Merge branches 'ib-mfd-leds-4.16', 'ib-mfd-memstick-misc-mmc-4.16', 'ib-mfd-platform-4.16' and 'ib-mfd-tty-watchdog-4.16', tag 'ib-extcon-mfd-4.16-1' into ibs-for-mfd-merged

Immutable branch for both MFD and EXTCON tree.

Documentation/devicetree/bindings/watchdog/zii,rave-sp-wdt.txt

@@ -0,0 +1,39 @@
+Zodiac Inflight Innovations RAVE Supervisory Processor Watchdog Bindings
+
+RAVE SP watchdog device is a "MFD cell" device corresponding to
+watchdog functionality of RAVE Supervisory Processor. It is expected
+that its Device Tree node is specified as a child of the node
+corresponding to the parent RAVE SP device (as documented in
+Documentation/devicetree/bindings/mfd/zii,rave-sp.txt)
+
+Required properties:
+
+- compatible: Depending on wire protocol implemented by RAVE SP
+  firmware, should be one of:
+	- "zii,rave-sp-watchdog"
+	- "zii,rave-sp-watchdog-legacy"
+
+Optional properties:
+
+- wdt-timeout:	Two byte nvmem cell specified as per
+		Documentation/devicetree/bindings/nvmem/nvmem.txt
+
+Example:
+
+	rave-sp {
+		compatible = "zii,rave-sp-rdu1";
+		current-speed = <38400>;
+
+		eeprom {
+			wdt_timeout: wdt-timeout@8E {
+				reg = <0x8E 2>;
+			};
+		};
+
+		watchdog {
+			compatible = "zii,rave-sp-watchdog";
+			nvmem-cells = <&wdt_timeout>;
+			nvmem-cell-names = "wdt-timeout";
+		};
+	}
+

Documentation/driver-model/devres.txt

@@ -384,6 +384,9 @@ RESET
   devm_reset_control_get()
   devm_reset_controller_register()
 
+SERDEV
+  devm_serdev_device_open()
+
 SLAVE DMA ENGINE
   devm_acpi_dma_controller_register()
 

drivers/extcon/extcon-axp288.c

@@ -24,8 +24,6 @@
 #include <linux/notifier.h>
 #include <linux/extcon-provider.h>
 #include <linux/regmap.h>
-#include <linux/gpio.h>
-#include <linux/gpio/consumer.h>
 #include <linux/mfd/axp20x.h>
 
 /* Power source status register */
@@ -79,11 +77,6 @@ enum axp288_extcon_reg {
 	AXP288_BC_DET_STAT_REG		= 0x2f,
 };
 
-enum axp288_mux_select {
-	EXTCON_GPIO_MUX_SEL_PMIC = 0,
-	EXTCON_GPIO_MUX_SEL_SOC,
-};
-
 enum axp288_extcon_irq {
 	VBUS_FALLING_IRQ = 0,
 	VBUS_RISING_IRQ,
@@ -104,10 +97,8 @@ struct axp288_extcon_info {
 	struct device *dev;
 	struct regmap *regmap;
 	struct regmap_irq_chip_data *regmap_irqc;
-	struct gpio_desc *gpio_mux_cntl;
 	int irq[EXTCON_IRQ_END];
 	struct extcon_dev *edev;
-	struct notifier_block extcon_nb;
 	unsigned int previous_cable;
 };
 
@@ -197,15 +188,6 @@ static int axp288_handle_chrg_det_event(struct axp288_extcon_info *info)
 	}
 
 no_vbus:
-	/*
-	 * If VBUS is absent Connect D+/D- lines to PMIC for BC
-	 * detection. Else connect them to SOC for USB communication.
-	 */
-	if (info->gpio_mux_cntl)
-		gpiod_set_value(info->gpio_mux_cntl,
-			vbus_attach ? EXTCON_GPIO_MUX_SEL_SOC
-					: EXTCON_GPIO_MUX_SEL_PMIC);
-
 	extcon_set_state_sync(info->edev, info->previous_cable, false);
 	if (info->previous_cable == EXTCON_CHG_USB_SDP)
 		extcon_set_state_sync(info->edev, EXTCON_USB, false);
@@ -253,8 +235,7 @@ static int axp288_extcon_probe(struct platform_device *pdev)
 {
 	struct axp288_extcon_info *info;
 	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
-	struct axp288_extcon_pdata *pdata = pdev->dev.platform_data;
-	int ret, i, pirq, gpio;
+	int ret, i, pirq;
 
 	info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
 	if (!info)
@@ -264,8 +245,6 @@ static int axp288_extcon_probe(struct platform_device *pdev)
 	info->regmap = axp20x->regmap;
 	info->regmap_irqc = axp20x->regmap_irqc;
 	info->previous_cable = EXTCON_NONE;
-	if (pdata)
-		info->gpio_mux_cntl = pdata->gpio_mux_cntl;
 
 	platform_set_drvdata(pdev, info);
 
@@ -286,21 +265,11 @@ static int axp288_extcon_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	/* Set up gpio control for USB Mux */
-	if (info->gpio_mux_cntl) {
-		gpio = desc_to_gpio(info->gpio_mux_cntl);
-		ret = devm_gpio_request(&pdev->dev, gpio, "USB_MUX");
-		if (ret < 0) {
-			dev_err(&pdev->dev,
-				"failed to request the gpio=%d\n", gpio);
-			return ret;
-		}
-		gpiod_direction_output(info->gpio_mux_cntl,
-						EXTCON_GPIO_MUX_SEL_PMIC);
-	}
-
 	for (i = 0; i < EXTCON_IRQ_END; i++) {
 		pirq = platform_get_irq(pdev, i);
+		if (pirq < 0)
+			return pirq;
+
 		info->irq[i] = regmap_irq_get_virq(info->regmap_irqc, pirq);
 		if (info->irq[i] < 0) {
 			dev_err(&pdev->dev,

drivers/extcon/extcon-usbc-cros-ec.c

@@ -34,16 +34,26 @@ struct cros_ec_extcon_info {
 
 	struct notifier_block notifier;
 
+	unsigned int dr; /* data role */
+	bool pr; /* power role (true if VBUS enabled) */
 	bool dp; /* DisplayPort enabled */
 	bool mux; /* SuperSpeed (usb3) enabled */
 	unsigned int power_type;
 };
 
 static const unsigned int usb_type_c_cable[] = {
+	EXTCON_USB,
+	EXTCON_USB_HOST,
 	EXTCON_DISP_DP,
 	EXTCON_NONE,
 };
 
+enum usb_data_roles {
+	DR_NONE,
+	DR_HOST,
+	DR_DEVICE,
+};
+
 /**
  * cros_ec_pd_command() - Send a command to the EC.
  * @info: pointer to struct cros_ec_extcon_info
@@ -150,6 +160,7 @@ static int cros_ec_usb_get_role(struct cros_ec_extcon_info *info,
 	pd_control.port = info->port_id;
 	pd_control.role = USB_PD_CTRL_ROLE_NO_CHANGE;
 	pd_control.mux = USB_PD_CTRL_MUX_NO_CHANGE;
+	pd_control.swap = USB_PD_CTRL_SWAP_NONE;
 	ret = cros_ec_pd_command(info, EC_CMD_USB_PD_CONTROL, 1,
 				 &pd_control, sizeof(pd_control),
 				 &resp, sizeof(resp));
@@ -183,11 +194,72 @@ static int cros_ec_pd_get_num_ports(struct cros_ec_extcon_info *info)
 	return resp.num_ports;
 }
 
+static const char *cros_ec_usb_role_string(unsigned int role)
+{
+	return role == DR_NONE ? "DISCONNECTED" :
+		(role == DR_HOST ? "DFP" : "UFP");
+}
+
+static const char *cros_ec_usb_power_type_string(unsigned int type)
+{
+	switch (type) {
+	case USB_CHG_TYPE_NONE:
+		return "USB_CHG_TYPE_NONE";
+	case USB_CHG_TYPE_PD:
+		return "USB_CHG_TYPE_PD";
+	case USB_CHG_TYPE_PROPRIETARY:
+		return "USB_CHG_TYPE_PROPRIETARY";
+	case USB_CHG_TYPE_C:
+		return "USB_CHG_TYPE_C";
+	case USB_CHG_TYPE_BC12_DCP:
+		return "USB_CHG_TYPE_BC12_DCP";
+	case USB_CHG_TYPE_BC12_CDP:
+		return "USB_CHG_TYPE_BC12_CDP";
+	case USB_CHG_TYPE_BC12_SDP:
+		return "USB_CHG_TYPE_BC12_SDP";
+	case USB_CHG_TYPE_OTHER:
+		return "USB_CHG_TYPE_OTHER";
+	case USB_CHG_TYPE_VBUS:
+		return "USB_CHG_TYPE_VBUS";
+	case USB_CHG_TYPE_UNKNOWN:
+		return "USB_CHG_TYPE_UNKNOWN";
+	default:
+		return "USB_CHG_TYPE_UNKNOWN";
+	}
+}
+
+static bool cros_ec_usb_power_type_is_wall_wart(unsigned int type,
+						unsigned int role)
+{
+	switch (type) {
+	/* FIXME : Guppy, Donnettes, and other chargers will be miscategorized
+	 * because they identify with USB_CHG_TYPE_C, but we can't return true
+	 * here from that code because that breaks Suzy-Q and other kinds of
+	 * USB Type-C cables and peripherals.
+	 */
+	case USB_CHG_TYPE_PROPRIETARY:
+	case USB_CHG_TYPE_BC12_DCP:
+		return true;
+	case USB_CHG_TYPE_PD:
+	case USB_CHG_TYPE_C:
+	case USB_CHG_TYPE_BC12_CDP:
+	case USB_CHG_TYPE_BC12_SDP:
+	case USB_CHG_TYPE_OTHER:
+	case USB_CHG_TYPE_VBUS:
+	case USB_CHG_TYPE_UNKNOWN:
+	case USB_CHG_TYPE_NONE:
+	default:
+		return false;
+	}
+}
+
 static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 				       bool force)
 {
 	struct device *dev = info->dev;
 	int role, power_type;
+	unsigned int dr = DR_NONE;
+	bool pr = false;
 	bool polarity = false;
 	bool dp = false;
 	bool mux = false;
@@ -206,9 +278,12 @@ static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 			dev_err(dev, "failed getting role err = %d\n", role);
 			return role;
 		}
+		dev_dbg(dev, "disconnected\n");
 	} else {
 		int pd_mux_state;
 
+		dr = (role & PD_CTRL_RESP_ROLE_DATA) ? DR_HOST : DR_DEVICE;
+		pr = (role & PD_CTRL_RESP_ROLE_POWER);
 		pd_mux_state = cros_ec_usb_get_pd_mux_state(info);
 		if (pd_mux_state < 0)
 			pd_mux_state = USB_PD_MUX_USB_ENABLED;
@@ -216,20 +291,62 @@ static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 		dp = pd_mux_state & USB_PD_MUX_DP_ENABLED;
 		mux = pd_mux_state & USB_PD_MUX_USB_ENABLED;
 		hpd = pd_mux_state & USB_PD_MUX_HPD_IRQ;
+
+		dev_dbg(dev,
+			"connected role 0x%x pwr type %d dr %d pr %d pol %d mux %d dp %d hpd %d\n",
+			role, power_type, dr, pr, polarity, mux, dp, hpd);
 	}
 
-	if (force || info->dp != dp || info->mux != mux ||
-		info->power_type != power_type) {
+	/*
+	 * When there is no USB host (e.g. USB PD charger),
+	 * we are not really a UFP for the AP.
+	 */
+	if (dr == DR_DEVICE &&
+	    cros_ec_usb_power_type_is_wall_wart(power_type, role))
+		dr = DR_NONE;
 
+	if (force || info->dr != dr || info->pr != pr || info->dp != dp ||
+	    info->mux != mux || info->power_type != power_type) {
+		bool host_connected = false, device_connected = false;
+
+		dev_dbg(dev, "Type/Role switch! type = %s role = %s\n",
+			cros_ec_usb_power_type_string(power_type),
+			cros_ec_usb_role_string(dr));
+		info->dr = dr;
+		info->pr = pr;
 		info->dp = dp;
 		info->mux = mux;
 		info->power_type = power_type;
 
-		extcon_set_state(info->edev, EXTCON_DISP_DP, dp);
+		if (dr == DR_DEVICE)
+			device_connected = true;
+		else if (dr == DR_HOST)
+			host_connected = true;
 
+		extcon_set_state(info->edev, EXTCON_USB, device_connected);
+		extcon_set_state(info->edev, EXTCON_USB_HOST, host_connected);
+		extcon_set_state(info->edev, EXTCON_DISP_DP, dp);
+		extcon_set_property(info->edev, EXTCON_USB,
+				    EXTCON_PROP_USB_VBUS,
+				    (union extcon_property_value)(int)pr);
+		extcon_set_property(info->edev, EXTCON_USB_HOST,
+				    EXTCON_PROP_USB_VBUS,
+				    (union extcon_property_value)(int)pr);
+		extcon_set_property(info->edev, EXTCON_USB,
+				    EXTCON_PROP_USB_TYPEC_POLARITY,
+				    (union extcon_property_value)(int)polarity);
+		extcon_set_property(info->edev, EXTCON_USB_HOST,
+				    EXTCON_PROP_USB_TYPEC_POLARITY,
+				    (union extcon_property_value)(int)polarity);
 		extcon_set_property(info->edev, EXTCON_DISP_DP,
 				    EXTCON_PROP_USB_TYPEC_POLARITY,
 				    (union extcon_property_value)(int)polarity);
+		extcon_set_property(info->edev, EXTCON_USB,
+				    EXTCON_PROP_USB_SS,
+				    (union extcon_property_value)(int)mux);
+		extcon_set_property(info->edev, EXTCON_USB_HOST,
+				    EXTCON_PROP_USB_SS,
+				    (union extcon_property_value)(int)mux);
 		extcon_set_property(info->edev, EXTCON_DISP_DP,
 				    EXTCON_PROP_USB_SS,
 				    (union extcon_property_value)(int)mux);
@@ -237,6 +354,8 @@ static int extcon_cros_ec_detect_cable(struct cros_ec_extcon_info *info,
 				    EXTCON_PROP_DISP_HPD,
 				    (union extcon_property_value)(int)hpd);
 
+		extcon_sync(info->edev, EXTCON_USB);
+		extcon_sync(info->edev, EXTCON_USB_HOST);
 		extcon_sync(info->edev, EXTCON_DISP_DP);
 
 	} else if (hpd) {
@@ -322,13 +441,28 @@ static int extcon_cros_ec_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	extcon_set_property_capability(info->edev, EXTCON_USB,
+				       EXTCON_PROP_USB_VBUS);
+	extcon_set_property_capability(info->edev, EXTCON_USB_HOST,
+				       EXTCON_PROP_USB_VBUS);
+	extcon_set_property_capability(info->edev, EXTCON_USB,
+				       EXTCON_PROP_USB_TYPEC_POLARITY);
+	extcon_set_property_capability(info->edev, EXTCON_USB_HOST,
+				       EXTCON_PROP_USB_TYPEC_POLARITY);
 	extcon_set_property_capability(info->edev, EXTCON_DISP_DP,
 				       EXTCON_PROP_USB_TYPEC_POLARITY);
+	extcon_set_property_capability(info->edev, EXTCON_USB,
+				       EXTCON_PROP_USB_SS);
+	extcon_set_property_capability(info->edev, EXTCON_USB_HOST,
+				       EXTCON_PROP_USB_SS);
 	extcon_set_property_capability(info->edev, EXTCON_DISP_DP,
 				       EXTCON_PROP_USB_SS);
 	extcon_set_property_capability(info->edev, EXTCON_DISP_DP,
 				       EXTCON_PROP_DISP_HPD);
 
+	info->dr = DR_NONE;
+	info->pr = false;
+
 	platform_set_drvdata(pdev, info);
 
 	/* Get PD events from the EC */

drivers/leds/leds-pm8058.c

@@ -106,7 +106,7 @@ static int pm8058_led_probe(struct platform_device *pdev)
 	if (!led)
 		return -ENOMEM;
 
-	led->ledtype = (u32)of_device_get_match_data(&pdev->dev);
+	led->ledtype = (u32)(unsigned long)of_device_get_match_data(&pdev->dev);
 
 	map = dev_get_regmap(pdev->dev.parent, NULL);
 	if (!map) {

drivers/memstick/host/Kconfig

@@ -45,7 +45,7 @@ config MEMSTICK_R592
 
 config MEMSTICK_REALTEK_PCI
 	tristate "Realtek PCI-E Memstick Card Interface Driver"
-	depends on MFD_RTSX_PCI
+	depends on MISC_RTSX_PCI
 	help
 	  Say Y here to include driver code to support Memstick card interface
 	  of Realtek PCI-E card reader
@@ -55,7 +55,7 @@ config MEMSTICK_REALTEK_PCI
 
 config MEMSTICK_REALTEK_USB
 	tristate "Realtek USB Memstick Card Interface Driver"
-	depends on MFD_RTSX_USB
+	depends on MISC_RTSX_USB
 	help
 	  Say Y here to include driver code to support Memstick card interface
 	  of Realtek RTS5129/39 series USB card reader

drivers/memstick/host/rtsx_pci_ms.c

@@ -24,7 +24,7 @@
 #include <linux/delay.h>
 #include <linux/platform_device.h>
 #include <linux/memstick.h>
-#include <linux/mfd/rtsx_pci.h>
+#include <linux/rtsx_pci.h>
 #include <asm/unaligned.h>
 
 struct realtek_pci_ms {

drivers/memstick/host/rtsx_usb_ms.c

@@ -25,7 +25,7 @@
 #include <linux/workqueue.h>
 #include <linux/memstick.h>
 #include <linux/kthread.h>
-#include <linux/mfd/rtsx_usb.h>
+#include <linux/rtsx_usb.h>
 #include <linux/pm_runtime.h>
 #include <linux/mutex.h>
 #include <linux/sched.h>

drivers/mfd/Kconfig

@@ -222,6 +222,16 @@ config MFD_CROS_EC_SPI
 	  response time cannot be guaranteed, we support ignoring
 	  'pre-amble' bytes before the response actually starts.
 
+config MFD_CROS_EC_CHARDEV
+        tristate "Chrome OS Embedded Controller userspace device interface"
+        depends on MFD_CROS_EC
+        select CROS_EC_CTL
+        ---help---
+          This driver adds support to talk with the ChromeOS EC from userspace.
+
+          If you have a supported Chromebook, choose Y or M here.
+          The module will be called cros_ec_dev.
+
 config MFD_ASIC3
 	bool "Compaq ASIC3"
 	depends on GPIOLIB && ARM
@@ -929,17 +939,6 @@ config MFD_RDC321X
 	  southbridge which provides access to GPIOs and Watchdog using the
 	  southbridge PCI device configuration space.
 
-config MFD_RTSX_PCI
-	tristate "Realtek PCI-E card reader"
-	depends on PCI
-	select MFD_CORE
-	help
-	  This supports for Realtek PCI-Express card reader including rts5209,
-	  rts5227, rts522A, rts5229, rts5249, rts524A, rts525A, rtl8411, etc.
-	  Realtek card reader supports access to many types of memory cards,
-	  such as Memory Stick, Memory Stick Pro, Secure Digital and
-	  MultiMediaCard.
-
 config MFD_RT5033
 	tristate "Richtek RT5033 Power Management IC"
 	depends on I2C
@@ -953,16 +952,6 @@ config MFD_RT5033
 	  sub-devices like charger, fuel gauge, flash LED, current source,
 	  LDO and Buck.
 
-config MFD_RTSX_USB
-	tristate "Realtek USB card reader"
-	depends on USB
-	select MFD_CORE
-	help
-	  Select this option to get support for Realtek USB 2.0 card readers
-	  including RTS5129, RTS5139, RTS5179 and RTS5170.
-	  Realtek card reader supports access to many types of memory cards,
-	  such as Memory Stick Pro, Secure Digital and MultiMediaCard.
-
 config MFD_RC5T583
 	bool "Ricoh RC5T583 Power Management system device"
 	depends on I2C=y
@@ -1859,5 +1848,13 @@ config MFD_VEXPRESS_SYSREG
 	  System Registers are the platform configuration block
 	  on the ARM Ltd. Versatile Express board.
 
+config RAVE_SP_CORE
+	tristate "RAVE SP MCU core driver"
+	depends on SERIAL_DEV_BUS
+	select CRC_CCITT
+	help
+	  Select this to get support for the Supervisory Processor
+	  device found on several devices in RAVE line of hardware.
+
 endmenu
 endif

drivers/mfd/Makefile

@@ -17,12 +17,9 @@ cros_ec_core-$(CONFIG_ACPI)	+= cros_ec_acpi_gpe.o
 obj-$(CONFIG_MFD_CROS_EC)	+= cros_ec_core.o
 obj-$(CONFIG_MFD_CROS_EC_I2C)	+= cros_ec_i2c.o
 obj-$(CONFIG_MFD_CROS_EC_SPI)	+= cros_ec_spi.o
+obj-$(CONFIG_MFD_CROS_EC_CHARDEV) += cros_ec_dev.o
 obj-$(CONFIG_MFD_EXYNOS_LPASS)	+= exynos-lpass.o
 
-rtsx_pci-objs			:= rtsx_pcr.o rts5209.o rts5229.o rtl8411.o rts5227.o rts5249.o
-obj-$(CONFIG_MFD_RTSX_PCI)	+= rtsx_pci.o
-obj-$(CONFIG_MFD_RTSX_USB)	+= rtsx_usb.o
-
 obj-$(CONFIG_HTC_PASIC3)	+= htc-pasic3.o
 obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
 
@@ -230,3 +227,5 @@ obj-$(CONFIG_MFD_STM32_LPTIMER)	+= stm32-lptimer.o
 obj-$(CONFIG_MFD_STM32_TIMERS) 	+= stm32-timers.o
 obj-$(CONFIG_MFD_MXS_LRADC)     += mxs-lradc.o
 obj-$(CONFIG_MFD_SC27XX_PMIC)	+= sprd-sc27xx-spi.o
+obj-$(CONFIG_RAVE_SP_CORE)	+= rave-sp.o
+

drivers/mfd/cros_ec.c

@@ -40,13 +40,13 @@ static struct cros_ec_platform pd_p = {
 };
 
 static const struct mfd_cell ec_cell = {
-	.name = "cros-ec-ctl",
+	.name = "cros-ec-dev",
 	.platform_data = &ec_p,
 	.pdata_size = sizeof(ec_p),
 };
 
 static const struct mfd_cell ec_pd_cell = {
-	.name = "cros-ec-ctl",
+	.name = "cros-ec-dev",
 	.platform_data = &pd_p,
 	.pdata_size = sizeof(pd_p),
 };

drivers/mfd/cros_ec_dev.c

@@ -25,9 +25,10 @@
 #include <linux/slab.h>
 #include <linux/uaccess.h>
 
-#include "cros_ec_debugfs.h"
 #include "cros_ec_dev.h"
 
+#define DRV_NAME "cros-ec-dev"
+
 /* Device variables */
 #define CROS_MAX_DEV 128
 static int ec_major;
@@ -461,7 +462,7 @@ static int ec_device_remove(struct platform_device *pdev)
 }
 
 static const struct platform_device_id cros_ec_id[] = {
-	{ "cros-ec-ctl", 0 },
+	{ DRV_NAME, 0 },
 	{ /* sentinel */ },
 };
 MODULE_DEVICE_TABLE(platform, cros_ec_id);
@@ -493,7 +494,7 @@ static const struct dev_pm_ops cros_ec_dev_pm_ops = {
 
 static struct platform_driver cros_ec_dev_driver = {
 	.driver = {
-		.name = "cros-ec-ctl",
+		.name = DRV_NAME,
 		.pm = &cros_ec_dev_pm_ops,
 	},
 	.probe = ec_device_probe,
@@ -544,6 +545,7 @@ static void __exit cros_ec_dev_exit(void)
 module_init(cros_ec_dev_init);
 module_exit(cros_ec_dev_exit);
 
+MODULE_ALIAS("platform:" DRV_NAME);
 MODULE_AUTHOR("Bill Richardson <wfrichar@chromium.org>");
 MODULE_DESCRIPTION("Userspace interface to the Chrome OS Embedded Controller");
 MODULE_VERSION("1.0");

drivers/misc/Kconfig

@@ -496,6 +496,10 @@ config PCI_ENDPOINT_TEST
            Enable this configuration option to enable the host side test driver
            for PCI Endpoint.
 
+config MISC_RTSX
+	tristate
+	default MISC_RTSX_PCI || MISC_RTSX_USB
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"
@@ -508,4 +512,5 @@ source "drivers/misc/mic/Kconfig"
 source "drivers/misc/genwqe/Kconfig"
 source "drivers/misc/echo/Kconfig"
 source "drivers/misc/cxl/Kconfig"
+source "drivers/misc/cardreader/Kconfig"
 endmenu

drivers/misc/Makefile

@@ -55,6 +55,7 @@ obj-$(CONFIG_CXL_BASE)		+= cxl/
 obj-$(CONFIG_ASPEED_LPC_CTRL)	+= aspeed-lpc-ctrl.o
 obj-$(CONFIG_ASPEED_LPC_SNOOP)	+= aspeed-lpc-snoop.o
 obj-$(CONFIG_PCI_ENDPOINT_TEST)	+= pci_endpoint_test.o
+obj-$(CONFIG_MISC_RTSX)	+= cardreader/
 
 lkdtm-$(CONFIG_LKDTM)		+= lkdtm_core.o
 lkdtm-$(CONFIG_LKDTM)		+= lkdtm_bugs.o

drivers/misc/cardreader/Kconfig

@@ -0,0 +1,20 @@
+config MISC_RTSX_PCI
+	tristate "Realtek PCI-E card reader"
+	depends on PCI
+	select MFD_CORE
+	help
+	  This supports for Realtek PCI-Express card reader including rts5209,
+	  rts5227, rts522A, rts5229, rts5249, rts524A, rts525A, rtl8411, rts5260.
+	  Realtek card readers support access to many types of memory cards,
+	  such as Memory Stick, Memory Stick Pro, Secure Digital and
+	  MultiMediaCard.
+
+config MISC_RTSX_USB
+	tristate "Realtek USB card reader"
+	depends on USB
+	select MFD_CORE
+	help
+	  Select this option to get support for Realtek USB 2.0 card readers
+	  including RTS5129, RTS5139, RTS5179 and RTS5170.
+	  Realtek card reader supports access to many types of memory cards,
+	  such as Memory Stick Pro, Secure Digital and MultiMediaCard.

drivers/misc/cardreader/Makefile

@@ -0,0 +1,4 @@
+rtsx_pci-objs := rtsx_pcr.o rts5209.o rts5229.o rtl8411.o rts5227.o rts5249.o rts5260.o
+
+obj-$(CONFIG_MISC_RTSX_PCI)	+= rtsx_pci.o
+obj-$(CONFIG_MISC_RTSX_USB)	+= rtsx_usb.o

drivers/misc/cardreader/rtl8411.c

@@ -23,7 +23,7 @@
 #include <linux/module.h>
 #include <linux/bitops.h>
 #include <linux/delay.h>
-#include <linux/mfd/rtsx_pci.h>
+#include <linux/rtsx_pci.h>
 
 #include "rtsx_pcr.h"
 

drivers/misc/cardreader/rts5209.c

@@ -21,7 +21,7 @@
 
 #include <linux/module.h>
 #include <linux/delay.h>
-#include <linux/mfd/rtsx_pci.h>
+#include <linux/rtsx_pci.h>
 
 #include "rtsx_pcr.h"