Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a race condition that caused the HWA_HC interface probe
function to occasionally fail. The HWA_HC would attempt to register
itself with the HWA_RC by searching for a uwb_rc class device with the
same parent device ptr. If the probe function for the HWA_RC interface
had yet to run, the uwb_rc class device would not have been created
causing the look up to fail and the HWA_HC probe function to return an
error causing the device to be unusable.
The fix is for the HWA to delay registering with the HWA_RC until
receiving the command from userspace to start the wireless channel. It
is the responsibility of userspace to ensure that the uwb_rc class
device has been created before starting the HWA channel.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From Kukjin Kim:
cleanup and removing dead code for only support DT for exynos
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
* tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (35 commits)
ARM: EXYNOS: Remove remaining dead code after non-DT support removal
ARM: EXYNOS: Remove legacy L2X0 initialization
ARM: EXYNOS: Use exynos_init_io() as map_io callback
ARM: EXYNOS: Remove custom init_irq callbacks
ARM: EXYNOS: Remove mach/regs-usb-phy.h header
thermal: exynos: Support both EXYNOS4X12 SoCs
ARM: EXYNOS: Remove unused base addresses from mach/map.h header
ARM: EXYNOS: Remove mach/irqs.h header
ARM: EXYNOS: Select SPARSE_IRQ for Exynos
ARM: SAMSUNG: Make legacy MFC support code depend on SAMSUNG_ATAGS
ARM: EXYNOS: Remove mach/regs-gpio.h header
ARM: EXYNOS: Remove mach/gpio.h
ARM: EXYNOS: Remove setup-i2c0.c
ARM: EXYNOS: Do not select legacy Kconfig symbols any more
ARM: SAMSUNG: Include most of mach/ headers conditionally
ARM: EXYNOS: Decouple ARCH_EXYNOS from PLAT_S5P
USB: Check for ARCH_EXYNOS separately
platform: Check for ARCH_EXYNOS separately
ARM: SAMSUNG: Compile legacy IRQ and GPIO PM code only with ATAGS support
ARM: EXYNOS: Provide compatibility stubs for PM code in pm-core.h header
...
Conflicts:
arch/arm/mach-exynos/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sarah writes:
xhci: Remove BUG() calls from the driver.
Hi Greg,
This patchset removes instances of BUG() from the xHCI driver. It adds code to
gracefully handle failures by returning standard error values, and changing the
driver to handle those failure cases. These are against Greg's usb-next
branch, and are not marked for stable.
Please queue for 3.11.
Sarah Sharp
ARCH_EXYNOS is going to be excluded from PLAT_S5P, so it must be checked
separately in Exynos-related Kconfig entries.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes a double assignment of .start in struct hc_driver
ehci_msp_hc_driver and also makes the code look more tidy.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For PHY mode, the PHYs must be brought out of reset
before the EHCI controller is started.
This patch fixes the issue where USB devices are not found
on Beagleboard/Beagle-xm if USB has been started previously
by the bootloader. (e.g. by "usb start" command in u-boot)
Tested on Beagleboard, Beagleboard-xm and Pandaboard.
Issue present on 3.10 onwards.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under some circumstances it happens that the connected PHY can't be
powered up properly, in which case the cleanup path currently crashes
because it checks the tegra->transceiver field using !IS_ERR(), which
will succeed because it is in fact NULL. Dereferencing that pointer
causes an oops in tegra_ehci_probe().
This patch fixes the issue by adding an additional label into the
cleanup path to separately take down the PHY and the transceiver.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Tegra on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
[swarren, reworked Manjunath's patches to split them more logically,
minor re-order of added lines to better match layout of other split-up
HCD drivers and existing code, add MODULE_DEVICE_TABLE, fix
MODULE_LICENSE, adapted to change in earlier patches which removed the
ehci_driver_overrides addition, removed all PM code and solved circular
dependencies.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra EHCI driver directly calls various functions in the Tegra USB
PHY driver. The reverse is also true; the PHY driver calls into the EHCI
driver. This is problematic when the two are built as modules.
The calls from the PHY to EHCI driver were originally added in commit
bbdabdb "usb: add APIs to access host registers from Tegra PHY", for the
following reasons:
1) The register being touched is an EHCI register, so logically only the
EHCI driver should touch it.
2) (1) implies that some locking may be needed to correctly implement the
r/m/w access to this shared register.
3) We were expecting to pass only the PHY register space to the Tegra PHY
driver, and hence it would not have access to touch the shared
registers.
To solve this, that commit added functions in the EHCI driver to touch the
shared register on behalf of the PHY driver.
In practice, we ended up not having any locking in the implementaiton of
those functions, and I've been led to believe this is safe. Equally, (3)
did not happen either. Hence, it is possible for the PHY driver to touch
the shared register directly.
Given that, this patch moves the code to touch the shared register back
into the PHY driver, to eliminate the module problems. If we actually
need locking or co-ordination in the future, I propose we put the lock
support into some pre-existing core module, or into a third separate
module, in order to avoid the circular dependencies.
I apologize for my contribution to code churn here.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PM routines in ehci-tegra.c use APIs such as ehci_reset(),
ehci_halt(), and ehci_tdi_reset() that would need to be exported to
convert ehci-tegra.c into a separate module from ehci-hcd.c. However,
we'd prefer not to export them.
Instead, simply remove all power management functionality. Runtime PM
was disabled since it didn't work correctly, and system suspend isn't
yet supported in a meaningful way. So, this change doesn't lose any
functionality.
Hopefully the power management logic can be reimplemented in a cleaner
way in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to split ehci-hcd.c into separate modules, handshake() must be
exported. Rename the symbol to add an ehci_ prefix, to avoid any naming
clashes.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
[swarren, split Manjunath's patches more logically, limit this change
to export just handshake()]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for scatter gather DMA to the wire adapter and
updates the HWA to advertise support for SG transfers. This allows the
block layer to submit transfer requests to the HWA HC without first
breaking them up into PAGE_SIZE requests.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From Simon Horman:
Renesas USB updates for v3.11
These updates are by Sergei Shtylyov to clean-up USB support
present for R8A7779/Marzen and then extend USB support coverage to
R8A7778/BOCK-W.
* tag 'renesas-phy-rcar-usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: BOCK-W: add USB support
ARM: shmobile: r8a7778: add USB support
phy-rcar-usb: add R8A7778 support
phy-rcar-usb: handle platform data
ARM: shmobile: Marzen: pass platform data to USB PHY device
phy-rcar-usb: add platform data
phy-rcar-usb: correct base address
ARM: shmobile: r8a7779: remove USB PHY 2nd memory resource
phy-rcar-usb: remove EHCI internal buffer setup
ARM: shmobile: r8a7779: setup EHCI internal buffer
ehci-platform: add pre_setup() method to platform data
ARM: shmobile: Marzen: move USB EHCI, OHCI, and PHY devices to R8A7779 code
Conflicts:
arch/arm/mach-shmobile/board-marzen.c
arch/arm/mach-shmobile/setup-r8a7778.c
Signed-off-by: Olof Johansson <olof@lixom.net>
We may have more speed types in the future, so fail gracefully, rather
than causing the kernel to panic.
BUG() was called if the device speed was unknown when setting max packet
size. Set the max packet size at the same time as the slot speed and
get rid of one switch statement with BUG() option completely.
[Note: Sarah merged a patch that she wrote that touched the
xhci_setup_addressable_virt_dev function with this patch from Mathias
for clarity.]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Fail gracefully, instead of causing the kernel to panic, if the input
control context doesn't have the right type (XHCI_CTX_TYPE_INPUT). Push
finding the pointer to the input control context up into functions that
can fail.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
It's horrible coding style to panic the kernel when someone passes you
an argument value you didn't expect. In the future, we may want to add
additional context types, so it's better to gracefully handle additional
context types instead of panicking.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
