MMIO log traces obtained using the Broadcom wl hybrid driver show that
the RETRY_TIMEOUT register (0x41) in PCI configuration space is cleared
if non-zero. Similar code found in other drivers such as ipw2100 show
this operation is needed to keep PCI Tx retries from interfering with
C3 CPU state. There are no known cases where omission of this code has
caused a problem, but this patch is offered just in case such a situation
occurs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse warning:
CHECK drivers/net/wireless/ath/ath5k/base.c
drivers/net/wireless/ath/ath5k/base.c:569:6: warning: symbol
'ath5k_update_bssid_mask_and_opmode' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse warning:
CHECK drivers/net/wireless/ath/key.c
drivers/net/wireless/ath/key.c:110:6: warning: symbol
'ath_hw_set_keycache_entry' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse warning:
CHECK drivers/net/wireless/ath/key.c
drivers/net/wireless/ath/key.c:70:6: warning: symbol 'ath_hw_keysetmac' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_set_txpowerlimit gets an extra boolean parameter that - if set -
causes the rate txpower table and the regulatory limit to be calculated
and stored, without changing hardware registers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same is done for the older chip families as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Include the channel utilization (busy, rx, tx) in the survey results.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to Felix Fietkau <nbd@openwrt.org> "ath9k_hw: optimize all descriptor
access functions" (13db2a80244908833502189a24de82a856668b8a).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the current rate control selection method the median function is
nowhere used, so remove it.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because all of the descriptor data structures are marked as __packed, GCC
assumes the worst case wrt. alignment and generates unaligned load/store
instructions on MIPS for access to all fields.
Since descriptors always have to be 4-byte-aligned, we can just mark the
data structures with __aligned(4), which allows GCC to generate much more
efficient code.
Verified through disassembly and OProfile comparisons.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver uses the legacy PCI power management (suspend
and resume) callbacks that apparently cause intermittent problems
to happen (the adapter sometimes doesn't resume correctly on my
Acer Ferrari One). Make it use the new PCI PM and let the PCI core
code handle the PCI-specific details of power transitions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse complaint:
CHECK drivers/net/wireless/ath/ath9k/debug.c
drivers/net/wireless/ath/ath9k/debug.c:548:34: warning: symbol 'aphy' shadows an earlier one
drivers/net/wireless/ath/ath9k/debug.c:491:26: originally declared here
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the timer_next argument to ath9k_gen_timer_start is behind the tsf value,
tsf + timer_period is used, which is what ath_btcoex_period_timer was setting
it to.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI needs the RSSI average only in station mode, and only for tracking
the signal strength of beacons of the AP that it is connected to.
Adjust the code to track on the beacon RSSI, and store the average of that
in the ath_wiphy struct.
With these changes, we can get rid of this extra station lookup in the
rx path, which saves precious CPU cycles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disassembly shows, that at least on MIPS, the compiler generates a lot of
memory accesses to the same location in the descriptor field parsing.
Since it is operating on uncached memory, this can be quite expensive in
this hot path.
Change the code a bit to help the compiler optimize it properly, and get
rid of some unused fields in the ath_tx_status struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->config.rx_intr_mitigation does not need to be checked before checking
the rx interrupt mask for AR_ISR_RXMINTR or AR_ISR_RXINTM, as those
interrupts will be masked out if rx interrupt mitigation is disabled.
Avoid reading AR_ISR_S5_S twice by reordering the code to be more concise.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OProfile showed that ath9k was spending way too much time in
ath9k_hw_set_interrupts. Since most of the interrupt mask changes only
need to globally enable/disable interrupts, it makes sense to split
this part into separate functions, replacing all calls to
ath9k_hw_set_interrupts(ah, 0) with ath9k_hw_disable_interrupts(ah).
ath9k_hw_set_interrupts(ah, ah->imask) only gets changed to
ath9k_hw_enable_interrupts(ah), whenever ah->imask was not changed
since the point where interrupts were disabled.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
