Merge branch 'for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into i2c/for-4.15

Refactor i2c-gpio and its users to use gpiod. Done by GPIO maintainer
LinusW.

Documentation/devicetree/bindings/i2c/i2c-gpio.txt

@@ -2,25 +2,39 @@ Device-Tree bindings for i2c gpio driver
 
 Required properties:
 	- compatible = "i2c-gpio";
-	- gpios: sda and scl gpio
-
+	- sda-gpios: gpio used for the sda signal, this should be flagged as
+	  active high using open drain with (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)
+	  from <dt-bindings/gpio/gpio.h> since the signal is by definition
+	  open drain.
+	- scl-gpios: gpio used for the scl signal, this should be flagged as
+	  active high using open drain with (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)
+	  from <dt-bindings/gpio/gpio.h> since the signal is by definition
+	  open drain.
 
 Optional properties:
-	- i2c-gpio,sda-open-drain: sda as open drain
-	- i2c-gpio,scl-open-drain: scl as open drain
 	- i2c-gpio,scl-output-only: scl as output only
 	- i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
 	- i2c-gpio,timeout-ms: timeout to get data
 
+Deprecated properties, do not use in new device tree sources:
+	- gpios: sda and scl gpio, alternative for {sda,scl}-gpios
+	- i2c-gpio,sda-open-drain: this means that something outside of our
+	  control has put the GPIO line used for SDA into open drain mode, and
+	  that something is not the GPIO chip. It is essentially an
+	  inconsistency flag.
+	- i2c-gpio,scl-open-drain: this means that something outside of our
+	  control has put the GPIO line used for SCL into open drain mode, and
+	  that something is not the GPIO chip. It is essentially an
+	  inconsistency flag.
+
 Example nodes:
 
+#include <dt-bindings/gpio/gpio.h>
+
 i2c@0 {
 	compatible = "i2c-gpio";
-	gpios = <&pioA 23 0 /* sda */
-		 &pioA 24 0 /* scl */
-		>;
-	i2c-gpio,sda-open-drain;
-	i2c-gpio,scl-open-drain;
+	sda-gpios = <&pioA 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&pioA 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 	i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	#address-cells = <1>;
 	#size-cells = <0>;

arch/arm/mach-ep93xx/core.c

@@ -31,7 +31,7 @@
 #include <linux/amba/serial.h>
 #include <linux/mtd/physmap.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/spi/spi.h>
 #include <linux/export.h>
 #include <linux/irqchip/arm-vic.h>
@@ -320,42 +320,47 @@ void __init ep93xx_register_eth(struct ep93xx_eth_data *data, int copy_addr)
 /*************************************************************************
  * EP93xx i2c peripheral handling
  *************************************************************************/
-static struct i2c_gpio_platform_data ep93xx_i2c_data;
+
+/* All EP93xx devices use the same two GPIO pins for I2C bit-banging */
+static struct gpiod_lookup_table ep93xx_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		/* Use local offsets on gpiochip/port "G" */
+		GPIO_LOOKUP_IDX("G", 1, NULL, 0,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("G", 0, NULL, 1,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
 
 static struct platform_device ep93xx_i2c_device = {
 	.name		= "i2c-gpio",
 	.id		= 0,
 	.dev		= {
-		.platform_data	= &ep93xx_i2c_data,
+		.platform_data	= NULL,
 	},
 };
 
 /**
  * ep93xx_register_i2c - Register the i2c platform device.
- * @data:	platform specific i2c-gpio configuration (__initdata)
  * @devices:	platform specific i2c bus device information (__initdata)
  * @num:	the number of devices on the i2c bus
  */
-void __init ep93xx_register_i2c(struct i2c_gpio_platform_data *data,
-				struct i2c_board_info *devices, int num)
+void __init ep93xx_register_i2c(struct i2c_board_info *devices, int num)
 {
 	/*
-	 * Set the EEPROM interface pin drive type control.
-	 * Defines the driver type for the EECLK and EEDAT pins as either
-	 * open drain, which will require an external pull-up, or a normal
-	 * CMOS driver.
+	 * FIXME: this just sets the two pins as non-opendrain, as no
+	 * platforms tries to do that anyway. Flag the applicable lines
+	 * as open drain in the GPIO_LOOKUP above and the driver or
+	 * gpiolib will handle open drain/open drain emulation as need
+	 * be. Right now i2c-gpio emulates open drain which is not
+	 * optimal.
 	 */
-	if (data->sda_is_open_drain && data->sda_pin != EP93XX_GPIO_LINE_EEDAT)
-		pr_warning("sda != EEDAT, open drain has no effect\n");
-	if (data->scl_is_open_drain && data->scl_pin != EP93XX_GPIO_LINE_EECLK)
-		pr_warning("scl != EECLK, open drain has no effect\n");
-
-	__raw_writel((data->sda_is_open_drain << 1) |
-		     (data->scl_is_open_drain << 0),
+	__raw_writel((0 << 1) | (0 << 0),
 		     EP93XX_GPIO_EEDRIVE);
 
-	ep93xx_i2c_data = *data;
 	i2c_register_board_info(0, devices, num);
+	gpiod_add_lookup_table(&ep93xx_i2c_gpiod_table);
 	platform_device_register(&ep93xx_i2c_device);
 }
 

arch/arm/mach-ep93xx/edb93xx.c

@@ -28,7 +28,6 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
 #include <linux/spi/spi.h>
 
 #include <sound/cs4271.h>
@@ -61,14 +60,6 @@ static struct ep93xx_eth_data __initdata edb93xx_eth_data = {
 /*************************************************************************
  * EDB93xx i2c peripheral handling
  *************************************************************************/
-static struct i2c_gpio_platform_data __initdata edb93xx_i2c_gpio_data = {
-	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
-	.sda_is_open_drain	= 0,
-	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
-	.scl_is_open_drain	= 0,
-	.udelay			= 0,	/* default to 100 kHz */
-	.timeout		= 0,	/* default to 100 ms */
-};
 
 static struct i2c_board_info __initdata edb93xxa_i2c_board_info[] = {
 	{
@@ -86,13 +77,11 @@ static void __init edb93xx_register_i2c(void)
 {
 	if (machine_is_edb9302a() || machine_is_edb9307a() ||
 	    machine_is_edb9315a()) {
-		ep93xx_register_i2c(&edb93xx_i2c_gpio_data,
-				    edb93xxa_i2c_board_info,
+		ep93xx_register_i2c(edb93xxa_i2c_board_info,
 				    ARRAY_SIZE(edb93xxa_i2c_board_info));
 	} else if (machine_is_edb9302() || machine_is_edb9307()
 		|| machine_is_edb9312() || machine_is_edb9315()) {
-		ep93xx_register_i2c(&edb93xx_i2c_gpio_data,
-				    edb93xx_i2c_board_info,
+		ep93xx_register_i2c(edb93xx_i2c_board_info,
 				    ARRAY_SIZE(edb93xx_i2c_board_info));
 	}
 }

arch/arm/mach-ep93xx/include/mach/platform.h

@@ -7,7 +7,6 @@
 #include <linux/reboot.h>
 
 struct device;
-struct i2c_gpio_platform_data;
 struct i2c_board_info;
 struct spi_board_info;
 struct platform_device;
@@ -36,8 +35,7 @@ void ep93xx_register_flash(unsigned int width,
 			   resource_size_t start, resource_size_t size);
 
 void ep93xx_register_eth(struct ep93xx_eth_data *data, int copy_addr);
-void ep93xx_register_i2c(struct i2c_gpio_platform_data *data,
-			 struct i2c_board_info *devices, int num);
+void ep93xx_register_i2c(struct i2c_board_info *devices, int num);
 void ep93xx_register_spi(struct ep93xx_spi_info *info,
 			 struct spi_board_info *devices, int num);
 void ep93xx_register_fb(struct ep93xxfb_mach_info *data);

arch/arm/mach-ep93xx/simone.c

@@ -19,7 +19,6 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
 #include <linux/mmc/host.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/mmc_spi.h>
@@ -129,15 +128,6 @@ static struct ep93xx_spi_info simone_spi_info __initdata = {
 	.use_dma = 1,
 };
 
-static struct i2c_gpio_platform_data __initdata simone_i2c_gpio_data = {
-	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
-	.sda_is_open_drain	= 0,
-	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
-	.scl_is_open_drain	= 0,
-	.udelay			= 0,
-	.timeout		= 0,
-};
-
 static struct i2c_board_info __initdata simone_i2c_board_info[] = {
 	{
 		I2C_BOARD_INFO("ds1337", 0x68),
@@ -161,7 +151,7 @@ static void __init simone_init_machine(void)
 	ep93xx_register_flash(2, EP93XX_CS6_PHYS_BASE, SZ_8M);
 	ep93xx_register_eth(&simone_eth_data, 1);
 	ep93xx_register_fb(&simone_fb_info);
-	ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info,
+	ep93xx_register_i2c(simone_i2c_board_info,
 			    ARRAY_SIZE(simone_i2c_board_info));
 	ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
 			    ARRAY_SIZE(simone_spi_devices));

arch/arm/mach-ep93xx/snappercl15.c

@@ -21,7 +21,6 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
 #include <linux/fb.h>
 
 #include <linux/mtd/partitions.h>
@@ -127,15 +126,6 @@ static struct ep93xx_eth_data __initdata snappercl15_eth_data = {
 	.phy_id			= 1,
 };
 
-static struct i2c_gpio_platform_data __initdata snappercl15_i2c_gpio_data = {
-	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
-	.sda_is_open_drain	= 0,
-	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
-	.scl_is_open_drain	= 0,
-	.udelay			= 0,
-	.timeout		= 0,
-};
-
 static struct i2c_board_info __initdata snappercl15_i2c_data[] = {
 	{
 		/* Audio codec */
@@ -161,7 +151,7 @@ static void __init snappercl15_init_machine(void)
 {
 	ep93xx_init_devices();
 	ep93xx_register_eth(&snappercl15_eth_data, 1);
-	ep93xx_register_i2c(&snappercl15_i2c_gpio_data, snappercl15_i2c_data,
+	ep93xx_register_i2c(snappercl15_i2c_data,
 			    ARRAY_SIZE(snappercl15_i2c_data));
 	ep93xx_register_fb(&snappercl15_fb_info);
 	snappercl15_register_audio();

arch/arm/mach-ep93xx/vision_ep9307.c

@@ -22,7 +22,6 @@
 #include <linux/io.h>
 #include <linux/mtd/partitions.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
 #include <linux/platform_data/pca953x.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
@@ -144,10 +143,6 @@ static struct pca953x_platform_data pca953x_77_gpio_data = {
 /*************************************************************************
  * I2C Bus
  *************************************************************************/
-static struct i2c_gpio_platform_data vision_i2c_gpio_data __initdata = {
-	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
-	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
-};
 
 static struct i2c_board_info vision_i2c_info[] __initdata = {
 	{
@@ -289,7 +284,7 @@ static void __init vision_init_machine(void)
 
 	vision_i2c_info[1].irq = gpio_to_irq(EP93XX_GPIO_LINE_F(7));
 
-	ep93xx_register_i2c(&vision_i2c_gpio_data, vision_i2c_info,
+	ep93xx_register_i2c(vision_i2c_info,
 				ARRAY_SIZE(vision_i2c_info));
 	ep93xx_register_spi(&vision_spi_master, vision_spi_board_info,
 				ARRAY_SIZE(vision_spi_board_info));

arch/arm/mach-ixp4xx/avila-setup.c

@@ -17,7 +17,7 @@
 #include <linux/serial.h>
 #include <linux/tty.h>
 #include <linux/serial_8250.h>
-#include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 #include <asm/types.h>
 #include <asm/setup.h>
 #include <asm/memory.h>
@@ -49,16 +49,21 @@ static struct platform_device avila_flash = {
 	.resource	= &avila_flash_resource,
 };
 
-static struct i2c_gpio_platform_data avila_i2c_gpio_data = {
-	.sda_pin	= AVILA_SDA_PIN,
-	.scl_pin	= AVILA_SCL_PIN,
+static struct gpiod_lookup_table avila_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", AVILA_SDA_PIN,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", AVILA_SCL_PIN,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
 };
 
 static struct platform_device avila_i2c_gpio = {
 	.name		= "i2c-gpio",
 	.id		= 0,
 	.dev	 = {
-		.platform_data	= &avila_i2c_gpio_data,
+		.platform_data	= NULL,
 	},
 };
 
@@ -147,6 +152,8 @@ static void __init avila_init(void)
 	avila_flash_resource.end =
 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 
+	gpiod_add_lookup_table(&avila_i2c_gpiod_table);
+
 	platform_add_devices(avila_devices, ARRAY_SIZE(avila_devices));
 
 	avila_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1);

arch/arm/mach-ixp4xx/dsmg600-setup.c

@@ -25,7 +25,7 @@
 #include <linux/leds.h>
 #include <linux/reboot.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 
 #include <mach/hardware.h>
 
@@ -68,16 +68,21 @@ static struct platform_device dsmg600_flash = {
 	.resource		= &dsmg600_flash_resource,
 };
 
-static struct i2c_gpio_platform_data dsmg600_i2c_gpio_data = {
-	.sda_pin		= DSMG600_SDA_PIN,
-	.scl_pin		= DSMG600_SCL_PIN,
+static struct gpiod_lookup_table dsmg600_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", DSMG600_SDA_PIN,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", DSMG600_SCL_PIN,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
 };
 
 static struct platform_device dsmg600_i2c_gpio = {
 	.name			= "i2c-gpio",
 	.id			= 0,
 	.dev	 = {
-		.platform_data	= &dsmg600_i2c_gpio_data,
+		.platform_data	= NULL,
 	},
 };
 
@@ -269,6 +274,7 @@ static void __init dsmg600_init(void)
 	dsmg600_flash_resource.end =
 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 
+	gpiod_add_lookup_table(&dsmg600_i2c_gpiod_table);
 	i2c_register_board_info(0, dsmg600_i2c_board_info,
 				ARRAY_SIZE(dsmg600_i2c_board_info));
 

arch/arm/mach-ixp4xx/fsg-setup.c

@@ -22,7 +22,7 @@
 #include <linux/leds.h>
 #include <linux/reboot.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/io.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -54,16 +54,21 @@ static struct platform_device fsg_flash = {
 	.resource		= &fsg_flash_resource,
 };
 
-static struct i2c_gpio_platform_data fsg_i2c_gpio_data = {
-	.sda_pin		= FSG_SDA_PIN,
-	.scl_pin		= FSG_SCL_PIN,
+static struct gpiod_lookup_table fsg_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", FSG_SDA_PIN,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", FSG_SCL_PIN,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
 };
 
 static struct platform_device fsg_i2c_gpio = {
 	.name			= "i2c-gpio",
 	.id			= 0,
 	.dev = {
-		.platform_data	= &fsg_i2c_gpio_data,
+		.platform_data	= NULL,
 	},
 };
 
@@ -196,6 +201,7 @@ static void __init fsg_init(void)
 	/* Configure CS2 for operation, 8bit and writable */
 	*IXP4XX_EXP_CS2 = 0xbfff0002;
 
+	gpiod_add_lookup_table(&fsg_i2c_gpiod_table);
 	i2c_register_board_info(0, fsg_i2c_board_info,
 				ARRAY_SIZE(fsg_i2c_board_info));
 

arch/arm/mach-ixp4xx/goramo_mlr.c

@@ -6,7 +6,6 @@
 #include <linux/delay.h>
 #include <linux/gpio.h>
 #include <linux/hdlc.h>
-#include <linux/i2c-gpio.h>
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/kernel.h>
@@ -78,6 +77,12 @@
 static u32 hw_bits = 0xFFFFFFFD;    /* assume all hardware present */;
 static u8 control_value;
 
+/*
+ * FIXME: this is reimplementing I2C bit-bangining. Move this
+ * over to using driver/i2c/busses/i2c-gpio.c like all other boards
+ * and register proper I2C device(s) on the bus for this. (See
+ * other IXP4xx boards for examples.)
+ */
 static void set_scl(u8 value)
 {
 	gpio_set_value(GPIO_SCL, !!value);
@@ -216,20 +221,6 @@ static struct platform_device device_flash = {
 	.resource	= &flash_resource,
 };
 
-
-/* I^2C interface */
-static struct i2c_gpio_platform_data i2c_data = {
-	.sda_pin	= GPIO_SDA,
-	.scl_pin	= GPIO_SCL,
-};
-
-static struct platform_device device_i2c = {
-	.name		= "i2c-gpio",
-	.id		= 0,
-	.dev		= { .platform_data = &i2c_data },
-};
-
-
 /* IXP425 2 UART ports */
 static struct resource uart_resources[] = {
 	{
@@ -411,9 +402,6 @@ static void __init gmlr_init(void)
 	if (hw_bits & CFG_HW_HAS_HSS1)
 		device_tab[devices++] = &device_hss_tab[1]; /* max index 5 */
 
-	if (hw_bits & CFG_HW_HAS_EEPROM)
-		device_tab[devices++] = &device_i2c; /* max index 6 */
-
 	gpio_request(GPIO_SCL, "SCL/clock");
 	gpio_request(GPIO_SDA, "SDA/data");
 	gpio_request(GPIO_STR, "strobe");

arch/arm/mach-ixp4xx/ixdp425-setup.c

@@ -14,7 +14,7 @@
 #include <linux/serial.h>
 #include <linux/tty.h>
 #include <linux/serial_8250.h>
-#include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/io.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/rawnand.h>
@@ -122,16 +122,21 @@ static struct platform_device ixdp425_flash_nand = {
 };
 #endif	/* CONFIG_MTD_NAND_PLATFORM */
 
-static struct i2c_gpio_platform_data ixdp425_i2c_gpio_data = {
-	.sda_pin	= IXDP425_SDA_PIN,
-	.scl_pin	= IXDP425_SCL_PIN,
+static struct gpiod_lookup_table ixdp425_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", IXDP425_SDA_PIN,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", IXDP425_SCL_PIN,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
 };
 
 static struct platform_device ixdp425_i2c_gpio = {
 	.name		= "i2c-gpio",
 	.id		= 0,
 	.dev	 = {
-		.platform_data	= &ixdp425_i2c_gpio_data,
+		.platform_data	= NULL,
 	},
 };
 
@@ -245,6 +250,7 @@ static void __init ixdp425_init(void)
 		ixdp425_uart_data[1].flags = 0;
 	}
 
+	gpiod_add_lookup_table(&ixdp425_i2c_gpiod_table);
 	platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
 }
 

arch/arm/mach-ixp4xx/nas100d-setup.c

@@ -27,7 +27,7 @@
 #include <linux/leds.h>
 #include <linux/reboot.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/io.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -100,16 +100,21 @@ static struct platform_device nas100d_leds = {
 	.dev.platform_data	= &nas100d_led_data,
 };
 
-static struct i2c_gpio_platform_data nas100d_i2c_gpio_data = {
-	.sda_pin		= NAS100D_SDA_PIN,
-	.scl_pin		= NAS100D_SCL_PIN,
+static struct gpiod_lookup_table nas100d_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", NAS100D_SDA_PIN,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", NAS100D_SCL_PIN,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
 };
 
 static struct platform_device nas100d_i2c_gpio = {
 	.name			= "i2c-gpio",
 	.id			= 0,
 	.dev	 = {
-		.platform_data	= &nas100d_i2c_gpio_data,
+		.platform_data	= NULL,
 	},
 };
 
@@ -280,6 +285,7 @@ static void __init nas100d_init(void)
 	nas100d_flash_resource.end =
 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 
+	gpiod_add_lookup_table(&nas100d_i2c_gpiod_table);
 	i2c_register_board_info(0, nas100d_i2c_board_info,
 				ARRAY_SIZE(nas100d_i2c_board_info));
 

arch/arm/mach-ixp4xx/nslu2-setup.c

@@ -24,7 +24,7 @@
 #include <linux/leds.h>
 #include <linux/reboot.h>
 #include <linux/i2c.h>
-#include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/io.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -68,9 +68,14 @@ static struct platform_device nslu2_flash = {
 	.resource		= &nslu2_flash_resource,
 };
 
-static struct i2c_gpio_platform_data nslu2_i2c_gpio_data = {
-	.sda_pin		= NSLU2_SDA_PIN,
-	.scl_pin		= NSLU2_SCL_PIN,
+static struct gpiod_lookup_table nslu2_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", NSLU2_SDA_PIN,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", NSLU2_SCL_PIN,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
 };
 
 static struct i2c_board_info __initdata nslu2_i2c_board_info [] = {
@@ -115,7 +120,7 @@ static struct platform_device nslu2_i2c_gpio = {
 	.name			= "i2c-gpio",
 	.id			= 0,
 	.dev	 = {
-		.platform_data	= &nslu2_i2c_gpio_data,
+		.platform_data	= NULL,
 	},
 };
 
@@ -250,6 +255,7 @@ static void __init nslu2_init(void)
 	nslu2_flash_resource.end =
 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 
+	gpiod_add_lookup_table(&nslu2_i2c_gpiod_table);
 	i2c_register_board_info(0, nslu2_i2c_board_info,
 				ARRAY_SIZE(nslu2_i2c_board_info));
 

arch/arm/mach-ks8695/board-acs5k.c

@@ -16,7 +16,7 @@
 #include <linux/interrupt.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-
+#include <linux/gpio/machine.h>
 #include <linux/i2c.h>
 #include <linux/i2c-algo-bit.h>
 #include <linux/i2c-gpio.h>
@@ -38,9 +38,17 @@
 
 #include "generic.h"
 
+static struct gpiod_lookup_table acs5k_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("KS8695", 4, NULL, 0,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("KS8695", 5, NULL, 1,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
+
 static struct i2c_gpio_platform_data acs5k_i2c_device_platdata = {
-	.sda_pin	= 4,
-	.scl_pin	= 5,
 	.udelay		= 10,
 };
 
@@ -95,6 +103,7 @@ static struct i2c_board_info acs5k_i2c_devs[] __initdata = {
 static void acs5k_i2c_init(void)
 {
 	/* The gpio interface */
+	gpiod_add_lookup_table(&acs5k_i2c_gpiod_table);
 	platform_device_register(&acs5k_i2c_device);
 	/* I2C devices */
 	i2c_register_board_info(0, acs5k_i2c_devs,

arch/arm/mach-pxa/palmz72.c

@@ -31,6 +31,7 @@
 #include <linux/power_supply.h>
 #include <linux/usb/gpio_vbus.h>
 #include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 
 #include <asm/mach-types.h>
 #include <asm/suspend.h>
@@ -320,9 +321,17 @@ static struct soc_camera_link palmz72_iclink = {
 	.flags		= SOCAM_DATAWIDTH_8,
 };
 
+static struct gpiod_lookup_table palmz72_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("gpio-pxa", 118, NULL, 0,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("gpio-pxa", 117, NULL, 1,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
+
 static struct i2c_gpio_platform_data palmz72_i2c_bus_data = {
-	.sda_pin	= 118,
-	.scl_pin	= 117,
 	.udelay		= 10,
 	.timeout	= 100,
 };
@@ -369,6 +378,7 @@ static void __init palmz72_camera_init(void)
 {
 	palmz72_cam_gpio_init();
 	pxa_set_camera_info(&palmz72_pxacamera_platform_data);
+	gpiod_add_lookup_table(&palmz72_i2c_gpiod_table);
 	platform_device_register(&palmz72_i2c_bus_device);
 	platform_device_register(&palmz72_camera);
 }

arch/arm/mach-pxa/viper.c

@@ -36,6 +36,7 @@
 #include <linux/gpio.h>
 #include <linux/jiffies.h>
 #include <linux/i2c-gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/i2c/pxa-i2c.h>
 #include <linux/serial_8250.h>
 #include <linux/smc91x.h>
@@ -458,9 +459,17 @@ static struct platform_device smc91x_device = {
 };
 
 /* i2c */
+static struct gpiod_lookup_table viper_i2c_gpiod_table = {
+	.dev_id		= "i2c-gpio",
+	.table		= {
+		GPIO_LOOKUP_IDX("gpio-pxa", VIPER_RTC_I2C_SDA_GPIO,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("gpio-pxa", VIPER_RTC_I2C_SCL_GPIO,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
+
 static struct i2c_gpio_platform_data i2c_bus_data = {
-	.sda_pin = VIPER_RTC_I2C_SDA_GPIO,
-	.scl_pin = VIPER_RTC_I2C_SCL_GPIO,
 	.udelay  = 10,
 	.timeout = HZ,
 };
@@ -779,12 +788,20 @@ static int __init viper_tpm_setup(char *str)
 
 __setup("tpm=", viper_tpm_setup);
 
+struct gpiod_lookup_table viper_tpm_i2c_gpiod_table = {
+	.dev_id = "i2c-gpio",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", VIPER_TPM_I2C_SDA_GPIO,
+				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("gpio-pxa", VIPER_TPM_I2C_SCL_GPIO,
+				NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
+
 static void __init viper_tpm_init(void)
 {
 	struct platform_device *tpm_device;
 	struct i2c_gpio_platform_data i2c_tpm_data = {
-		.sda_pin = VIPER_TPM_I2C_SDA_GPIO,
-		.scl_pin = VIPER_TPM_I2C_SCL_GPIO,
 		.udelay  = 10,
 		.timeout = HZ,
 	};
@@ -794,6 +811,7 @@ static void __init viper_tpm_init(void)
 	if (!viper_tpm)
 		return;
 
+	gpiod_add_lookup_table(&viper_tpm_i2c_gpiod_table);
 	tpm_device = platform_device_alloc("i2c-gpio", 2);
 	if (tpm_device) {
 		if (!platform_device_add_data(tpm_device,
@@ -943,6 +961,7 @@ static void __init viper_init(void)
 		smc91x_device.num_resources--;
 
 	pxa_set_i2c_info(NULL);
+	gpiod_add_lookup_table(&viper_i2c_gpiod_table);
 	pwm_add_table(viper_pwm_lookup, ARRAY_SIZE(viper_pwm_lookup));
 	platform_add_devices(viper_devs, ARRAY_SIZE(viper_devs));
 

arch/arm/mach-sa1100/simpad.c

@@ -16,6 +16,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/io.h>
 #include <linux/gpio/driver.h>
+#include <linux/gpio/machine.h>
 
 #include <mach/hardware.h>
 #include <asm/setup.h>
@@ -323,9 +324,17 @@ static struct platform_device simpad_gpio_leds = {
 /*
  * i2c
  */
+static struct gpiod_lookup_table simpad_i2c_gpiod_table = {
+	.dev_id = "i2c-gpio",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio", GPIO_GPIO21, NULL, 0,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("gpio", GPIO_GPIO25, NULL, 1,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
+
 static struct i2c_gpio_platform_data simpad_i2c_data = {
-	.sda_pin = GPIO_GPIO21,
-	.scl_pin = GPIO_GPIO25,
 	.udelay = 10,
 	.timeout = HZ,
 };
@@ -380,6 +389,7 @@ static int __init simpad_init(void)
 			      ARRAY_SIZE(simpad_flash_resources));
 	sa11x0_register_mcp(&simpad_mcp_data);
 
+	gpiod_add_lookup_table(&simpad_i2c_gpiod_table);
 	ret = platform_add_devices(devices, ARRAY_SIZE(devices));
 	if(ret)
 		printk(KERN_WARNING "simpad: Unable to register mq200 framebuffer device");

arch/blackfin/mach-bf533/boards/blackstamp.c

@@ -22,6 +22,7 @@
 #include <linux/irq.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
+#include <linux/gpio/machine.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
@@ -362,11 +363,17 @@ static struct platform_device bfin_device_gpiokeys = {
 #if IS_ENABLED(CONFIG_I2C_GPIO)
 #include <linux/i2c-gpio.h>
 
+static struct gpiod_lookup_table bfin_i2c_gpiod_table = {
+	.dev_id = "i2c-gpio",
+	.table = {
+		GPIO_LOOKUP_IDX("BFIN-GPIO", GPIO_PF8, NULL, 0,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("BFIN-GPIO", GPIO_PF9, NULL, 1,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
+
 static struct i2c_gpio_platform_data i2c_gpio_data = {
-	.sda_pin		= GPIO_PF8,
-	.scl_pin		= GPIO_PF9,
-	.sda_is_open_drain	= 0,
-	.scl_is_open_drain	= 0,
 	.udelay			= 40,
 }; /* This hasn't actually been used these pins
     * are (currently) free pins on the expansion connector */
@@ -462,7 +469,9 @@ static int __init blackstamp_init(void)
 	int ret;
 
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
-
+#if IS_ENABLED(CONFIG_I2C_GPIO)
+	gpiod_add_lookup_table(&bfin_i2c_gpiod_table);
+#endif
 	i2c_register_board_info(0, bfin_i2c_board_info,
 				ARRAY_SIZE(bfin_i2c_board_info));
 

arch/blackfin/mach-bf533/boards/ezkit.c

@@ -19,6 +19,7 @@
 #endif
 #include <linux/irq.h>
 #include <linux/i2c.h>
+#include <linux/gpio/machine.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
@@ -390,11 +391,17 @@ static struct platform_device bfin_device_gpiokeys = {
 #if IS_ENABLED(CONFIG_I2C_GPIO)
 #include <linux/i2c-gpio.h>
 
+static struct gpiod_lookup_table bfin_i2c_gpiod_table = {
+	.dev_id = "i2c-gpio",
+	.table = {
+		GPIO_LOOKUP_IDX("BFIN-GPIO", GPIO_PF1, NULL, 0,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		GPIO_LOOKUP_IDX("BFIN-GPIO", GPIO_PF0, NULL, 1,
+				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+	},
+};
+
 static struct i2c_gpio_platform_data i2c_gpio_data = {
-	.sda_pin		= GPIO_PF1,
-	.scl_pin		= GPIO_PF0,
-	.sda_is_open_drain	= 0,
-	.scl_is_open_drain	= 0,
 	.udelay			= 40,
 };
 
@@ -516,6 +523,9 @@ static struct platform_device *ezkit_devices[] __initdata = {
 static int __init ezkit_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+#if IS_ENABLED(CONFIG_I2C_GPIO)
+	gpiod_add_lookup_table(&bfin_i2c_gpiod_table);
+#endif
 	platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	i2c_register_board_info(0, bfin_i2c_board_info,