- fix schematic link pointing to different board
- fix link to the board_defconfig file
- remove the "Debug Firmware" link that was not referenced anywhere
- add a link to the board user manual
- minor additions to the debug with J-Link section
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Remove explicit timeouts which are either the same as the
default one or smaller.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Let's increase the timeout for a few tests whose
timeout is less than 3x a typical execution time in CI.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This test keeps its own partial way of running tests.
Let's have it kill stuck processes in the same way as
the rest (sending another kill 5 seconds after, and printing
a message about what happened)
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add the invocation of an interrupt config function
(config->irq_config_func). Absence of this call results in the DMA
driver not being able to service interrupts raised by the DMA
peripheral.
This case was observed on the i.MX RT685's HiFi 4 DSP domain, where DMA
was not functional because of this.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
The LL_EXTENSION_SYMBOL macro is used to export symbols defined in
extensions to the base image. This patch reworks the macro to use
`static const struct llext_const_symbol`, since:
- the associated values are semantically not modifiable;
- this exported symbol table is parsed by llext like section iterables,
ignoring associated symbol information.
This is mostly a cosmetic change because, unlike the base image, these
symbols cannot be placed (and left) in ROM as they will most certainly
require runtime relocation. However, it makes this macro more consistent
with EXPORT_SYMBOL, which is the base image equivalent.
Also clarify some comments in the same header file.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Outgoing block-transfers now set the socket hint
to ONGOING as long as the BLOCK1/BLOCK2 header has
MORE flag set to true.
This means as only the last packet in the block-transfer
set the socket hint to LAST or ONE_RESPONSE.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
To give an idea of which tests are taking
too long either on CI or locally.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add SoC initialization to set the UART RDC permission in the early
phase, so that the it can be used by Zephyr on Cortex-A cores.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Create regulator on GPIO for microphone supply
Set pdm data and clk pins in pinctrl
Add xiao_ble_sense overlay for dmic sample support
Signed-off-by: Zak Portnoy <zakportnoy@gmail.com>
Let find_program in codechecker/sca.cmake search for both 'CodeChecker'
and 'codechecker'. Before this change, I wasn't able to run CodeChecker
because cmake couldn't find it. (Ubuntu 23.10, CodeChecker 6.21.0 installed
via snap)
Signed-off-by: Benedikt Streicher <streicher.b@posteo.de>
Once Wi-Fi is associated few parameters like listen interval and
power-save mode cannot be changed. The state for association is
"ASSOCIATED" and not completed. Even after state transitions to
COMPLETE, it can still go back to other states, e.g., PTK/GTK renewal.
Fix the state check.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
To minimize time the CPU spends when preparing for sleep, make sure
the pending transactions are finished before calling `wfi`.
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
If host is not reading RTT data (because there is no PC connection
or RTT reading application is not running on the host), thread will
stuck continuously trying to write to RTT. All threads with equal or
lower priority are blocked then. Adding detection of that case and
if host is not reading data for configurable period then data is
dropped until host accepts new data.
Similar solution is using in RTT logging backend.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Create the folder for the results if it does not exist.
Fixes these warnings in CI:
```
touch: cannot touch '/__w/zephyr/zephyr/./bsim_bt/
53_bsim_results.xml': No such file or directory
realpath: /__w/zephyr/zephyr/./bsim_bt/
53_bsim_results.xml: No such file or directory
```
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
