This op works like .tx_status, except it does not need access to the
skb. This will be used by drivers that cannot match tx status
information to specific packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some variables are assigned unconditionally, remove their
initialisations to help avoid introducing errors later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the regulatory settings change, some channels might become invalid.
Disconnect interfaces acting on these channels, after giving userspace
code a grace period to leave them.
This mode is currently opt-in, and not all interface operating modes are
supported for regulatory-enforcement checks. A wiphy that wishes to use
the new enforcement code must specify an appropriate regulatory flag,
and all its supported interface modes must be supported by the checking
code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
[fix some indentation, typos]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a crash on attempting to calculate the frame duration for a VHT
packet (which needs to be handled by hw/driver instead).
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This option has been marked for deprecation and removal for
a little more than two years, but it's not been very clearly
signalled since it was always possible to just select it.
Make it unselectable now to signal anyone who's still using
it after all this time more clearly. They can still get it
back, but only by patching the kernel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of keeping track of all those special cases where
VLAN interfaces have no bss_conf.chandef, just make sure
they have the same as the AP interface they belong to.
Among others, this fixes a crash getting a VLAN's channel
from userspace since a NULL channel is returned as a good
result (return value 0) for VLANs since the commit below.
Cc: stable@vger.kernel.org [3.18 only]
Fixes: c12bc4885f ("mac80211: return the vif's chandef in ieee80211_cfg_get_channel()")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One of the cases for an invalid channel definition is that
the channel pointer is NULL, in which case the warning is
a bit late since we'll dereference the pointer. Bail out
of the function upon warning about this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Much of the code can be shared by moving it into helper functions
for the CQM event sending.
Also move the code closer together, even in the header file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are no channels allowing 80 MHz to be used, then the
station isn't really VHT capable even if the driver and device
support it in general. In this case, exclude the VHT capability
IE from probe request frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a channel pointer, and we use its center frequency
to look up a channel pointer - which will thus be exactly
the same as the original pointer.
Remove that pointless lookup and just use the pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The supported bandwidth field is a two-bit field, not a bitmap,
so treat it accordingly when disabling 80+80 or 160 MHz.
Note that we can only advertise "80+80 and 160" or "160", not
"80+80" by itself, so disabling 160 also disables 80+80.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit c17aa52c5b.
It was wrong, IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ
already implies that 160 MHz is supported, as it isn't a bitmap
but rather a value in a 2-bit field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A properly set alpha2 value consists of two chars that both contain
letters or digits. If no value is set, both chars keep their initial
value zero. Therefore do not send the alpha2 parameter to user space
if either of the characters has been left at its initial zero value.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the queue mapping earlier, skb->queue_mapping is more likely than
skb->data to still be in d-cache.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let the other listeners being notified when a new or del interface
command has been issued, thus reducing later necessary request to be in
sync with current context.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HWSIM_CMD_GET_RADIO returns information about a specific radio id or
all of them in response to a dump. Create the netlink skb or use the
one provided by the dump functionality. Use the existing attribute
appending function to fill in the same attributes when creating a
new hwsim radio.
Save alpha2 and struct ieee80211_regdomain in the hwsim data or else
they will be lost in the depths of regulatory infrastructure.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out netlink message attribute appending in order to reuse it
with later code. As a result move netlink skb allocation to the
calling function.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace NL80211_ATTR_IFACE_SOCKET_OWNER attribute with more generic
NL80211_ATTR_SOCKET_OWNER that can be used with other commands
that interface creation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The hwname will always be set if idx is negative (as it's
a u32 read into an s64 it can't overflow either) so we can
remove the unnecessary check for hwname being non-NULL.
This was reported by smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Callback add_virtual_intf is supposed to return ERR_PTR and trying to
return NULL results in some "Unable to handle kernel paging request",
etc. As it may be complicated to debug & trace, let's catch it (WARN).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Explicitly initialize the DFS state and beacon found state when handling
channels in the custom regulatory path.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau
Johannes Berg
Arik Nemtsov
Patrik Flykt
Tomasz Bursztyka
Jukka Rissanen
Rafał Miłecki