When handling auto-connected devices, we should execute the rest of the
connection complete when it was previously discovered and it is an ACL
connection.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Bluetooth fails to enter the suspended state correctly, restore the
state to running (re-enabling scans). PM_POST_SUSPEND is only sent to
notifiers that successfully return from PM_PREPARE_SUSPEND notification
so we should recover gracefully if it fails.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johannes Berg says:
====================
Another set of changes:
* HE ranging (fine timing measurement) API support
* hwsim gets virtio support, for use with wmediumd,
to be able to simulate with multiple machines
* eapol-over-nl80211 improvements to exclude preauth
* IBSS reset support, to recover connections from
userspace
* and various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SJA1105 switches R and S have one SerDes port with an 802.3z
quasi-compatible PCS, hardwired on port 4. The other ports are still
MII/RMII/RGMII. The PCS performs rate adaptation to lower link speeds;
the MAC on this port is hardwired at gigabit. Only full duplex is
supported.
The SGMII port can be configured as part of the static config tables, as
well as through a dedicated SPI address region for its pseudo-clause-22
registers. However it looks like the static configuration is not
able to change some out-of-reset values (like the value of MII_BMCR), so
at the end of the day, having code for it is utterly pointless. We are
just going to use the pseudo-C22 interface.
Because the PCS gets reset when the switch resets, we have to add even
more restoration logic to sja1105_static_config_reload, otherwise the
SGMII port breaks after operations such as enabling PTP timestamping
which require a switch reset.
>From PHYLINK perspective, the switch supports *only* SGMII (it doesn't
support 1000Base-X). It also doesn't expose access to the raw config
word for in-band AN in registers MII_ADV/MII_LPA.
It is able to work in the following modes:
- Forced speed
- SGMII in-band AN slave (speed received from PHY)
- SGMII in-band AN master (acting as a PHY)
The latter mode is not supported by this patch. It is even unclear to me
how that would be described. There is some code for it left in the
patch, but 'an_master' is always passed as false.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
net: bridge: vlan options: nest the tunnel options
After a discussion with Roopa about the new tunnel vlan option, she
suggested that we'll be adding more tunnel options and attributes, so
it'd be better to have them all grouped together under one main vlan
entry tunnel attribute instead of making them all main attributes. Since
the tunnel code was added in this net-next cycle and still hasn't been
released we can easily nest the BRIDGE_VLANDB_ENTRY_TUNNEL_ID attribute
in BRIDGE_VLANDB_ENTRY_TUNNEL_INFO and allow for any new tunnel
attributes to be added there. In addition one positive side-effect is
that we can remove the outside vlan info flag which controlled the
operation (setlink/dellink) and move it under a new nested attribute so
user-space can specify it explicitly.
Thus the vlan tunnel format becomes:
[BRIDGE_VLANDB_ENTRY]
[BRIDGE_VLANDB_ENTRY_TUNNEL_INFO]
[BRIDGE_VLANDB_TINFO_ID]
[BRIDGE_VLANDB_TINFO_CMD]
...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a nested tunnel info attribute we can add a separate
one for the tunnel command and require it explicitly from user-space. It
must be one of RTM_SETLINK/DELLINK. Only RTM_SETLINK requires a valid
tunnel id, DELLINK just removes it if it was set before. This allows us
to have all tunnel attributes and control in one place, thus removing
the need for an outside vlan info flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While discussing the new API, Roopa mentioned that we'll be adding more
tunnel attributes and options in the future, so it's better to make it a
nested attribute, since this is still in net-next we can easily change it
and nest the tunnel id attribute under BRIDGE_VLANDB_ENTRY_TUNNEL_INFO.
The new format is:
[BRIDGE_VLANDB_ENTRY]
[BRIDGE_VLANDB_ENTRY_TUNNEL_INFO]
[BRIDGE_VLANDB_TINFO_ID]
Any new tunnel attributes can be nested under
BRIDGE_VLANDB_ENTRY_TUNNEL_INFO.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the drivers are not using channel context, but let the
stack to control/switch channels instead. For such cases, driver
can still remain on channel because the mac80211 stack actually
supports it.
The stack will check if the driver is using chan_ctx and has
ops->remain_on_channel been hooked. Otherwise it will start its
ROC work to remain on channel. So, even if the driver is not
using chan_ctx, the driver is still capable of doing remain on
channel.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Link: https://lore.kernel.org/r/20200312074337.16198-1-yhchuang@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that trigger roaming need to know the lifetime of the configured
PMKSA for deciding whether to trigger the full or PMKSA cache based
authentication. The configured PMKSA is invalid after the PMK lifetime
has expired and must not be used after that and the STA needs to
disassociate if the PMK expires. Hence the STA is expected to refresh
the PMK with a full authentication before this happens (e.g., when
reassociating to a new BSS the next time or by performing EAPOL
reauthentication depending on the AKM) to avoid unnecessary
disconnection.
The PMK reauthentication threshold is the percentage of the PMK lifetime
value and indicates to the driver to trigger a full authentication roam
(without PMKSA caching) after the reauthentication threshold time, but
before the PMK timer has expired. Authentication methods like SAE need
to be able to generate a new PMKSA entry without having to force a
disconnection after this threshold timeout. If no roaming occurs between
the reauthentication threshold time and PMK lifetime expiration,
disassociation is still forced.
The new attributes for providing these values correspond to the dot11
MIB variables dot11RSNAConfigPMKLifetime and
dot11RSNAConfigPMKReauthThreshold.
This type of functionality is already available in cases where user
space component is in control of roaming. This commit extends that same
capability into cases where parts or all of this functionality is
offloaded to the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200312235903.18462-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, userspace is able to detect that a peer silently lost its
state (like, if the peer reboots). wpa_supplicant does this for IBSS-RSN
by registering for auth/deauth frames, but when it detects this, it is
only able to remove the encryption keys of the peer and close its port.
However, the kernel also hold other state about the station, such as BA
sessions, probe response parameters and the like. They also need to be
resetted correctly.
This patch adds the NL80211_EXT_FEATURE_DEL_IBSS_STA feature flag
indicating the driver accepts deleting stations in IBSS mode, which
should send a deauth and reset the state of the station, just like in
mesh point mode.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://lore.kernel.org/r/20200305135754.12094-1-cavallar@lri.fr
[preserve -EINVAL return]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the nl80211 control port is used before this patch, pre-auth frames
(0x88c7) are send to userspace uncoditionally. While this enables userspace
to only use nl80211 on the station side, it is not always useful for APs.
Furthermore, pre-auth frames are ordinary data frames and not related to
the control port. Therefore it should for example be possible for pre-auth
frames to be bridged onto a wired network on AP side without touching
userspace.
For backwards compatibility to code already using pre-auth over nl80211,
this patch adds a feature flag to disable this behavior, while it remains
enabled by default. An additional ext. feature flag is added to detect this
from userspace.
Thanks to Jouni for pointing out, that pre-auth frames should be handled as
ordinary data frames.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-2-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
