Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds "non-removable" property of MMC host where the eMMC device
is for Tegra platform.
And the "keep-power-in-suspend" property was used for the SDIO device that
need this to go into suspend mode (e.g. BRCM43xx series).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the power gpio key to DT and enable the wakeup of the gpio key
for the device. The Seaboard and paz00 already had the power gpio key
binding and the power key of Whistler was on KBC. So these boards' device
tree didn't include in this patch.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Set "regulator-always-on" for the SD slot on Dalmore, so that SD cards
work. This used to work, since this regulator is on by default, but was
broken by commit "ARM: tegra: dalmore: add TPS65090 node", since that
didn't specify always-on for this regulator.
In the long run, the regulators should all be hooked up to the SDHCI
device nodes. However, we haven't done that for any of the Tegra boards
yet, so to be consistent, this patch simply forces the regulator on,
rather than hooking it up and making it work differently to other boards.
Reported-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 reference platform Dalmore has voltage switch
regulators which are controlled by the Tegra GPIOs.
Add DT node for fixed regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 reference platform, Dalmore, uses the TPS65090 as
secondary PMICs which is mainly act as voltage switch regulator
controlled by i2c communication.
Add DT node for TPS65090.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dalmore uses the TPS51632 as CPU regulator. The device is connected
on I2C5.
Add DT node for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds the node for the bq20z45 I2C gas gauge which is
compatible with the sbs-battery power supply driver.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add documentation for device tree binding of NVIDIA's Tegra I2C
controller driver.
Describing all compatible values used for different Tegra SoCs
in details in this documentation.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed a couple typos, trimmed examples]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 6 SPI controllers. These controllers are
redesign on T114 with different register interface.
Add DT entry for spi controllers and make it compatible with
"nvidia,tegra114-spi", since they are a new incompatible design.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed reg property for 3rd SPI controller]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 SoCs have the matrix keyboard controller which
supports 11x8 type of matrix. The number of rows and columns
are configurable.
Add DT entry for KBC controller with compatibility as "nvidia,tegra114-kbc".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add APB DMA requestor and serial aliases for serial controller.
There are two serial drivers i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.
The simple serial driver is selected by compatible value
"nvidia,tegra114-uart", "nvidia,tegra20-uart", and the APB DMA based
driver is selected by compatible value "nvidia,tegra114-hsuart",
"nvidia,tegra30-hsuart".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 5 I2C controllers. These controllers have the
following changes which makes incompatible with previous hardware:
- Single clock source to I2C controller.
- Interrupt support for per packet transfer.
Add DT entry for I2C controllers and make it compatible with
"nvidia,tegra114-i2c".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed location of status property for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 32 channels APB DMA controller. Add DT entry for
APB DMA controllers and make it compatible with "nvidia,tegra114-apbdma".
Tegra114 DMA controller is not compatible with Tegra30/Tegra20 DMA
controller driver as in Tegra114, the global pause also clock gate the
DMA register and hence it iw not possible to write the DMA register
with global pause.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed DT node order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds a device tree node for the four PWM controllers present
on Tegra114.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.
Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: Andrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dalmore has a built-in eMMC device and a user-accessible SD card slot.
Add device tree nodes to enable these.
Based on changes by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: added commit description, fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds in the SDHCI nodes for the busses supported on Tegra114
boards.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
[Rhyland added clk refs to & reordered sdhci nodes and removed spaces]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The USB PHY nodes are all grouped together rather than being sorted based
on reg address like all other nodes fix this.
I apologize for the churn; I should have noticed this during review of the
patches that caused this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A gap exists in the binding's clock ID definitions. Fix the clock driver
to be consistent. This allows pclk to be looked up through device tree
and prevents:
ERROR: could not get clock /pmc:pclk(0)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
