Minimum gcc version is 3.2 now. However, with likely profiling, even
modern gcc versions cannot always eliminate the call.
Replace the placeholder functions with the more conventional empty static
inlines, which should be optimal for everyone.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can use the global ZVC counters to establish the exact size of the LRU
and the free pages. This allows a more accurate determination of the dirty
ratio.
This patch will fix the broken ratio calculations if large amounts of
memory are allocated to huge pags or other consumers that do not put the
pages on to the LRU.
Notes:
- I did not add NR_SLAB_RECLAIMABLE to the calculation of the
dirtyable pages. Those may be reclaimable but they are at this
point not dirtyable. If NR_SLAB_RECLAIMABLE would be considered
then a huge number of reclaimable pages would stop writeback
from occurring.
- This patch used to be in mm as the last one in a series of patches.
It was removed when Linus updated the treatment of highmem because
there was a conflict. I updated the patch to follow Linus' approach.
This patch is neede to fulfill the claims made in the beginning of the
patchset that is now in Linus' tree.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The nr_cpu_ids value is currently only calculated in smp_init. However, it
may be needed before (SLUB needs it on kmem_cache_init!) and other kernel
components may also want to allocate dynamically sized per cpu array before
smp_init. So move the determination of possible cpus into sched_init()
where we already loop over all possible cpus early in boot.
Also initialize both nr_node_ids and nr_cpu_ids with the highest value they
could take. If we have accidental users before these values are determined
then the current valud of 0 may cause too small per cpu and per node arrays
to be allocated. If it is set to the maximum possible then we only waste
some memory for early boot users.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new mm function apply_to_page_range() which applies a given function to
every pte in a given virtual address range in a given mm structure. This is a
generic alternative to cut-and-pasting the Linux idiomatic pagetable walking
code in every place that a sequence of PTEs must be accessed.
Although this interface is intended to be useful in a wide range of
situations, it is currently used specifically by several Xen subsystems, for
example: to ensure that pagetables have been allocated for a virtual address
range, and to construct batched special pagetable update requests to map I/O
memory (in ioremap()).
[akpm@linux-foundation.org: fix warning, unpleasantly]
Signed-off-by: Ian Pratt <ian.pratt@xensource.com>
Signed-off-by: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@waste.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPSC serial driver assumes that interrupt is always on to pick up the
DMA transmit ops that aren't submitted while the DMA engine is active.
However when irqs are off for a period of time such as operations under
kernel crash dump console messages do not show up due to additional DMA ops
are being dropped. This makes console writes to process through all the tx
DMAs queued up before submitting a new request.
Also, the current locking mechanism does not protect the hardware registers
and ring buffer when a printk is done during the serial write operations.
The additional per port transmit lock provides a finer granular locking and
protects registers being clobbered while printks are nested within UART
writes.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At present, the serial core always allows setserial in userspace to change the
port address, irq and base clock of any serial port. That makes sense for
legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports
at peculiar addresses. In these cases, the kernel code configuring the ports
must know exactly where they are, and their clocking arrangements (which can
be unusual on embedded boards). It doesn't make sense for userspace to change
these settings.
Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port
structure. If this flag is set when the serial port is configured, any
attempts to alter the port's type, io address, irq or base clock with
setserial are ignored.
In addition this patch uses the new flag for on-chip serial ports probed in
arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports
probed by drivers/serial/of_serial.c.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial driver patch for the PMC-Sierra MSP71xx devices.
There are three different fixes:
1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard
16550 in that the THRE interrupt will not re-assert itself simply by
disabling and re-enabling the THRI bit in the IER, it is only re-enabled
if a character is actually sent out.
It appears that the "8250-uart-backup-timer.patch" in the "mm" tree
also fixes it so we have dropped our initial workaround. This patch now
needs to be applied on top of that "mm" patch.
2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature
which causes a new Busy Detect interrupt to be generated if it's busy
when the LCR is written. This fix saves the value of the LCR and
rewrites it after clearing the interrupt.
3 Workaround for interrupt/data concurrency issue: The SoC needs to
ensure that writes that can cause interrupts to be cleared reach the UART
before returning from the ISR. This fix reads a non-destructive register
on the UART so the read transaction completion ensures the previously
queued write transaction has also completed.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI drivers have the new_id file in sysfs which allows new IDs to be added
at runtime. The advantage is to avoid re-compilation of a driver that
works for a new device, but it's ID table doesn't contain the new device.
This mechanism is only meant for testing, after the driver has been tested
successfully, the ID should be added in source code so that new revisions
of the kernel automatically detect the device.
The implementation follows the PCI implementation. The interface is documented
in Documentation/pcmcia/driver.txt. Computations should be done in userspace,
so the sysfs string contains the raw structure members for matching.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a minor correctness fix: since the at91_cf driver probe() routine
is in the init section, it should use platform_driver_probe() instead of
leaving that pointer around in the driver struct after init section
removal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduce krealloc() that reallocates memory while keeping the contents
unchanged. The allocator avoids reallocation if the new size fits the
currently used cache. I also added a simple non-optimized version for
mm/slob.c for compatibility.
[akpm@linux-foundation.org: fix warnings]
Acked-by: Josef Sipek <jsipek@fsl.cs.sunysb.edu>
Acked-by: Matt Mackall <mpm@selenic.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was broken. It adds complexity, for no good reason. Rather than
separate __pa() and __pa_symbol(), we should deprecate __pa_symbol(),
and preferably __pa() too - and just use "virt_to_phys()" instead, which
is more readable and has nicer semantics.
However, right now, just undo the separation, and make __pa_symbol() be
the exact same as __pa(). That fixes the bugs this patch introduced,
and we can do the fairly obvious cleanups later.
Do the new __phys_addr() function (which is now the actual workhorse for
the unified __pa()/__pa_symbol()) as a real external function, that way
all the potential issues with compile/link-time optimizations of
constant symbol addresses go away, and we can also, if we choose to, add
more sanity-checking of the argument.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (66 commits)
KVM: Remove unused 'instruction_length'
KVM: Don't require explicit indication of completion of mmio or pio
KVM: Remove extraneous guest entry on mmio read
KVM: SVM: Only save/restore MSRs when needed
KVM: fix an if() condition
KVM: VMX: Add lazy FPU support for VT
KVM: VMX: Properly shadow the CR0 register in the vcpu struct
KVM: Don't complain about cpu erratum AA15
KVM: Lazy FPU support for SVM
KVM: Allow passing 64-bit values to the emulated read/write API
KVM: Per-vcpu statistics
KVM: VMX: Avoid unnecessary vcpu_load()/vcpu_put() cycles
KVM: MMU: Avoid heavy ASSERT at non debug mode.
KVM: VMX: Only save/restore MSR_K6_STAR if necessary
KVM: Fold drivers/kvm/kvm_vmx.h into drivers/kvm/vmx.c
KVM: VMX: Don't switch 64-bit msrs for 32-bit guests
KVM: VMX: Reduce unnecessary saving of host msrs
KVM: Handle guest page faults when emulating mmio
KVM: SVM: Report hardware exit reason to userspace instead of dmesg
KVM: Retry sleeping allocation if atomic allocation fails
...
utrace removes the ptrace_message field in task_struct. Move our use
of this field into a new member in thread_info called "syscall"
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I have found small bug in mconf, when you run it without any argument it
will sigsegv.
Without patch:
$ scripts/kconfig/mconf
Segmentation fault
With patch:
$ scripts/kconfig/mconf
can't find file (null)
Signed-off-by: Marcin Garski <mgarski@post.pl>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To introduce support for source in one directory but output files
in another directory during a non O= build prefix all paths
with $(src) repsectively $(obj).
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Sample:
config FOO
bool "This is foo"
depends on BAR
config BAR
bool "This is bar"
depends on FOO
This will result in following error message:
error: found recursive dependency: FOO -> BAR -> FOO
And will then exit with exit code equal 1 so make will stop.
Inspired by patch from: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix typo in cifs readme from previous commit
[CIFS] Make sec=none force an anonymous mount
[CIFS] Change semaphore to mutex for cifs lock_sem
[CIFS] Fix oops in reset_cifs_unix_caps on reconnect
[CIFS] UID/GID override on CIFS mounts to Samba
[CIFS] prefixpath mounts to servers supporting posix paths used wrong slash
[CIFS] Update cifs version to 1.49
[CIFS] Replace kmalloc/memset combination with kzalloc
[CIFS] Add IPv6 support
[CIFS] New CIFS POSIX mkdir performance improvement (part 2)
[CIFS] New CIFS POSIX mkdir performance improvement
[CIFS] Add write perm for usr to file on windows should remove r/o dos attr
[CIFS] Remove unnecessary parm to cifs_reopen_file
[CIFS] Switch cifsd to kthread_run from kernel_thread
[CIFS] Remove unnecessary checks
