The irq_set_affinity callback should not be set if parent IRQ domain
doesn't present because gpio-tegra driver callback fails in this case,
causing a noisy error messages on system suspend:
Disabling non-boot CPUs ...
IRQ 26: no longer affine to CPU1
IRQ128: set affinity failed(-22).
IRQ130: set affinity failed(-22).
IRQ131: set affinity failed(-22).
IRQ 27: no longer affine to CPU2
IRQ128: set affinity failed(-22).
IRQ130: set affinity failed(-22).
IRQ131: set affinity failed(-22).
IRQ 28: no longer affine to CPU3
IRQ128: set affinity failed(-22).
IRQ130: set affinity failed(-22).
IRQ131: set affinity failed(-22).
Entering suspend state LP1
Hence just don't specify the irq_set_affinity callback if parent PMC
IRQ domain is missing. Tegra isn't capable of setting affinity per GPIO,
affinity could be set only per GPIO bank, thus there is nothing to do
for gpio-tegra in regards to CPU affinity without the parent IRQ domain.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30
Fixes: efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip")
Reported-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Support building driver as a loadable kernel module. This allows to
reduce size of a kernel zImage, which is important for some devices
since size of kernel partition may be limited and since some bootloader
variants have known problems in regards to the initrd placement if kernel
image is too big.
$ lsmod
Module Size Used by
gpio_tegra 16384 27
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Clean up inconsistent whitespaces and tabs in the definition of
tegra_gpio_driver to make code look better a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Use resource-managed variant of debugfs_create_file(0444) to prepare code
for the modularization of the driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Hardware appears to treat zero value as 2^32. Take advantage of this
fact to support on/off values of up to UINT_MAX+1 == 2^32. Adjust both
.apply and .get_state to handle zero as a special case.
Rounded up division result in .get_state can't be zero, since the
dividend is now larger than 0. Remove check for this case.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Analyzed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
gpio-mockup doesn't require SYSFS to be selected so drop that bit from
the Kconfig text.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The description of the flags field of the struct gpio_v2_line_info
mentions "the GPIO lines" while the info only applies to an individual
GPIO line. This was accidentally changed from "the GPIO line" during
formatting improvements.
Reword to "this GPIO line" to clarify and to be consistent with other
struct gpio_v2_line_info fields.
Fixes: 2cc522d393 ("gpio: uapi: kernel-doc formatting improvements")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
gpio-mockup-chardev helper has been obsoleted and removed, so also remove
the tools/gpio code that it, and nothing else, was using.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The GPIO mockup selftests are overly complicated with separate
implementations of the tests for sysfs and cdev uAPI, and with the cdev
implementation being dependent on tools/gpio and libmount.
Rework the test implementation to provide a common test suite with a
simplified pluggable uAPI interface. The cdev implementation utilises
the GPIO uAPI directly to remove the dependence on tools/gpio.
The simplified uAPI interface removes the need for any file system mount
checks in C, and so removes the dependence on libmount.
The rework also fixes the sysfs test implementation which has been broken
since the device created in the multiple gpiochip case was split into
separate devices.
Fixes: 8a39f597bc ("gpio: mockup: rework device probing")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The GPIO bank wake interrupt setting was erroneously removed after
conversion to gpio_irq_chip, thus the wake interrupt programming is
broken now. Secondly, the wake_enb of the GPIO driver should be changed
only after the successful toggling of the IRQ wake-state. Restore the wake
interrupt setting and the programming order.
Fixes: efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Some supported chips (e.g. pca9505) support 40 lines. To be able to give
each line a name the length of the gpio-line-names property must be
allowed to contain up to 40 entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
