The WAN port of the 370-RD has a Marvell PHY, with one LED on
the front panel.y List this LED in the device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document support for LEDs node in phy and add an example for it.
PHY LED will have to match led pattern and should be treated as a
generic led.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Switch LED for each port for MikroTik RB3011UiAS-RM.
MikroTik RB3011UiAS-RM is a 10 port device with 2 qca8337 switch chips
connected.
It was discovered that in the hardware design all 3 Switch LED trace of
the related port is connected to the same LED. This was discovered by
setting to 'always on' the related led in the switch regs and noticing
that all 3 LED for the specific port (for example for port 1) cause the
connected LED for port 1 to turn on. As an extra test we tried enabling
2 different LED for the port resulting in the LED turned off only if
every led in the reg was off.
Aside from this funny and strange hardware implementation, the device
itself have one green LED for each port, resulting in 10 green LED one
for each of the 10 supported port.
Cc: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPQ8064 MikroTik RB3011UiAS-RM DT have currently unevaluted properties
in the 2 switch nodes. The bindings #address-cells and #size-cells are
redundant and cause warning for 'Unevaluated properties are not
allowed'.
Drop these bindings to mute these warning as they should not be there
from the start.
Cc: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs definition example for qca8k Switch Family to describe how they
should be defined for a correct usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document support for LEDs node in ethernet-controller.
Ethernet Controller may support different LEDs that can be configured
for different operation like blinking on traffic event or port link.
Also add some Documentation to describe the difference of these nodes
compared to PHY LEDs, since ethernet-controller LEDs are controllable
by the ethernet controller regs and the possible intergated PHY doesn't
have control on them.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHY can blink the LEDs, simple on/off. All LEDs blink at
the same rate, and the reset default is 84ms per blink, which is
around 12Hz.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be requested to perform hardware accelerated
blinking. Pass this to the PHY driver, if it implements the op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a brightness function, so the LEDs can be controlled from
software using the standard Linux LED infrastructure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be software controlled via the brightness file in /sys.
LED drivers need to implement a brightness_set function which the core
will call. Implement an intermediary in phy_device, which will call
into the phy driver if it implements the necessary function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide stubs for devm_led_classdev_register_ext() and
led_init_default_state_get() so that LED drivers embedded within other
drivers such as PHYs and Ethernet switches still build when LEDS_CLASS
or NEW_LEDS are disabled. This also helps with Kconfig dependencies,
which are somewhat hairy for phylib and mdio and only get worse when
adding a dependency on LED_CLASS.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our use-case needs two AT ports available:
One for running a ppp daemon, and another one for management
This patch enables a second AT port on DATA1
Signed-off-by: Jaime Breva <jbreva@nayarsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
net/mlx5e: Extend XDP multi-buffer capabilities
This series extends the XDP multi-buffer support in the mlx5e driver.
Patchset breakdown:
- Infrastructural changes and preparations.
- Add XDP multi-buffer support for XDP redirect-in.
- Use TX MPWQE (multi-packet WQE) HW feature for non-linear
single-segmented XDP frames.
- Add XDP multi-buffer support for striding RQ.
In Striding RQ, we overcome the lack of headroom and tailroom between
the RQ strides by allocating a side page per packet and using it for the
xdp_buff descriptor. We structure the xdp_buff so that it contains
nothing in the linear part, and the whole packet resides in the
fragments.
Performance highlight:
Packet rate test, 64 bytes, 32 channels, MTU 9000 bytes.
CPU: Intel(R) Xeon(R) Platinum 8380 CPU @ 2.30GHz.
NIC: ConnectX-6 Dx, at 100 Gbps.
+----------+-------------+-------------+---------+
| Test | Legacy RQ | Striding RQ | Speedup |
+----------+-------------+-------------+---------+
| XDP_DROP | 101,615,544 | 117,191,020 | +15% |
+----------+-------------+-------------+---------+
| XDP_TX | 95,608,169 | 117,043,422 | +22% |
+----------+-------------+-------------+---------+
Series generated against net commit:
e61caf04b9 Merge branch 'page_pool-allow-caching-from-safely-localized-napi'
I'm submitting this directly as Saeed is traveling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we add support for multi-buffer XDP handling in Striding RQ, which
is our default out-of-the-box RQ type. Before this series, loading such
an XDP program would fail, until you switch to the legacy RQ (by
unsetting the rx_striding_rq priv-flag).
To overcome the lack of headroom and tailroom between the strides, we
allocate a side page to be used for the descriptor (xdp_buff / skb) and
the linear part. When an XDP program is attached, we structure the
xdp_buff so that it contains no data in the linear part, and the whole
packet resides in the fragments.
In case of XDP_PASS, where an SKB still needs to be created, we copy up
to 256 bytes to its linear part, to match the current behavior, and
satisfy functions that assume finding the packet headers in the SKB
linear part (like eth_type_trans).
Performance testing:
Packet rate test, 64 bytes, 32 channels, MTU 9000 bytes.
CPU: Intel(R) Xeon(R) Platinum 8380 CPU @ 2.30GHz.
NIC: ConnectX-6 Dx, at 100 Gbps.
+----------+-------------+-------------+---------+
| Test | Legacy RQ | Striding RQ | Speedup |
+----------+-------------+-------------+---------+
| XDP_DROP | 101,615,544 | 117,191,020 | +15% |
+----------+-------------+-------------+---------+
| XDP_TX | 95,608,169 | 117,043,422 | +22% |
+----------+-------------+-------------+---------+
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting XDP multi-buffer in striding RQ, use
xdp_buff struct to describe the packet. Make its skb_shared_info collide
the one of the allocated SKB, then add the fragments using the xdp_buff
API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the function more generic. Let it get an additional frame_sz
parameter instead of deriving it from the RQ struct.
No functional change here, just a preparation for a downstream patch.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mlx5e_add_skb_shared_info_frag(), a function dedicated for
adding a fragment into a struct skb_shared_info object.
Use it in the Legacy RQ flow. Similar usage will be added in a
downstream patch by the corresponding Striding RQ flow.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under a few restrictions, TX MPWQE feature can serve multiple TX packets
in a single TX descriptor. It requires each of the packets to have a
single scatter entry / segment.
Today we allow only linear frames to use this feature, although there's
no real problem with non-linear ones where the whole packet reside in
the first fragment.
Expand the XDP TX MPWQE feature support to include such frames. This is
in preparation for the downstream patch, in which we will generate such
non-linear frames.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assumption of non-zero linear length in the XDP xmit
function, used to serve both internal XDP_TX operations as well as
redirected-in requests.
Do not apply the MLX5E_XDP_MIN_INLINE check unless necessary.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function mlx5e_rx_get_linear_stride_sz() returns PAGE_SIZE immediately
in case an XDP program is attached. The more accurate formula is
ALIGN(sz, PAGE_SIZE), to prevent two packets from residing on the same
page.
The assumption behind the current code is that sz <= PAGE_SIZE holds for
all cases with XDP program set.
This is true because it is being called from:
- 3 times from Striding RQ flows, in which XDP is not supported for such
large packets.
- 1 time from Legacy RQ flow, under the condition
mlx5e_rx_is_linear_skb().
No functional change here, just removing the implied assumption in
preparation for supporting XDP multi-buffer in Striding RQ.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mlx5e_xdp_allowed() so it gets the params structure with the
xdp_prog applied, rather than creating a local copy based on the current
params in priv.
This reduces the amount of memory on the stack, and acts on the exact
params instance that's about to be applied.
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
