Commit cab70040df ("net: igmp:
Reduce Unsolicited report interval to 1s when using IGMPv3") and
2690048c01 ("net: igmp: Allow user-space
configuration of igmp unsolicited report interval") by William Manley made
igmp unsolicited report intervals configurable per interface and corrected
the interval of unsolicited igmpv3 report messages resendings to 1s.
Same needs to be done for IPv6:
MLDv1 (RFC2710 7.10.): 10 seconds
MLDv2 (RFC3810 9.11.): 1 second
Both intervals are configurable via new procfs knobs
mldv1_unsolicited_report_interval and mldv2_unsolicited_report_interval.
(also added .force_mld_version to ipv6_devconf_dflt to bring structs in
line without semantic changes)
v2:
a) Joined documentation update for IPv4 and IPv6 MLD/IGMP
unsolicited_report_interval procfs knobs.
b) incorporate stylistic feedback from William Manley
v3:
a) add new DEVCONF_* values to the end of the enum (thanks to David
Miller)
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: William Manley <william.manley@youview.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On timeout the TCP sender unconditionally resets the estimated degree
of network reordering (tp->reordering). The idea behind this is that
the estimate is too large to trigger fast recovery (e.g., due to a IP
path change).
But for example if the sender only had 2 packets outstanding, then a
timeout doesn't tell much about reordering. A sender that learns about
reordering on big writes and loses packets on small writes will end up
falsely retransmitting again and again, especially when reordering is
more likely on big writes.
Therefore the sender should only suspect that tp->reordering is too
high if it could have gone into fast recovery with the (lower) default
estimate.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of updates intended for 3.12. It is mostly driver
stuff, although Johannes Berg and Simon Wunderlich make a good
showing with mac80211 bits (particularly some work on 5/10 MHz
channel support).
The usual suspects are mostly represented. There are lots of updates
to iwlwifi, ath9k, ath10k, mwifiex, rt2x00, wil6210, as usual.
The bcma bus gets some love this time, as do cw1200, iwl4965, and a
few other bits here and there. I don't think there is much unusual
here, FWIW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version which is present in AM43xx SoC has a minor changes and the
offsets are same as the previous version, so adding new IP version support in
the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pptp driver has lots of byte order warnings from sparse.
This was because the on-the-wire header is in network byte order (obviously)
but the definition did not reflect that.
Also, the address structure to user space actually put the call id
in host order. Rather than break ABI compatibility, just acknowledge
the existing design.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the definition of ax88172a_info matches the declaration seen
by users and silence sparse warnings about symbols without declarations
in the global namespace by moving the declaration into the shared header
asix.h.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that are only referenced from ops structures static, they
do not need to be in the global namespace and sparse complains about this.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
config: make ARCH=m68k allmodconfig
All error/warnings:
drivers/net/wireless/mwifiex/cfg80211.c: In function
'mwifiex_fill_coalesce_rule_info':
>> drivers/net/wireless/mwifiex/cfg80211.c:2493:3: error: implicit
declaration of function 'mwifiex_is_pattern_supported'
[-Werror=implicit-function-declaration]
drivers/net/wireless/mwifiex/cfg80211.c: At top level:
drivers/net/wireless/mwifiex/cfg80211.c:2537:12: warning:
'mwifiex_cfg80211_set_coalesce' defined but not used
[-Wunused-function]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit e370a72363 ("af_unix: improve STREAM behavior with fragmented
memory") added a bug on large send() because the
skb_copy_datagram_from_iovec() call always start from the beginning
of iovec.
We must instead use the @sent variable to properly skip the
already processed part.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
Since there is no public documentation, this driver is mostly the
one published by MOXA that has been heavily cleaned up / ported
from linux 2.6.9.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding paged frags skbs to af_unix sockets introduced a performance
regression on large sends because of additional page allocations, even
if each skb could carry at least 100% more payload than before.
We can instruct sock_alloc_send_pskb() to attempt high order
allocations.
Most of the time, it does a single page allocation instead of 8.
I added an additional parameter to sock_alloc_send_pskb() to
let other users to opt-in for this new feature on followup patches.
Tested:
Before patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 46861.15
After patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 57981.11
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_stream_sendmsg() currently uses order-2 allocations,
and we had numerous reports this can fail.
The __GFP_REPEAT flag present in sock_alloc_send_pskb() is
not helping.
This patch extends the work done in commit eb6a24816b
("af_unix: reduce high order page allocations) for
datagram sockets.
This opens the possibility of zero copy IO (splice() and
friends)
The trick is to not use skb_pull() anymore in recvmsg() path,
and instead add a @consumed field in UNIXCB() to track amount
of already read payload in the skb.
There is a performance regression for large sends
because of extra page allocations that will be addressed
in a follow-up patch, allowing sock_alloc_send_pskb()
to attempt high order page allocations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Encrypt the cookie with both server and client IPv4 addresses,
such that multi-homed server will grant different cookies
based on both the source and destination IPs. No client change
is needed since cookie is opaque to the client.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
callid_sock array is referenced via rcu_dereference and
sparse rcu checks complains about address space mismatch.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa
Yuchung Cheng
David S. Miller
Mugunthan V N
Claudiu Manoil
stephen hemminger
Vlad Yasevich
Mark Brown
John W. Linville
Bing Zhao
Eric Dumazet
Jonas Jensen
Yijing Wang
Sachin Kamat