy-cells: see phy-bindings.txt in the same directory, must be <0>.
+- #phy-cells: see phy-bindings.txt in the same directory, must be <1> (and
+	      using <0> is deprecated).
+
+The phandle's argument in the PHY specifier is the INT_STATUS bit of controller:
+- 1 = USBH_INTA (OHCI)
+- 2 = USBH_INTB (EHCI)
+- 3 = UCOM_INT (OTG and BC)

 Optional properties:
 To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are
@@ -7,12 +7,15 @@ Required properties:
 - reg: PHY register address offset and length in "general
   register files"

-Optional clocks using the clock bindings (see ../clock/clock-bindings.txt),
-specified by name:
+Optional properties:
 - clock-names: Should contain "emmcclk".  Although this is listed as optional
 		(because most boards can get basic functionality without having
 		access to it), it is strongly suggested.
+		See ../clock/clock-bindings.txt for details.
 - clocks: Should have a phandle to the card clock exported by the SDHCI driver.
+ - drive-impedance-ohm: Specifies the drive impedance in Ohm.
+                        Possible values are 33, 40, 50, 66 and 100.
+                        If not set, the default value of 50 will be applied.

 Example:

@@ -29,6 +32,7 @@ grf: syscon@ff770000 {
 		reg = <0xf780 0x20>;
 		clocks = <&sdhci>;
 		clock-names = "emmcclk";
+		drive-impedance-ohm = <50>;
 		#phy-cells = <0>;
 	};
 };
@@ -0,0 +1,82 @@
+TI AM654 SERDES
+
+Required properties:
+ - compatible: Should be "ti,phy-am654-serdes"
+ - reg : Address and length of the register set for the device.
+ - #phy-cells: determine the number of cells that should be given in the
+	phandle while referencing this phy. Should be "2". The 1st cell
+	corresponds to the phy type (should be one of the types specified in
+	include/dt-bindings/phy/phy.h) and the 2nd cell should be the serdes
+	lane function.
+	If SERDES0 is referenced 2nd cell should be:
+		0 - USB3
+		1 - PCIe0 Lane0
+		2 - ICSS2 SGMII Lane0
+	If SERDES1 is referenced 2nd cell should be:
+		0 - PCIe1 Lane0
+		1 - PCIe0 Lane1
+		2 - ICSS2 SGMII Lane1
+ - power-domains: As documented by the generic PM domain bindings in
+	Documentation/devicetree/bindings/power/power_domain.txt.
+ - clocks: List of clock-specifiers representing the input to the SERDES.
+	Should have 3 items representing the left input clock, external
+	reference clock and right input clock in that order.
+ - clock-output-names: List of clock names for each of the clock outputs of
+	SERDES. Should have 3 items for CMU reference clock,
+	left output clock and right output clock in that order.
+ - assigned-clocks: As defined in
+	Documentation/devicetree/bindings/clock/clock-bindings.txt
+ - assigned-clock-parents: As defined in
+	Documentation/devicetree/bindings/clock/clock-bindings.txt
+ - #clock-cells: Should be <1> to choose between the 3 output clocks.
+	Defined in Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+   The following macros are defined in dt-bindings/phy/phy-am654-serdes.h
+   for selecting the correct reference clock. This can be used while
+   specifying the clocks created by SERDES.
+	=> AM654_SERDES_CMU_REFCLK
+	=> AM654_SERDES_LO_REFCLK
+	=> AM654_SERDES_RO_REFCLK
+
+ - mux-controls: Phandle to the multiplexer that is used to select the lane
+	function. See #phy-cells above to see the multiplex values.
+
+Example:
+
+Example for SERDES0 is given below. It has 3 clock inputs;
+left input reference clock as indicated by <&k3_clks 153 4>, external
+reference clock as indicated by <&k3_clks 153 1> and right input
+reference clock as indicated by <&serdes1 AM654_SERDES_LO_REFCLK>. (The
+right input of SERDES0 is connected to the left output of SERDES1).
+
+SERDES0 registers 3 clock outputs as indicated in clock-output-names. The
+first refers to the CMU reference clock, second refers to the left output
+reference clock and the third refers to the right output reference clock.
+
+The assigned-clocks and assigned-clock-parents is used here to set the
+parent of left input reference clock to MAINHSDIV_CLKOUT4 and parent of
+CMU reference clock to left input reference clock.
+
+serdes0: serdes@900000 {
+	compatible = "ti,phy-am654-serdes";
+	reg = <0x0 0x900000 0x0 0x2000>;
+	reg-names = "serdes";
+	#phy-cells = <2>;
+	power-domains = <&k3_pds 153>;
+	clocks = <&k3_clks 153 4>, <&k3_clks 153 1>,
+			<&serdes1 AM654_SERDES_LO_REFCLK>;
+	clock-output-names = "serdes0_cmu_refclk", "serdes0_lo_refclk",
+				"serdes0_ro_refclk";
+	assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
+	assigned-clock-parents = <&k3_clks 153 8>, <&k3_clks 153 4>;
+	ti,serdes-clk = <&serdes0_clk>;
+	mux-controls = <&serdes_mux 0>;
+	#clock-cells = <1>;
+};
+
+Example for PCIe consumer node using the SERDES PHY specifier is given below.
+&pcie0_rc {
+        num-lanes = <2>;
+        phys = <&serdes0 PHY_TYPE_PCIE 1>, <&serdes1 PHY_TYPE_PCIE 1>;
+        phy-names = "pcie-phy0", "pcie-phy1";
+};
@@ -29,6 +29,7 @@ Optional properties:
 - vdda-pll-max-microamp : specifies max. load that can be drawn from pll supply
 - vddp-ref-clk-supply   : phandle to UFS device ref_clk pad power supply
 - vddp-ref-clk-max-microamp : specifies max. load that can be drawn from this supply
+- resets : specifies the PHY reset in the UFS controller

 Example:

@@ -51,9 +52,11 @@ Example:
 			<&clock_gcc clk_ufs_phy_ldo>,
 			<&clock_gcc clk_gcc_ufs_tx_cfg_clk>,
 			<&clock_gcc clk_gcc_ufs_rx_cfg_clk>;
+		resets = <&ufshc 0>;
 	};

-	ufshc@fc598000 {
+	ufshc: ufshc@fc598000 {
+		#reset-cells = <1>;
 		...
 		phys = <&ufsphy1>;
 		phy-names = "ufsphy";
@@ -50,6 +50,8 @@ Optional properties:
 -lanes-per-direction	: number of lanes available per direction - either 1 or 2.
 			  Note that it is assume same number of lanes is used both
 			  directions at once. If not specified, default is 2 lanes per direction.
+- #reset-cells		: Must be <1> for Qualcomm UFS controllers that expose
+			  PHY reset from the UFS controller.
 - resets            : reset node register
 - reset-names       : describe reset node register, the "rst" corresponds to reset the whole UFS IP.

@@ -79,4 +81,5 @@ Example:
 		reset-names = "rst";
 		phys = <&ufsphy1>;
 		phy-names = "ufsphy";
+		#reset-cells = <1>;
 	};
@@ -40,3 +40,91 @@ Example device nodes:
 				phy-names = "usb2-phy", "usb3-phy";
 			};
 		};
+
+Amlogic Meson G12A DWC3 USB SoC Controller Glue
+
+The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3
+in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode
+only.
+
+A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY.
+
+One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP.
+
+The DWC3 Glue controls the PHY routing and power, an interrupt line is
+connected to the Glue to serve as OTG ID change detection.
+
+Required properties:
+- compatible:	Should be "amlogic,meson-g12a-usb-ctrl"
+- clocks:	a handle for the "USB" clock
+- resets:	a handle for the shared "USB" reset line
+- reg:		The base address and length of the registers
+- interrupts:	the interrupt specifier for the OTG detection
+- phys: 	handle to used PHYs on the system
+	- a <0> phandle can be used if a PHY is not used
+- phy-names:	names of the used PHYs on the system :
+	- "usb2-phy0" for USB2 PHY0 if USBHOST_A port is used
+	- "usb2-phy1" for USB2 PHY1 if USBOTG_B port is used
+	- "usb3-phy0" for USB3 PHY if USB3_0 is used
+- dr_mode:	should be "host", "peripheral", or "otg" depending on
+	the usage and configuration of the OTG Capable port.
+	- "host" and "peripheral" means a fixed Host or Device only connection
+	- "otg" means the port can be used as both Host or Device and
+	  be switched automatically using the OTG ID pin.
+
+Optional properties:
+- vbus-supply:	should be a phandle to the regulator controlling the VBUS
+		power supply when used in OTG switchable mode
+
+Required child nodes:
+
+A child node must exist to represent the core DWC3 IP block. The name of
+the node is not important. The content of the node is defined in dwc3.txt.
+
+A child node must exist to represent the core DWC2 IP block. The name of
+the node is not important. The content of the node is defined in dwc2.txt.
+
+PHY documentation is provided in the following places:
+- Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt
+- Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt
+
+Example device nodes:
+	usb: usb@ffe09000 {
+			compatible = "amlogic,meson-g12a-usb-ctrl";
+			reg = <0x0 0xffe09000 0x0 0xa0>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&clkc CLKID_USB>;
+			resets = <&reset RESET_USB>;
+
+			dr_mode = "otg";
+
+			phys = <&usb2_phy0>, <&usb2_phy1>,
+			       <&usb3_pcie_phy PHY_TYPE_USB3>;
+			phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
+
+			dwc2: usb@ff400000 {
+				compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+				reg = <0x0 0xff400000 0x0 0x40000>;
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+				clock-names = "ddr";
+				phys = <&usb2_phy1>;
+				dr_mode = "peripheral";
+				g-rx-fifo-size = <192>;
+				g-np-tx-fifo-size = <128>;
+				g-tx-fifo-size = <128 128 16 16 16>;
+			};
+
+			dwc3: usb@ff500000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff500000 0x0 0x100000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,dis_u2_susphy_quirk;
+				snps,quirk-frame-length-adjustment;
+			};
+	};
@@ -14,6 +14,7 @@ Required properties:
  - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs;
  - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
  - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
+  - "amlogic,meson-g12a-usb": The DWC2 USB controller instance in Amlogic G12A SoCs;
  - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs;
  - snps,dwc2: A generic DWC2 USB controller with default parameters.
  - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs
@@ -31,12 +32,18 @@ Refer to clk/clock-bindings.txt for generic clock consumer properties
 Optional properties:
 - phys: phy provider specifier
 - phy-names: shall be "usb2-phy"
+- vbus-supply: reference to the VBUS regulator. Depending on the current mode
+  this is enabled (in "host" mode") or disabled (in "peripheral" mode). The
+  regulator is updated if the controller is configured in "otg" mode and the
+  status changes between "host" and "peripheral".
 Refer to phy/phy-bindings.txt for generic phy consumer properties
 - dr_mode: shall be one of "host", "peripheral" and "otg"
  Refer to usb/generic.txt
 - g-rx-fifo-size: size of rx fifo size in gadget mode.
 - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
 - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
+- snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when
+                          we detect a wakeup.  This is due to a hardware errata.

 Deprecated properties:
 - g-use-dma: gadget DMA mode is automatically detected
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/generic-ehci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: USB EHCI Controller Device Tree Bindings
+
+allOf:
+  - $ref: "usb-hcd.yaml"
+
+maintainers:
+  - Greg Kroah-Hartman <gregkh@linuxfoundation.org>
+
+properties:
+  compatible:
+    contains:
+      const: generic-ehci
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  resets:
+    minItems: 1
+    maxItems: 4
+
+  clocks:
+    minItems: 1
+    maxItems: 4
+    description: |
+      In case the Renesas R-Car Gen3 SoCs:
+        - if a host only channel: first clock should be host.
+        - if a USB DRD channel: first clock should be host and second
+          one should be peripheral
+
+  big-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag for HCDs with big endian descriptors and big
+      endian registers.
+
+  big-endian-desc:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag for HCDs with big endian descriptors.
+
+  big-endian-regs:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag for HCDs with big endian registers.
+
+  has-transaction-translator:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag if EHCI has a Transaction Translator built into
+      the root hub.
+
+  needs-reset-on-resume:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag to force EHCI reset after resume.
+
+  phys: true
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    ehci@e0000300 {
+        compatible = "ibm,usb-ehci-440epx", "generic-ehci";
+        interrupt-parent = <&UIC0>;
+        interrupts = <0x1a 4>;
+        reg = <0 0xe0000300 90 0 0xe0000390 70>;
+        big-endian;
+    };
+
+  - |
+    ehci0: usb@1c14000 {
+        compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
+        reg = <0x01c14000 0x100>;
+        interrupts = <39>;
+        clocks = <&ahb_gates 1>;
+        phys = <&usbphy 1>;
+        phy-names = "usb";
+    };
+
+...
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/generic-ohci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: USB OHCI Controller Device Tree Bindings
+
+allOf:
+  - $ref: "usb-hcd.yaml"
+
+maintainers:
+  - Greg Kroah-Hartman <gregkh@linuxfoundation.org>
+
+properties:
+  compatible:
+    contains:
+      const: generic-ohci
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  resets:
+    minItems: 1
+    maxItems: 2
+
+  clocks:
+    minItems: 1
+    maxItems: 3
+    description: |
+      In case the Renesas R-Car Gen3 SoCs:
+        - if a host only channel: first clock should be host.
+        - if a USB DRD channel: first clock should be host and second
+          one should be peripheral
+
+  big-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag for HCDs with big endian descriptors and big
+      endian registers.
+
+  big-endian-desc:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag for HCDs with big endian descriptors.
+
+  big-endian-regs:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set this flag for HCDs with big endian registers.
+
+  remote-wakeup-connected:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Remote wakeup is wired on the platform.
+
+  no-big-frame-no:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Set if frame_no lives in bits [15:0] of HCCA
+
+  num-ports:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Overrides the detected port count
+
+  phys: true
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+      ohci0: usb@1c14400 {
+          compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
+          reg = <0x01c14400 0x100>;
+          interrupts = <64>;
+          clocks = <&usb_clk 6>, <&ahb_gates 2>;
+          phys = <&usbphy 1>;
+      };
+
+...
--- a/Show More
+++ b/Show More