Since gso_skb is re-used for qdisc_peek_dequeued(), and this skb is
counted in the qdisc->q.qlen, it has to be kfreed during qdisc_reset()
when qlen is zeroed.
With help from David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 support to SH and DH schedulers. I hope this simple IPv6 address
hashing is good enough. The 128 bit are just XORed into 32 before hashing
them like an IPv4 address.
Signed-off-by: Julius Volz <julius.volz@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This documentation patch hopes to clarify that the '+' was only needed
for Fedora 7 and Red Hat Enterprise Linux 5.0 and 5.1. After that the
IP addreses could be added as a comma separated list just like the
module option.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The smc_drv_probe() is the platform_driver probe function and it is only
called during init. Further, it calls smc_probe() which is marked as __init
already.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This eliminates the following often-generated warning from my 64 bit
Opteron SMP test stand:
eth0: too many iterations (6) in nv_nic_irq
According to the web, the problem is that the forcedeth driver has a
too-low value for max_interrupt_work. Grepping the kernel I see that
forcedeth has the second lowest value of all ethernet drivers (ie, 6).
Most are in the 20-40 range. So this patch increases this a bit, from 6
to 15 (at 15 forcedeth becomes the driver with third-lowest
max_interrupt_work value).
My test stand, which used to print out the above warnings repetitively
whenever it was under heavy net load, no longer does so.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do some cleanup on timer usage in this driver:
* Use round_jiffies to align wakeups and reduce power.
* Remove atl1_watchdog which does nothing but rearm itself
* Use setup_timer() function
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is now a net_device_stats structure inside net_device that should
be used if possible by devices. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After removing netem classful functionality we are sure its inner
qdisc is tfifo, so we can replace qdisc->ops->requeue() method with
open code. After this patch there are no more ops->requeue() users.
The idea of this patch is by Patrick McHardy.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy noticed that: "a lot of the functionality of netem
requires the inner tfifo anyways and rate-limiting is usually done
on top of netem. So I would suggest so either hard-wire the tfifo
qdisc or at least make the assumption that inner qdiscs are
work-conserving.", and later: "- a lot of other qdiscs still don't
work as inner qdiscs of netem [...]".
So, according to his suggestion, this patch removes classful options
of netem. The main reason of this change is to remove ops->requeue()
method, which is currently used only by netem.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean up net/unix/af_unix.c garbage.c sysctl_net_unix.c
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corey Minyard spotted a missing memory barrier in udp_lib_get_port()
We need to make sure a reader cannot read the new 'sk->sk_next' value
and previous value of 'sk->sk_hash'. Or else, an item could be deleted
from a chain, and inserted into another chain. If new chain was empty
before the move, 'next' pointer is NULL, and lockless reader can
not detect it missed following items in original chain.
This patch is temporary, since we expect an upcoming patch
to introduce another way of handling the problem.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
