Merge changes in the PM core, system-wide PM infrastructure, generic
power domains (genpd) framework, ACPI PM infrastructure and cpuidle
for 4.19.
* pm-core:
driver core: Add flag to autoremove device link on supplier unbind
driver core: Rename flag AUTOREMOVE to AUTOREMOVE_CONSUMER
* pm-domains:
PM / Domains: Introduce dev_pm_domain_attach_by_name()
PM / Domains: Introduce option to attach a device by name to genpd
PM / Domains: dt: Add a power-domain-names property
* pm-sleep:
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
x86/power/hibernate_64: Remove VLA usage
PM / hibernate: cast PAGE_SIZE to int when comparing with error code
* acpi-pm:
ACPI / PM: save NVS memory for ASUS 1025C laptop
ACPI / PM: Default to s2idle in all machines supporting LP S0
* pm-cpuidle:
ARM: cpuidle: silence error on driver registration failure
regmap: Support non-incrementing registers
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull driver core fix from Greg KH:
"This is a single driver core fix for 4.18-rc7. It partially reverts a
previous commit to resolve some reported issues.
It has been in linux-next for a while now with no reported issues"
* tag 'driver-core-4.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Partially revert "driver core: correct device's shutdown order"
There is a race window in device_shutdown(), which may cause
-1. parent device shut down before child or
-2. no shutdown on a new probing device.
For 1st, taking the following scenario:
device_shutdown new plugin device
list_del_init(parent_dev);
spin_unlock(list_lock);
device_add(child)
probe child
shutdown parent_dev
--> now child is on the tail of devices_kset
For 2nd, taking the following scenario:
device_shutdown new plugin device
device_add(dev)
device_lock(dev);
...
device_unlock(dev);
probe dev
--> now, the new occurred dev has no opportunity to shutdown
To fix this race issue, just prevent the new probing request. With this
logic, device_shutdown() is more similar to dpm_prepare().
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Plumb in get_ownership() callback for devices belonging to a class so that
they can be created with uid/gid different from global root. This will
allow network devices in a container to belong to container's root and not
global root.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds Serial Camera Control Bus (SCCB) support for regmap API that
is intended to be used by some of Omnivision sensor drivers.
The ov772x and ov9650 drivers are going to use this SCCB regmap API.
The ov772x driver was previously only worked with the i2c controller
drivers that support I2C_FUNC_PROTOCOL_MANGLING, because the ov772x
device doesn't support repeated starts. After commit 0b964d183c
("media: ov772x: allow i2c controllers without
I2C_FUNC_PROTOCOL_MANGLING"), reading ov772x register is replaced with
issuing two separated i2c messages in order to avoid repeated start.
Using this SCCB regmap hides the implementation detail.
The ov9650 driver also issues two separated i2c messages to read the
registers as the device doesn't support repeated start. So it can
make use of this SCCB regmap.
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For devices with a class, we create a "glue" directory between
the parent device and the new device with the class name.
This directory is never "explicitely" removed when empty however,
this is left to the implicit sysfs removal done by kobject_release()
when the object loses its last reference via kobject_put().
This is problematic because as long as it's not been removed from
sysfs, it is still present in the class kset and in sysfs directory
structure.
The presence in the class kset exposes a use after free bug fixed
by the previous patch, but the presence in sysfs means that until
the kobject is released, which can take a while (especially with
kobject debugging), any attempt at re-creating such as binding a
new device for that class/parent pair, will result in a sysfs
duplicate file name error.
This fixes it by instead doing an explicit kobject_del() when
the glue dir is empty, by keeping track of the number of
child devices of the gluedir.
This is made easy by the fact that all glue dir operations are
done with a global mutex, and there's already a function
(cleanup_glue_dir) called in all the right places taking that
mutex that can be enhanced for this. It appears that this was
in fact the intent of the function, but the implementation was
wrong.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SLIMbus supports upto 16 bytes in value management messages,
so add support to read/writes upto 16 bytes.
This also removes redundant single register reg_read/reg_write.
Also useful for paged register access on SLIMbus interfaced codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 52cdbdd498 (driver core: correct device's shutdown order)
introduced a regression by breaking device shutdown on some systems.
Namely, the devices_kset_move_last() call in really_probe() added by
that commit is a mistake as it may cause parents to follow children
in the devices_kset list which then causes shutdown to fail. For
example, if a device has children before really_probe() is called
for it (which is not uncommon), that call will cause it to be
reordered after the children in the devices_kset list and the
ordering of that list will not reflect the correct device shutdown
order any more.
Also it causes the devices_kset list to be constantly reordered
until all drivers have been probed which is totally pointless
overhead in the majority of cases and it only covered an issue
with system shutdown, while system-wide suspend/resume potentially
had the same issue on the affected platforms (which was not covered).
Moreover, the shutdown issue originally addressed by the change in
really_probe() made by commit 52cdbdd498 is not present in 4.18-rc
any more, since dra7 started to use the sdhci-omap driver which
doesn't disable any regulators during shutdown, so the really_probe()
part of commit 52cdbdd498 can be safely reverted. [The original
issue was related to the omap_hsmmc driver used by dra7 previously.]
For the above reasons, revert the really_probe() modifications made
by commit 52cdbdd498.
The other code changes made by commit 52cdbdd498 are useful and
they need not be reverted.
Fixes: 52cdbdd498 (driver core: correct device's shutdown order)
Link: https://lore.kernel.org/lkml/CAFgQCTt7VfqM=UyCnvNFxrSw8Z6cUtAi3HUwR4_xPAc03SgHjQ@mail.gmail.com/
Reported-by: Pingfan Liu <kernelfans@gmail.com>
Tested-by: Pingfan Liu <kernelfans@gmail.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All PM domain drivers must be built-in (at least those using DT), so
there is no point deferring probe after initcalls are done. Continuing
to defer probe may prevent booting successfully even if managing PM
domains is not required. This can happen if the user failed to enable
the driver or if power-domains are added to a platform's DT, but there
is not yet a driver (e.g. a new DTB with an old kernel).
Call the driver core function driver_deferred_probe_check_init_done()
instead of just returning -EPROBE_DEFER to stop deferring probe when
initcalls are done.
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deferred probe will currently wait forever on dependent devices to probe,
but sometimes a driver will never exist. It's also not always critical for
a driver to exist. Platforms can rely on default configuration from the
bootloader or reset defaults for things such as pinctrl and power domains.
This is often the case with initial platform support until various drivers
get enabled. There's at least 2 scenarios where deferred probe can render
a platform broken. Both involve using a DT which has more devices and
dependencies than the kernel supports. The 1st case is a driver may be
disabled in the kernel config. The 2nd case is the kernel version may
simply not have the dependent driver. This can happen if using a newer DT
(provided by firmware perhaps) with a stable kernel version. Deferred
probe issues can be difficult to debug especially if the console has
dependencies or userspace fails to boot to a shell.
There are also cases like IOMMUs where only built-in drivers are
supported, so deferring probe after initcalls is not needed. The IOMMU
subsystem implemented its own mechanism to handle this using OF_DECLARE
linker sections.
This commit adds makes ending deferred probe conditional on initcalls
being completed or a debug timeout. Subsystems or drivers may opt-in by
calling driver_deferred_probe_check_init_done() instead of
unconditionally returning -EPROBE_DEFER. They may use additional
information from DT or kernel's config to decide whether to continue to
defer probe or not.
The timeout mechanism is intended for debug purposes and WARNs loudly.
The remaining deferred probe pending list will also be dumped after the
timeout. Not that this timeout won't work for the console which needs
to be enabled before userspace starts. However, if the console's
dependencies are resolved, then the kernel log will be printed (as
opposed to no output).
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a flag to autoremove the device links on supplier driver
unbind. This obviates the need to explicitly delete the link
in the remove path.
We remove these links only when the supplier's link to its
consumers has gone to DL_STATE_SUPPLIER_UNBIND state.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Suggested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki
Mark Brown
Crestez Dan Leonard
Thomas Gleixner
David S. Miller
Greg Kroah-Hartman
Linus Torvalds
Akinobu Mita
Benjamin Gaignard
Pingfan Liu
Dmitry Torokhov
Mimi Zohar
Benjamin Herrenschmidt
Shaokun Zhang
Srinivas Kandagatla
Rob Herring
Vivek Gautam