There is a small problem in handling page bounce.
At the moment blk_max_pfn equals max_pfn, which is in fact not maximum
possible _number_ of a page frame, but the _amount_ of page frames. For
example for the 32bit x86 node with 4Gb RAM, max_pfn = 0x100000, but not
0xFFFF.
request_queue structure has a member q->bounce_pfn and queue needs bounce
pages for the pages _above_ this limit. This routine is handled by
blk_queue_bounce(), where the following check is produced:
if (q->bounce_pfn >= blk_max_pfn)
return;
Assume, that a driver has set q->bounce_pfn to 0xFFFF, but blk_max_pfn
equals 0x10000. In such situation the check above fails and for each bio
we always fall down for iterating over pages tied to the bio.
I want to notice, that for quite a big range of device drivers (ide, md,
...) such problem doesn't happen because they use BLK_BOUNCE_ANY for
bounce_pfn. BLK_BOUNCE_ANY is defined as blk_max_pfn << PAGE_SHIFT, and
then the check above doesn't fail. But for other drivers, which obtain
reuired value from drivers, it fails. For example sata_nv uses
ATA_DMA_MASK or dev->dma_mask.
I propose to use (max_pfn - 1) for blk_max_pfn. And the same for
blk_max_low_pfn. The patch also cleanses some checks related with
bounce_pfn.
Signed-off-by: Vasily Tarasov <vtaras@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: Fix ap_poll_requests counter in lost requests error path.
[S390] zcrypt: Fix possible dead lock in AP bus module.
[S390] cio: Device status validity.
[S390] kprobes: Align probe address.
[S390] Fix TCP/UDP pseudo header checksum computation.
[S390] dasd: Work around gcc bug.
This patch implements set_mac_address for the sungem driver. This
allows changing the mac address of the interface, even when the
interface is up.
Signed-off-by: Ruben Vandeginste <snowbender@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix usb-serial/ftdi build warning
USB: fix usb-serial/generic build warning
USB: another entry for the quirk list
USB: remove duplicated device id in airprime driver
USB: omap_udc: workaround dma_free_coherent() bogosity
UHCI: Fix problem caused by lack of terminating QH
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Fix warning message in PCIE port driver
PCI: Stop unhiding the SMBus on Toshiba laptops
PCI: Fix up PCI power management doc
pci: set pci=bfsort for PowerEdge R900
Change prototypes for __chk_user_ptr and __chk_io_ptr to take const
void* instead of void*, so that code can pass "const void *" to them.
(Right now sparse does not warn about passing const void* to void*
functions, but that is a separate bug that I believe Josh is working on,
and once sparse does check this, the changed prototypes will be
necessary.)
Signed-off-by: Russ Cox <rsc@swtch.com>
Signed-off-by: Josh Triplett <josh@freedesktop.org>
Acked-by: Christopher Li <sparse@chrisli.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul E. McKenney writes:
> Those of use who dive into networking only occasionally would much
> appreciate this. ;-)
No problem here...
Acked-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> (but trivial)
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix annoying build warning:
drivers/usb/serial/ftdi_sio.c:890: warning: enumeration value `FT232RL' not handled in switch
Also add logic to detect FT232R chips (version 6.00, usb 2.0 full speed),
so that case isn't completely useless. (NOTE: FT232RL and FT232RQ are
the same chip in different packages: L is SSOP, Q is QFN.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning when CONFIG_USB_SERIAL_GENERIC is undefined.
drivers/usb/serial/generic.c:24: warning: `generic_probe' declared `static' but never defined
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both airprime and option now want to handle vendor ID 0x1410,
device ID 0x1100. Airprime calls it 'ExpressCard34 Qualcomm 3G CDMA'.
Option calls it 'Novatel Merlin XS620/S640'. Patch attached to remove it
from airprime.
From: Jon K Hellan <jon.kare.hellan@uninett.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to omap_udc, noted with some recent testing:
- Cope with some SMP-induced braindamage in ARM's dma_{alloc,free}_coherent()
implementation: alloc() can be called with IRQs blocked, but since late
last year that's no longer true for free(). This resolves really NASTY
problems with logspamming via WARN_ON(), indicating N-page leaks.
- Be more correct in handling GET_STATUS request for RECIP_ENDPOINT ... the
previous code only handled RECIP_INTERFACE, this version should be correct
except for (sigh) bulk/interrupt endpoints.
- Provide a better name for the function reporting whether the board has
vbus sensing wired up.
GET_STATUS requests for endpoint status still acts strangely though, at least
given one flakey host doesn't always ack the first DATA packet, then the packet
that gets retransmitted doesn't have data!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as871) fixes a problem introduced by an earlier change.
It turns out that some systems really do need to have a terminating
skeleton QH present whenever FSBR is on. I don't know any way to tell
which systems do need it and which don't; the easiest answer is to
have it there always.
This fixes the NumLock-hang bug reported by Jiri Slaby.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: use correct IDE error recovery
pdc202xx_new: Enable ATAPI DMA
ide: cosmetic adaption of drivers/ide/Kconfig concerning SATA
ide: fix locking for manual DMA enable/disable ("hdparm -d")
ide: revert "ide: fix drive side 80c cable check, take 2" for now
PCIE error output should conform to vendor_id:device_id.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was found that the Toshiba laptops with hidden Intel SMBus have SMM
code handling the thermal management which accesses the SMBus. Thus it
is not safe to unhide it and let Linux access it. We have to leave the
SMBus hidden. SMM is a pain, really.
This fixes bugs #6315 and #6395, for good this time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the documentation of PCI power management functions.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch automatically enables pci=bfsort for the Dell PowerEdge
R900. This is necessary to ensure the onboard NICs enumerate in the
proper order, similar to the other systems already on the list.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* d_alloc() in sock_attach_fd() fails leaving ->f_dentry of new file NULL
* bail out to out_fd label, doing fput()/__fput() on new file
* but __fput() assumes valid ->f_dentry and dereferences it
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current sysfs support of clockevents does not obey the "only one
value per file" rule.
The real fix is not 2.6.21 material. Therefor remove the sysfs support
for now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[ bart: the ressurection of 2 years old patch which slipped thru the cracks
(thanks to Sergei Shtylyov for finding it) ]
These is the patch to turn on pdc202xx_new for ATAPI DMA. When testing, it
works fine without the (request_bufflen % 256) workaround as needed in libata.
ide-scsi filters out (pc->request_transfer % 1024) and use PIO, so the pdc202xx
ATAPI DMA problem is avoid. Both ide-cd and ide-scsi won't hit the ATAPI DMA
problem on pdc202xx_new.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since especially Serial ATA has it's own menu point now, I guess we can
change the description of the deprecated SATA driver as well, since the
new libATA subsystem is not configured through a SCSI low-level driver
anymore, but has it's own menu point.
From: Patrick Ringl <patrick_@freenet.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Vasily Tarasov
Linus Torvalds
Ruben Vandeginste
Russ Cox
Robert Olsson
David Brownell
Oliver Neukum
Jon K Hellan
Alan Stern
Prarit Bhargava
Jean Delvare
Jonathan Corbet
Matt Domsch
Alexey Dobriyan
Thomas Gleixner
Suleiman Souhlal
Albert Lee
Patrick Ringl