With this change for each setting we say which hierarachy it applies to briefly
in the first sentence of the description, plus in longer form in an extra
pargraph at the end, with a recommendation for the counterpart of the option in
the other hierarchy.
Also adds markup and the "=" suffix to all mentioned settings.
We currently generate log message about unit being started even when
unit was started already and job didn't do anything. This is because job
was requested explicitly and hence became anchor job of the transaction
thus we could not eliminate it. That is fine but, let's not pollute
journal with useless log messages.
$ systemctl start systemd-resolved
$ systemctl start systemd-resolved
$ systemctl start systemd-resolved
Current state:
$ journalctl -u systemd-resolved | grep Started
May 05 15:31:42 rawhide systemd[1]: Started Network Name Resolution.
May 05 15:31:59 rawhide systemd[1]: Started Network Name Resolution.
May 05 15:32:01 rawhide systemd[1]: Started Network Name Resolution.
After patch applied:
$ journalctl -u systemd-resolved | grep Started
May 05 16:42:12 rawhide systemd[1]: Started Network Name Resolution.
Fixes#1723
Private /dev will not be managed by udev or others, so we can make it
noexec and readonly after we have made all device nodes. As /dev/shm
needs to be writable, we can't use bind_remount_recursive().
While creating a VLAN the mac address should be copied from the parent interface, so that
the VLANs inherit the MAC address of the physical interface.
Before:
```
3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 00:26:c6:85:a3:c2 brd ff:ff:ff:ff:ff:ff
...
6: vlan1@wlp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 22:07:73:9d:43:59 brd ff:ff:ff:ff:ff:ff
7: vlan2@wlp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 46:30:76:33:35:d4 brd ff:ff:ff:ff:ff:ff
```
After:
```
3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 00:26:c6:85:a3:c2 brd ff:ff:ff:ff:ff:ff
...
11: vlan1@wlp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:26:c6:85:a3:c2 brd ff:ff:ff:ff:ff:ff
12: vlan2@wlp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:26:c6:85:a3:c2 brd ff:ff:ff:ff:ff:ff
```
v2 of #1573, with fixed commit message.
This patch implements support for the IFLA_BR_MCAST_SNOOPING attribute
it can change the multicast snooping value.
IGMP snooping monitors the Internet Group Management Protocol (IGMP)
traffic between hosts and multicast routers.
It is just an alias for route_free which requires that route is not null,
but it was only used in one place where it was checked that route is not
null anyway. Let's just call route_free instead.
This is now the recommended way to do monitoring by upstream D-Bus.
It's also allowed in the default policy, whereas eavesdrop is not
anymore, which effectively broke busctl on many systems.
unit_set_slice() fails with -EBUSY if the unit already has a slice associated
with it. This makes it impossible to override slice through dropin config or
over dbus. There's no reason to disallow slice changes as long as cgroups
aren't realized. Fix it.
Fixes#3240.
Signed-off-by: Tejun Heo <htejun@fb.com>
Reported-by: Davide Cavalca <dcavalca@fb.com>
