The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the st1232 datasheet, the host has to wait for the device
to change into Normal state before accessing registers other than the
Status Register.
If the reset GPIO is wired, the device is powered on during driver
probe, just before reading the resolution. However, the latter may
happen before the device is ready, leading to a probe failure:
st1232-ts 1-0055: Failed to read resolution: -6
Fix this by waiting until the device is ready, by trying to read the
Status Register until it indicates so, or until timeout.
On Armadillo 800 EVA, typically the first read fails with an I2C
transfer error, while the second read indicates the device is ready.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-4-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
st1232_ts_read_data() already reads ts->read_buf_len bytes (8 or 20
bytes) from the touchscreen controller. This was fine when it was used
to read touch point coordinates only, but is overkill for reading the
touchscreen resolution, which just needs 3 bytes.
Optimize transfers by passing the wanted number of bytes.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-3-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before, the maximum coordinates were fixed to (799, 479) or (319, 479),
depending on touchscreen controller type. The driver was changed to
read the actual values from the touchscreen controller, but did not take
into account the returned values are not the maximum coordinates, but
the touchscreen resolution (e.g. 800 and 480).
Fix this by subtracting 1.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-2-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- support for inhibiting input devices at request from userspace. If a
device implements open/close methods, it can also put device into low
power state. This is needed, for example, to disable keyboard and
touchpad on convertibles when they are transitioned into tablet mode
- now that ordinary input devices can be configured for polling mode,
dedicated input polling device implementation has been removed
- GTCO tablet driver has been removed, as it used problematic custom
HID parser, devices are EOL, and there is no interest from the
manufacturer
- a new driver for Dialog DA7280 haptic chips has been introduced
- a new driver for power button on Dell Wyse 3020
- support for eKTF2132 in ektf2127 driver
- support for SC2721 and SC2730 in sc27xx-vibra driver
- enhancements for Atmel touchscreens, AD7846 touchscreens, Elan
touchpads, ADP5589, ST1232 touchscreen, TM2 touchkey drivers
- fixes and cleanups to allow clean builds with W=1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: da7280 - fix spelling mistake "sequemce" -> "sequence"
Input: cyapa_gen6 - fix out-of-bounds stack access
Input: sc27xx - add support for sc2730 and sc2721
dt-bindings: input: Add compatible string for SC2721 and SC2730
dt-bindings: input: Convert sc27xx-vibra.txt to json-schema
Input: stmpe - add axis inversion and swapping capability
Input: adp5589-keys - do not explicitly control IRQ for wakeup
Input: adp5589-keys - do not unconditionally configure as wakeup source
Input: ipx4xx-beeper - convert comma to semicolon
Input: parkbd - convert comma to semicolon
Input: new da7280 haptic driver
dt-bindings: input: Add document bindings for DA7280
MAINTAINERS: da7280 updates to the Dialog Semiconductor search terms
Input: elantech - fix protocol errors for some trackpoints in SMBus mode
Input: elan_i2c - add new trackpoint report type 0x5F
Input: elants - document some registers and values
Input: atmel_mxt_ts - simplify the return expression of mxt_send_bootloader_cmd()
Input: imx_keypad - add COMPILE_TEST support
Input: applespi - use new structure for SPI transfer delays
Input: synaptics-rmi4 - use new structure for SPI transfer delays
...
Pull spi updates from Mark Brown:
"The big change this release has been some excellent work from Lukas
Wunner which closes a bunch of holes in the cleanup paths for drivers,
mainly introduced as a result of devm conversions causing bad
interactions with the support SPI has for allocating the bus and
driver data together.
Together with some of the other work done it feels like we've turned
the corner on several long standing pain points with the API.
Summary:
- Many cleanups around probe/remove and error handling from Lukas
Wunner and Uwe Kleine-König, and further fixes around PM from Zhang
Qilong.
- Provide a mask for which bits of the mode can safely be configured
by drivers and use that to fix an issue with the ADS7846 driver.
- Documentation of the expected interactions between SPI and GPIO
level chip select polarity configuration from H. Nikolaus Schaller,
hopefully we're pretty much at the end of sorting out the
interactions there. Thanks to Nikolaus, Sven Van Asbroeck and Linus
Walleij for this.
- DMA support for Allwinner sun6i controllers.
- Support for Canaan K210 Designware implementations and Intel Adler
Lake"
* tag 'spi-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (69 commits)
spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors
spi: Limit the spi device max speed to controller's max speed
spi: spi-geni-qcom: Use the new method of gpio CS control
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
spi: dw: Add support for the Canaan K210 SoC SPI
spi: dw: Add support for 32-bits max xfer size
dt-bindings: spi: dw-apb-ssi: Add Canaan K210 SPI controller
spi: Update DT binding docs to support SiFive FU740 SoC
spi: atmel-quadspi: Fix use-after-free on unbind
spi: npcm-fiu: Disable clock in probe error path
spi: ar934x: Don't leak SPI master in probe error path
spi: mt7621: Don't leak SPI master in probe error path
spi: mt7621: Disable clock in probe error path
media: netup_unidvb: Don't leak SPI master in probe error path
spi: sc18is602: Don't leak SPI master in probe error path
spi: rb4xx: Don't leak SPI master in probe error path
spi: gpio: Don't leak SPI master in probe error path
spi: spi-mtk-nor: Don't leak SPI master in probe error path
spi: mxic: Don't leak SPI master in probe error path
...
gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:
drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
40 | *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
569 | } __packed cmd;
| ^~~
Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.
Fixes: c2c06c41f7 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a fix for cm109 stomping on its own control URB if it tries to toggle
buzzer immediately after userspace opens input device (found by
syzcaller)
- another fix for Raydium touchscreens that do not like splitting
command transfers
- quirks for i8042, soc_button_array, and goodix drivers to make them
work better with certain hardware.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - add upside-down quirk for Teclast X98 Pro tablet
Input: cm109 - do not stomp on control URB
Input: i8042 - add Acer laptops to the i8042 reset list
Input: cros_ec_keyb - send 'scancodes' in addition to key events
Input: soc_button_array - add Lenovo Yoga Tablet2 1051L to the dmi_use_low_level_irq list
Input: raydium_ts_i2c - do not split tx transactions
If device is set up as a wakeup source, I2C core configures the interrupt
line as wake IRQ and PM core automatically configures it for waking up the
system on system suspend transition, so we do not have to explicitly call
enable_irq_wake() and disable_irq_wake() in suspend/resume.
Link: https://lore.kernel.org/r/20201120073920.3214492-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are some version of Elan trackpads that send incorrect data when
in SMbus mode, unless they are switched to use 0x5f reports instead of
standard 0x5e. This patch implements querying device to retrieve chips
identifying data, and switching it, when needed to the alternative
report.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071531.32413-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
