The command:
find ./include/linux/soc/qcom/ | xargs ./scripts/kernel-doc -none
reports:
./include/linux/soc/qcom/qmi.h:26: warning: cannot understand function prototype: 'struct qmi_header '
./include/linux/soc/qcom/qmi.h:101: warning: cannot understand function prototype: 'struct qmi_response_type_v01 '
./include/linux/soc/qcom/irq.h:19: warning: expecting prototype for QCOM specific IRQ domain flags that distinguishes the handling of wakeup(). Prototype was for IRQ_DOMAIN_FLAG_QCOM_PDC_WAKEUP() instead
./include/linux/soc/qcom/apr.h:126: warning: Function parameter or member '__apr_driver' not described in 'module_apr_driver'
./include/linux/soc/qcom/apr.h:126: warning: Excess function parameter '__aprbus_driver' description in 'module_apr_driver'
./include/linux/soc/qcom/llcc-qcom.h:43: warning: cannot understand function prototype: 'struct llcc_slice_desc '
./include/linux/soc/qcom/llcc-qcom.h:60: warning: cannot understand function prototype: 'struct llcc_edac_reg_data '
./include/linux/soc/qcom/llcc-qcom.h:86: warning: cannot understand function prototype: 'struct llcc_drv_data '
Address all those warnings by:
- prefixing kernel-doc descriptions for structs with the keyword 'struct',
- turning a kernel-doc comment that does not follow the kernel-doc syntax
into a normal comment, and
- correcting a parameter name in a kernel-doc comment.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210327065642.11969-3-lukas.bulwahn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released() function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not belong into
any other subsystem, most of them living in drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere"
* tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (89 commits)
soc: aspeed: socinfo: Add new systems
soc: aspeed: snoop: Add clock control logic
memory: tegra186-emc: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
memory: samsung: exynos5422-dmc: Correct function names in kerneldoc
memory: ti-emif-pm: Drop of_match_ptr from of_device_id table
optee: simplify i2c access
drivers: soc: atmel: fix type for same7
tee: optee: remove need_resched() before cond_resched()
soc: qcom: ocmem: don't return NULL in of_get_ocmem
optee: sync OP-TEE headers
tee: optee: fix 'physical' typos
drivers: optee: use flexible-array member instead of zero-length array
tee: fix some comment typos in header files
soc: ti: k3-ringacc: Use of_device_get_match_data()
soc: ti: pruss: Refactor the CFG sub-module init
soc: mediatek: pm-domains: Don't print an error if child domain is deferred
soc: mediatek: pm-domains: Add domain regulator supply
dt-bindings: power: Add domain regulator supply
soc: mediatek: cmdq: Remove cmdq_pkt_flush()
soc: mediatek: pm-domains: Add support for mt8167
...
Define stub functions for the exposed MDT functions in case
QCOM_MDT_LOADER is not configured. This allows users of these
functions to link correctly for COMPILE_TEST builds without
QCOM_SCM enabled.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PM660 and PM660L are a very very common PMIC combo, found on
boards using the SDM630, SDM636, SDM660 (and SDA variants) SoC.
PM660 provides 6 SMPS and 19 LDOs (of which one is unaccesible),
while PM660L provides 5 SMPS (of which S3 and S4 are combined),
10 LDOs and a Buck-or-Boost (BoB) regulator.
The PM660L IC also provides other regulators that are very
specialized (for example, for the display) and will be managed
in the other appropriate drivers (for example, labibb).
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-6-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
Qualcomm SoCs (starting with MSM8998) allow for multiple protection domains
to run on the same Q6 sub-system. This allows for services like ATH10K WLAN
FW to have their own separate address space and crash/recover without
disrupting the modem and other PDs running on the same sub-system. The PDR
helpers introduces an abstraction that allows for tracking/controlling the
life cycle of protection domains running on various Q6 sub-systems.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200312120842.21991-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Some GPIOs are marked as wakeup capable and are routed to another
interrupt controller that is an always-domain and can detect interrupts
even when most of the SoC is powered off. The wakeup interrupt
controller wakes up the GIC and replays the interrupt at the GIC.
Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller
and ensure the wakeup GPIOs are handled correctly.
Co-developed-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-9-git-send-email-ilina@codeaurora.org
----
Changes in v2:
- Address review comments
- Fix Co-developed-by tag
Changes in v1:
- Address minor review comments
- Remove redundant call to set irq handler
- Move irq_domain_qcom_handle_wakeup() to this patch
Changes in RFC v2:
- Rebase on top of GPIO hierarchy support in linux-next
- Set the chained irq handler for summary line
commit 99356b03b4 ("soc: qcom: Make llcc-qcom a generic driver") move
these out of llcc-qcom.h, make the building fails:
drivers/edac/qcom_edac.c:86:40: error: array type has incomplete element type struct llcc_edac_reg_data
static const struct llcc_edac_reg_data edac_reg_data[] = {
^~~~~~~~~~~~~
drivers/edac/qcom_edac.c:87:3: error: array index in non-array initializer
[LLCC_DRAM_CE] = {
^~~~~~~~~~~~
drivers/edac/qcom_edac.c:87:3: note: (near initialization for edac_reg_data)
drivers/edac/qcom_edac.c:88:3: error: field name not in record or union initializer
.name = "DRAM Single-bit",
...
drivers/edac/qcom_edac.c:169:51: warning: struct llcc_drv_data declared inside parameter
list will not be visible outside of this definition or declaration
qcom_llcc_clear_error_status(int err_type, struct llcc_drv_data *drv)
^~~~~~~~~~~~~
This patch move the needed definitions back to include.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 99356b03b4 ("soc: qcom: Make llcc-qcom a generic driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This makes way for adding future llcc versions.
Also pull out the llcc-qcom specific definitions from includes.
Includes path now contains the only definitions that are
to be exposed to other subsystems.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A single file should suffice the need to program the llcc for
various platforms. Get rid of sdm845 specific driver file to
make way for a more generic driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In some software releases the firmware images are not split up with each
loadable segment in it's own file. Check the size of the loaded firmware
to see if it still contains each segment to be loaded, before falling
back to the split-out segments.
Acked-by: Andy Gross <agross@kernel.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently the data structure for llc-slice is devm allocated and
stored as a global but never cleared if the probe function fails.
This is a problem because devm managed memory gets freed on probe
failure the API functions could access the pointer after it has been
freed.
Initialize the drv_data pointer to an error and reset it to an error
on probe failure or device destroy and add protection to the API
functions to make sure the memory doesn't get accessed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Txn IDs created up to INT_MAX cause overflow while storing
the IDs in u16 type supported by QMI header.
Limit the txn IDs max value to U16_MAX to avoid overflow.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add error reporting driver for Single Bit Errors (SBEs) and Double Bit
Errors (DBEs). As of now, this driver supports error reporting for
Last Level Cache Controller (LLCC) of Tag RAM and Data RAM. Interrupts
are triggered when the errors happen in the cache, the driver handles
those interrupts and dumps the syndrome registers.
Signed-off-by: Channagoud Kadabi <ckadabi@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Co-developed-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Cache error reporting controller detects and reports single and
double bit errors on Last Level Cache Controller (LLCC) cache.
Add required support to register LLCC EDAC driver as platform driver,
from LLCC driver.
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Currently, broadcast base is set to end of the LLCC banks, which may
not be correct always. As the number of banks may vary for each chipset
and the broadcast base could be at a different address as well. This info
depends on the chipset, so get the broadcast base info from the device
tree (DT). Add broadcast base in LLCC driver and use this for broadcast
writes.
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Pull remoteproc updates from Bjorn Andersson:
"This adds support for pre-start and post-shutdown hooks for remoteproc
subdevices, refactors the Qualcomm Hexagon support to allow reuse
between several drivers, makes authentication in the MDT file loader
optional, migrates a few format strings to use %pK and migrates the
Davinci driver to use the reset framework"
* tag 'rproc-v4.19' of git://github.com/andersson/remoteproc:
remoteproc/davinci: use the reset framework
remoteproc/davinci: Mark error recovery as disabled
remoteproc: st_slim: replace "%p" with "%pK"
remoteproc: replace "%p" with "%pK"
remoteproc: qcom: fix Q6V5_WCSS dependencies
remoteproc: Reset table_ptr in rproc_start() failure paths
remoteproc: qcom: q6v5-pil: fix modem hang on SDM845 after axis2 clk unvote
remoteproc: qcom q6v5: fix modular build
remoteproc: Introduce prepare and unprepare for subdevices
remoteproc: rename subdev probe and remove functions
remoteproc: Make client initialize ops in rproc_subdev
remoteproc: Make start and stop in subdev optional
remoteproc: Rename subdev functions to start/stop
remoteproc: qcom: Introduce Hexagon V5 based WCSS driver
remoteproc: qcom: q6v5-pil: Use common q6v5 helpers
remoteproc: qcom: adsp: Use common q6v5 helpers
remoteproc: q6v5: Extract common resource handling
remoteproc: qcom: mdt_loader: Make the firmware authentication optional
LLCC (Last Level Cache Controller) provides additional cache memory
in the system. LLCC is partitioned into multiple slices and each
slice gets its own priority, size, ID and other config parameters.
LLCC driver programs these parameters for each slice. Clients that
are assigned to use LLCC need to get information such size & ID of the
slice they get and activate or deactivate the slice as needed. LLCC driver
provides API for the clients to perform these operations.
Signed-off-by: Channagoud Kadabi <ckadabi@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
