udpgso_bench_tx call setup_sockaddr() for dest address before
parsing all arguments, if we specify "-p ${dst_port}" after "-D ${dst_ip}",
then ${dst_port} will be ignored, and using default cfg_port 8000.
This will cause test case "multiple GRO socks" failed in udpgro.sh.
Setup sockaddr after parsing all arguments.
Fixes: 3a687bef14 ("selftests: udp gso benchmark")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/ff620d9f-5b52-06ab-5286-44b945453002@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov says:
====================
net: bridge: mcast: add and enforce query interval minimum
This set adds and enforces 1 second minimum value for bridge multicast
query and startup query intervals in order to avoid rearming the timers
too often which could lock and crash the host. I doubt anyone is using
such low values or anything lower than 1 second, so it seems like a good
minimum. In order to be compatible if the value is lower then it is
overwritten and a log message is emitted, since we can't return an error
at this point.
Eric, I looked for the syzbot reports in its dashboard but couldn't find
them so I've added you as the reporter.
I've prepared a global bridge igmp rate limiting patch but wasn't
sure if it's ok for -net. It adds a static limit of 32k packets per
second, I plan to send it for net-next with added drop counters for
each bridge so it can be easily debugged.
Original report can be seen at:
https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
====================
Link: https://lore.kernel.org/r/20211227172116.320768-1-nikolay@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if startup query interval is set too low in combination with
large number of startup queries and we have multiple bridges or even a
single bridge with multiple querier vlans configured we can crash the
machine. Add a 1 second minimum which must be enforced by overwriting the
value if set lower (i.e. without returning an error) to avoid breaking
user-space. If that happens a log message is emitted to let the admin know
that the startup interval has been set to the minimum. It doesn't make
sense to make the startup interval lower than the normal query interval
so use the same value of 1 second. The issue has been present since these
intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if query interval is set too low and we have multiple
bridges or even a single bridge with multiple querier vlans configured
we can crash the machine. Add a 1 second minimum which must be enforced
by overwriting the value if set lower (i.e. without returning an error) to
avoid breaking user-space. If that happens a log message is emitted to let
the administrator know that the interval has been set to the minimum.
The issue has been present since these intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit initialises the xskb's free_list_node when the xskb is
allocated. This prevents a potential false negative returned from a call
to list_empty for that node, such as the one introduced in commit
199d983bc0 ("xsk: Fix crash on double free in buffer pool")
In my environment this issue caused packets to not be received by
the xdpsock application if the traffic was running prior to application
launch. This happened when the first batch of packets failed the xskmap
lookup and XDP_PASS was returned from the bpf program. This action is
handled in the i40e zc driver (and others) by allocating an skbuff,
freeing the xdp_buff and adding the associated xskb to the
xsk_buff_pool's free_list if it hadn't been added already. Without this
fix, the xskb is not added to the free_list because the check to determine
if it was added already returns an invalid positive result. Later, this
caused allocation errors in the driver and the failure to receive packets.
Fixes: 199d983bc0 ("xsk: Fix crash on double free in buffer pool")
Fixes: 2b43470add ("xsk: Introduce AF_XDP buffer allocation API")
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/r/20211220155250.2746-1-ciara.loftus@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-28
This series contains updates to igc driver only.
Vinicius disables support for crosstimestamp on i225-V as lockups are being
observed.
James McLaughlin fixes Tx timestamping support on non-MSI-X platforms.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Fix TX timestamp support for non-MSI-X platforms
igc: Do not enable crosstimestamping for i225-V models
====================
Link: https://lore.kernel.org/r/20211228182421.340354-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dust Li says:
====================
net/smc: fix kernel panic caused by race of smc_sock
This patchset fixes the race between smc_release triggered by
close(2) and cdc_handle triggered by underlaying RDMA device.
The race is caused because the smc_connection may been released
before the pending tx CDC messages got its CQEs. In order to fix
this, I add a counter to track how many pending WRs we have posted
through the smc_connection, and only release the smc_connection
after there is no pending WRs on the connection.
The first patch prevents posting WR on a QP that is not in RTS
state. This patch is needed because if we post WR on a QP that
is not in RTS state, ib_post_send() may success but no CQE will
return, and that will confuse the counter tracking the pending
WRs.
The second patch add a counter to track how many WRs were posted
through the smc_connection, and don't reset the QP on link destroying
to prevent leak of the counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A crash occurs when smc_cdc_tx_handler() tries to access smc_sock
but smc_release() has already freed it.
[ 4570.695099] BUG: unable to handle page fault for address: 000000002eae9e88
[ 4570.696048] #PF: supervisor write access in kernel mode
[ 4570.696728] #PF: error_code(0x0002) - not-present page
[ 4570.697401] PGD 0 P4D 0
[ 4570.697716] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 4570.698228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.16.0-rc4+ #111
[ 4570.699013] Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/0
[ 4570.699933] RIP: 0010:_raw_spin_lock+0x1a/0x30
<...>
[ 4570.711446] Call Trace:
[ 4570.711746] <IRQ>
[ 4570.711992] smc_cdc_tx_handler+0x41/0xc0
[ 4570.712470] smc_wr_tx_tasklet_fn+0x213/0x560
[ 4570.712981] ? smc_cdc_tx_dismisser+0x10/0x10
[ 4570.713489] tasklet_action_common.isra.17+0x66/0x140
[ 4570.714083] __do_softirq+0x123/0x2f4
[ 4570.714521] irq_exit_rcu+0xc4/0xf0
[ 4570.714934] common_interrupt+0xba/0xe0
Though smc_cdc_tx_handler() checked the existence of smc connection,
smc_release() may have already dismissed and released the smc socket
before smc_cdc_tx_handler() further visits it.
smc_cdc_tx_handler() |smc_release()
if (!conn) |
|
|smc_cdc_tx_dismiss_slots()
| smc_cdc_tx_dismisser()
|
|sock_put(&smc->sk) <- last sock_put,
| smc_sock freed
bh_lock_sock(&smc->sk) (panic) |
To make sure we won't receive any CDC messages after we free the
smc_sock, add a refcount on the smc_connection for inflight CDC
message(posted to the QP but haven't received related CQE), and
don't release the smc_connection until all the inflight CDC messages
haven been done, for both success or failed ones.
Using refcount on CDC messages brings another problem: when the link
is going to be destroyed, smcr_link_clear() will reset the QP, which
then remove all the pending CQEs related to the QP in the CQ. To make
sure all the CQEs will always come back so the refcount on the
smc_connection can always reach 0, smc_ib_modify_qp_reset() was replaced
by smc_ib_modify_qp_error().
And remove the timeout in smc_wr_tx_wait_no_pending_sends() since we
need to wait for all pending WQEs done, or we may encounter use-after-
free when handling CQEs.
For IB device removal routine, we need to wait for all the QPs on that
device been destroyed before we can destroy CQs on the device, or
the refcount on smc_connection won't reach 0 and smc_sock cannot be
released.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Reported-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found smc_llc_send_link_delete_all() sometimes wait
for 2s timeout when testing with RDMA link up/down.
It is possible when a smc_link is in ACTIVATING state,
the underlaying QP is still in RESET or RTR state, which
cannot send any messages out.
smc_llc_send_link_delete_all() use smc_link_usable() to
checks whether the link is usable, if the QP is still in
RESET or RTR state, but the smc_link is in ACTIVATING, this
LLC message will always fail without any CQE entering the
CQ, and we will always wait 2s before timeout.
Since we cannot send any messages through the QP before
the QP enter RTS. I add a wrapper smc_link_sendable()
which checks the state of QP along with the link state.
And replace smc_link_usable() with smc_link_sendable()
in all LLC & CDC message sending routine.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received frames have FCS truncated. There is no need
to subtract FCS length from the statistics.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
'ndev' is a managed resource allocated with devm_alloc_etherdev(), so there
is no need to call free_netdev() explicitly or there will be a double
free().
Simplify all error handling paths accordingly.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we build for mips, we meet following error. l1_init error with
multiple definition. Some architecture devices usually marked with
l1, l2, lxx as the start-up phase. so we change the mISDN function
names, align with Isdnl2_xxx.
mips-linux-gnu-ld: drivers/isdn/mISDN/layer1.o: in function `l1_init':
(.text+0x890): multiple definition of `l1_init'; \
arch/mips/kernel/bmips_5xxx_init.o:(.text+0xf0): first defined here
make[1]: *** [home/mips/kernel-build/linux/Makefile:1161: vmlinux] Error 1
Signed-off-by: wolfgang huang <huangjinhui@kylinos.cn>
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix user-space builds if it includes /usr/include/linux/nfc.h before
some of other headers:
/usr/include/linux/nfc.h:281:9: error: unknown type name ‘size_t’
281 | size_t service_name_len;
| ^~~~~~
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace sa_family_t with __kernel_sa_family_t to fix the following
linux/nfc.h userspace compilation errors:
/usr/include/linux/nfc.h:266:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
/usr/include/linux/nfc.h:274:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
Fixes: 23b7869c0f ("NFC: add the NFC socket raw protocol")
Fixes: d646960f79 ("NFC: Initial LLCP support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matthias-Christian Ott <ott@mirix.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In smc_wr_tx_send_wait() the completion on index specified by
pend->idx is initialized and after smc_wr_tx_send() was called the wait
for completion starts. pend->idx is used to get the correct index for
the wait, but the pend structure could already be cleared in
smc_wr_tx_process_cqe().
Introduce pnd_idx to hold and use a local copy of the correct index.
Fixes: 09c61d24f9 ("net/smc: wait for departure of an IB message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
