Instead of manually create and handler kernel thread switch to threaded
IRQ and let kernel IRQ core manage thread for us.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Let compiler figure out which ones makes most sense to inline.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add __devinit/__devexit sections annotations so parts of code could be
discarded after completing driver initialization.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
So that it has proper symlink to the containing module in sysfs.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of using legacy PM interfaces switch to using dev_pm_ops.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Several protocol initialization routines can fail after they set up
psmouse methods, such as reconnect and disconnect. This may lead to
these stale methods used with different protocol that they were
intended to be used for and may cause unpredictavle behavior and/or
crashes.
Make sure we start with a clean slate before executing each and every
protocol detection and/or initialization routine.
Reported-by: Paul Fox <pgf@laptop.org>
Acked-by: Tai-hwa Liang <avatar@sentelic.com>
Acked-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If there is a full packet in the buffer, and we overflow that buffer
right after checking for that condition, it would have been possible
for us to block indefinitely (rather, until the next full packet) even if
the file was marked as O_NONBLOCK.
Cc: Jeff Brown <jeffbrown@android.com>
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this, it was possible for the reader to get ahead of packet_head.
If the input device generated a partial packet *right* after the reader
got ahead, then we can get into a situation where the device is marked
readable, but read always returns 0 until the next packet is finished
(i.e a SYN is generated by the input driver).
This situation can also happen if we overflow the buffer while a reader
is trying to read an event out.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When runtime power management is enabled put the Samsung keypad driver
into suspend mode with wakeups disabled whenever the device is open but
a key is not actually been pressed. As well as saving a trivial amount of
power this will support the use of SoC wide idle modes which put the entire
device into a retention mode and use explicit wakeup sources to exit.
Since not all of the interrupt controllers used with the driver support
set_irq_wake() (though they all do the right thing) and there's a nasty
WARN() when we disable wake after failing to enable it keep track of the
current wake status from runtime PM and only disable wake if we managed
to enable it; I'm not entirely sure why this doesn't affect the existing
uses of the API in the driver.
System suspend is unaffected as the driver core will runtime resume any
suspended devices prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
drivers/input/keyboard/samsung-keypad.c
This adds a simple device tree binding to the tegra keyboard controller.
Also, mark the default keymap as __devinitdata since it is not referenced
after boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some displays from AUO have a so called in-cell touchscreen, meaning it
is built directly into the display unit.
Touchdata is gathered through PIXCIR Tango-ICs and processed in an
Atmel ATmega168P with custom firmware. Communication between the host
system and ATmega is done via I2C.
Devices using this touch solution include the Dell Streak5 and the family
of Qisda ebook readers.
The driver reports single- and multi-touch events including touch area
values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for Sharp's GP2AP002A00F proximity sensor. The
proximity is measured as a binary switch, i.e. an object is either
detected or not detected. Hence, this driver is implemented as a switch
that reports SW_FRONT_PROXIMITY.
Reviewed-by: Datta Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: Courtney Cavin <courtney.cavin@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts mc13783-pwrbutton to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.
Also staticise mc13783_pwrbutton_driver which is not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
