Add a very simple check that verifies that new error numbers are added
according to the errno.h file in newlib, in order to maintain
compatibility with it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds the missing `ARM_TRUSTZONE_M` config flag
from TrustZone-enabled cores on LPC55sxx board targets.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
The network layer previously decided to use the friend credentials if
there was an established friendship. During the friendship setup phase,
the friendship is not considered established until the LPN receives the
first friend poll. Before this happens, the LPN should send a friend
poll message, encrypted with the friendship credentials. This wrongly
gets encrypted with the master credentials.
Change the decision point to whether the LPN has selected a friend,
which happens after the friend offer, and before the friend poll. This
will remain set for the duration of the friendship.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
This adds BT_MESH_SETTINGS_VA_PENDING to GENERIC_PENDING_BITS
as it should be stored by CONFIG_BT_MESH_STORE_TIMEOUT.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This bug was introduced in PR #31176, where setting's flags were
moved out from bt_mesh.flags to pending_flags.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
When loaded via EFI, we obviously don't have a multiboot info pointer
available (we might have an EFI system table, but zefi doesn't pass
that through yet). Don't try to parse the "whatever garbage was in
%rbp" as a multiboot table.
The configuration is a little clumsy, as strictly our EFI kconfig just
says we're "building for" EFI but not that we'll boot that way. And
tests like arch/x86/info are trying to set CONFIG_MULTIBOOT=n
unconditionally, when it really should be something they detect from
devicetree or wherever.
Fixes#33545
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Kernel objects that contain embedded synchronization structures like
spinlocks can't be palced in the (cached/incoherent) stack memory on
coherence platforms like intel_adsp.
The normal fix in a test case is just to make the offending data
static, but that's painful here because SYS_BITARRAY_DEFINE declares
two objects (i.e. you can't put a "static" in front of it as with
similar macros) and it happens to be used in this case to define local
variables with collliding names, so I'd have to go in and rename
everything.
And there's little value anyway. Bitarrays are nearly-pure data
structures and extremely unlikely to show up platform-dependent
behavior.
Fixes#35242
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Two testcases of semaphore failed in ADSP due to the timeout value
we got back from the child thread is invalid. We put the variable in
the bss instead of in a stack, trying to avoid this.
Fixes#34687
Signed-off-by: Enjia Mai <enjiax.mai@intel.com>
The default behavior of the +KSRAT= command has
changed to not reboot the HL7800.
Adjust the command so the reboot takes place properly.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Simplified handling of runtime filtering that lead to removal
of LOG_CHECK_CTX_LVL_FILTER macro. Fixing multiply coverity issues
like CID 236013.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This was already implemented for firmware update packages.
For other opaque resources it failed to determine the target resource
id, which is now stored in the block_context.
Signed-off-by: Jan Buenker <jan.buenker@grandcentrix.net>
If the tests/net/socket/getaddrinfo is run in a board that has
Ethernet controller, then it is possible that it will interfere
the test if the Ethernet cable is connected. As the test only
needs loopback support to run, disable the Ethernet as it is
not needed by the test.
Fixes#34923
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
NPCX series ROM code changes the chip basic setting by firmware binary
header for loading the firmware from flash to RAM. Add the following to
improve the ec firmware header setting:
- Move the ECST which generates the firmware binary header to NPCX
common folder. All the following NPCX series chips can use this.
- Add ecst setting option in Kconfig.
Signed-off-by: Yuval Peress <peress@chromium.org>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Fix regression in PPIs use for nRF52805 SoC, which has
fewer of them. And the regression was introduced in
commit e603b9d59e ("Bluetooth: controller: Adjust PPI
used for nRF51x and nRF52x").
Fixes#35204.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixes compatibility with the Arduino bootloader reset mechanism when
using `west flash` on Darwin hosts.
stty is used to set the serial port in the bossac runner to 1200 baud on
Arduino ATSAMD21 bootloaders. The `-F` argument to stty is a GNU
coreutils addition, and thus it is missing from Darwin's BSD stty, so
change the flag to `-f` when we're not running on Linux.
On Darwin, set DEFAULT_BOSSAC_PORT to None and ask the user to select
one from a list of IOCalloutDevices reported by ioreg, modelled on the
get_board_snr from the nrfjprog runner. This is because serial port TTYs
are generated by the device driver, and therefore there is no safe
default.
Tested with an Arduino Nano 33 IoT board.
Signed-off-by: George White <me@galexite.uk>
add semaphores to ensure all services started before client query.
otherwise client query services may fail.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Z_ITERABLE_SECTION_ROM symbols were empty, meaning
that those symbols were not taking place in the linker script.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
