The Freescale PCI-e RC poses as a transparent bridge, but does not
implement the IO_BASE or IO_LIMIT registers in the config space. This
means that the code which initializes the bridge resources ends up
setting the IO resources erroneously. Add quick_fsl_pcie_transparent()
to handle this.
This change sets RC of mpc8641 to be a transparent bridge
for legacy I/O access and initializes the RC bridge resources
from the device tree.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In pcibios_fixup_bus(), bridges that are subordinate
to transparent bridges were still relocating their
IORESOURCE_IO and IO_RESOURCE_MEM start and end values.
Fix this by preventing the transparent bridge from
relocating the start and end values, thus allowing the
subordinate non-transparent bridge full molestation rights.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set IDE in ULI1575 to not 100% native mode, which forces
the IDE driver to probe the irq itself.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI-e controllers have an issue in that they use the
PCI_PRIMARY_BUS register in the virtual P2P bridge to determine which
bus number to match on when generating a type 0 config cycle. The
issue is if we are renumbering bus numbers to match Linux we will try
setting the PCI_PRIMARY_BUS and will not know which bus number to use
for generating type 0 config cycles. We surpress writing the register
in the P2P bridge and always keep it at zero.
In the future when proper PCI domain support is working we should be
able to remove this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The generic PCI config ops indirect support for ppc32 covers only two
cases (implicit vs explicit) type 0/1 config cycles via set_cfg_type.
Added a indirect_type bit mask to handle other variants.
Added support for PCI-e extended registers and moved the cfg_type
handling into the bit mask for ARCH=powerpc. We can also use this to
handle indirect quirks.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds device nodes for the PCI bridges as well as the ISA devices on
the newer revision MPC8641HPCN. It also adds the PCI ranges to the soc
node so that address translation for the ISA devices works properly.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added self_busno to pci_controller and indirect PCI ops to be set by
board code to indicate which bus number to use when talking to the PHB.
By default we use zero since the majority of controllers that have
implicit mechanisms to talk to the PHBs use a bus number of zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user of the fsl_pcie code doesn't set bus_offset and 82xx doesn't
require it either. Remove the places in the code that reference it so
we can remove it all together.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have the pci_controller in the exclude function we can easy
figure out if the bus number is the PHB or not. The old style of using a
variable setup at init time was actually broken and would only work in
specific cases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The hose->bus_offset is only used for PCI config cycles and the 52xx PCI
config code doesn't actually ever set bus_offset to a non-zero value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles. They handle producing them by implicitly looking at the
bus, devfn.
The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The TSI108 code and the 32 bit powermac and chrp platforms
have dependency on PCI that is not easy or desirable to get rid
of.
The easiest fix is to always select CONFIG_PCI if one of those
platforms is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.
The easiest fix is to just remove all these definitions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cores used in the MPC82xx/83xx/86xx embedded controllers are very similar
to those in the 32 bit general-purpose processors, so it makes sense to
treat them as the same CPU family.
Choosing between the embedded platforms and the multiplatform code is
now done in the platform menu, but functionally everything stays the
same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A strict reading of the flattened device tree format defined in
booting-without-of.txt does in fact require that all the tags defining
properties for a node go before any definitions of subnodes, however
it's not particularly emphasised. Although allowing intermingled
properties and subnodes would not be ambiguous in meaning, the kernel
parser does currently require that properties precede subnodes.
Furthermore, keeping this constraint makes life easier for various
device tree scanning tools.
Therefore, re-emphasise in booting-without-of.txt that this is a
strict requirement of the flattened device tree format.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-powerpc/processor.h declares, and arch/ppc/platforms/prep_setup.c
defines variables ucBoardRev, ucBoardRevMaj and ucBoardRevMin which
are used nowhere in the current kernel (neither in arch/ppc nor
arch/powerpc). This removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 2e60161337 split up
arch/powerpc/boot/of.c so that some OF functions can be used on
platforms that don't want to use the overall OF platform boot code.
This is useful on things like PReP which can have an OF implementation
which is useful for debugging output, but inadequate for booting.
However, that commit didn't export quite enough things to make a
usable OF console on a non-OF system. In particular, the device tree
manipulation performed to initialize the OF console code must
explicitly use the OF device tree, rather than the flattened device
tree, even if the system is otherwise booting using a flattened device
tree. This makes it so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 3d5134ee83 left debugging turned on
in arch/powerpc/kernel/pci_64.c. This turns it off again.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
