This patch fixes a bug where devloss is not called on fc_host teardown.
The issue is seen if the LLDD uses rport_rolechg to add the target role
to an rport.
When an rport goes away, the LLDD will call fc_remote_port_delete, which
will start the devloss timer. If the timer expires, the transport will
call the devloss callback and set the FC_RPORT_DEVLOSS_CALLBK_DONE flag.
However, the rport structure is not deleted, it is retained to store the
SCSI id mappings for the rport in case it comes back. In the scenario
where it does come back, and the driver calls fc_remote_port_add, but does
not indicate the "target" role for the rport - the create will clear the
structure, but forgets to clear FC_RPORT_DEVLOSS_CALLBK_DONE flag (which
is cleared if it's added with the target role). The secondary call, of
fc_remote_port_rolechg to add the target role also does not clear the flag.
Thus, the next time the rport goes away, the resulting devloss timer
expiration will not call the driver callback as the flag is still set.
This patch adds the FC_RPORT_DEVLOSS_CALLBK_DONE flags to the list of
those that are cleared upon reuse of the rport structure.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a check-condition in scsi_dh_alua handler for a retry.
Sometimes, I have seen attach failing due to this check-condition with
following error messages on NetApp E series storage.
Dec 7 15:31:01 nilgiris kernel: [102979.696673] scsi 3:0:2:9: alua: port group 00 rel port 01
Dec 7 15:31:01 nilgiris kernel: [102979.697082] scsi 3:0:2:9: alua: rtpg failed with 8000002
Dec 7 15:31:01 nilgiris kernel: [102979.697086] scsi 3:0:2:9: alua: rtpg sense code 06/2a/01
Dec 7 15:31:01 nilgiris kernel: [102979.697088] scsi 3:0:2:9: alua: not attached
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch re-implements LUN Masking feature using SCSI Slave Callouts. With
the new design in the slave_alloc entry point; for each new LUN discovered we
check with our internal LUN Masking config whether to expose or to mask this
particular LUN. We return -ENXIO (No such device or address) from slave_alloc
for the LUNs we don't want to be exposed. We also notify the SCSI mid-layer
to do a sequential LUN scan rather than REPORT_LUNS based scan if LUN masking
is enabled on our HBA port, since a -ENXIO from any LUN in REPORT_LUNS based
scan translates to a scan abort. This patch also handles the dynamic lun
masking config change from enable to disable or vice-versa by resetting
sdev_bflags of LUN 0 appropriately.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch reverts the current LUN Masking Implementation. We re-implemented
this feature using the SCSI Slave Callout's as per the review comments.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Patch fixes the possible NULL pointer dereference when we try to add or delete
a rpwwn to the lunmask config which is not zoned to this port. Check if the
FCS rport is not NULL before de-referencing it.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
skb_linearize already has a check for skb_is_nonlinear,
there is no need to duplicate the check in fcoe.c. This
patch simply removes the unnecessary check and calls
skb_linearize unconditionally.
Reported-by: patrick kelle <patrick.kelle81@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: patrick kelle <patrick.kelle81@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If ql4xdisablesysfsboot = 0 and sendtargets entry as boot index then
driver does export sendtarget entries in sysfs but iscsistart does not
do discovery. So in this case let driver do the discovery and
login to the targets.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A wrong default timeout value programmed in the adapter causes driver
to wait for that much time while waiting for target discoveries to complete.
This could add huge delays during the driver load time. To avoid this,
limit the default timeout value to 12 seconds if the default timeout value
set in adapter is less than 12 seconds and greater than 120 seconds.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In alloc_pdu, libcxgbi tries to allocate a skb with GFP_ATOMIC, which
may potentially fail. When it happens, the current code prints a warning
message.
When the system is under IO stress, this failure may happen lots of
times and it usually scares users.
Instead of printing the warning message, the code now increases the
tx_dropped statistics for the ethernet interface wich is doing the iscsi
task.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sym53c8xx_slave_destroy unconditionally assumes that sym53c8xx_slave_alloc has
succesesfully allocated a sym_lcb. This can lead to a NULL pointer dereference
(exposed by commit 4e6c82b).
Signed-off-by: Stratos Psomadakis <psomas@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
MTD pull for 3.3
* tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6: (113 commits)
mtd: Fix dependency for MTD_DOC200x
mtd: do not use mtd->block_markbad directly
logfs: do not use 'mtd->block_isbad' directly
mtd: introduce mtd_can_have_bb helper
mtd: do not use mtd->suspend and mtd->resume directly
mtd: do not use mtd->lock, unlock and is_locked directly
mtd: do not use mtd->sync directly
mtd: harmonize mtd_writev usage
mtd: do not use mtd->lock_user_prot_reg directly
mtd: mtd->write_user_prot_reg directly
mtd: do not use mtd->read_*_prot_reg directly
mtd: do not use mtd->get_*_prot_info directly
mtd: do not use mtd->read_oob directly
mtd: mtdoops: do not use mtd->panic_write directly
romfs: do not use mtd->get_unmapped_area directly
mtd: do not use mtd->get_unmapped_area directly
mtd: do use mtd->point directly
mtd: introduce mtd_has_oob helper
mtd: mtdcore: export symbols cleanup
mtd: clean-up the default_mtd_writev function
...
Fix up trivial edit/remove conflict in drivers/staging/spectra/lld_mtd.c
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (307 commits)
drm/nouveau/pm: fix build with HWMON off
gma500: silence gcc warnings in mid_get_vbt_data()
drm/ttm: fix condition (and vs or)
drm/radeon: double lock typo in radeon_vm_bo_rmv()
drm/radeon: use after free in radeon_vm_bo_add()
drm/sis|via: don't return stack garbage from free_mem ioctl
drm/radeon/kms: remove pointless CS flags priority struct
drm/radeon/kms: check if vm is supported in VA ioctl
drm: introduce drm_can_sleep and use in intel/radeon drivers. (v2)
radeon: Fix disabling PCI bus mastering on big endian hosts.
ttm: fix agp since ttm tt rework
agp: Fix multi-line warning message whitespace
drm/ttm/dma: Fix accounting error when calling ttm_mem_global_free_page and don't try to free freed pages.
drm/ttm/dma: Only call set_pages_array_wb when the page is not in WB pool.
drm/radeon/kms: sync across multiple rings when doing bo moves v3
drm/radeon/kms: Add support for multi-ring sync in CS ioctl (v2)
drm/radeon: GPU virtual memory support v22
drm: make DRM_UNLOCKED ioctls with their own mutex
drm: no need to hold global mutex for static data
drm/radeon/benchmark: common modes sweep ignores 640x480@32
...
Fix up trivial conflicts in radeon/evergreen.c and vmwgfx/vmwgfx_kms.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
hid-input/battery: add FEATURE quirk
hid-input/battery: remove battery_val
hid-input/battery: power-supply type really *is* a battery
hid-input/battery: make the battery setup common for INPUTs and FEATUREs
hid-input/battery: deal with both FEATURE and INPUT report batteries
hid-input/battery: add quirks for battery
hid-input/battery: remove apparently redundant kmalloc
hid-input: add support for HID devices reporting Battery Strength
HID: hid-multitouch: add support 9 new Xiroku devices
HID: multitouch: add support for 3M 32"
HID: multitouch: add support of Atmel multitouch panels
HID: usbhid: defer LED setting to a workqueue
HID: usbhid: hid-core: submit queued urbs before suspend
HID: usbhid: remove LED_ON
HID: emsff: use symbolic name instead of hardcoded PID constant
HID: Enable HID_QUIRK_MULTI_INPUT for Trio Linker Plus II
HID: Kconfig: fix syntax
HID: introduce proper dependency of HID_BATTERY on POWER_SUPPLY
HID: multitouch: support PixArt optical touch screen
HID: make parser more verbose about parsing errors by default
...
Fix up rename/delete conflict in drivers/hid/hid-hyperv.c (removed in
staging, moved in this branch) and similarly for the rules for same file
in drivers/staging/hv/{Kconfig,Makefile}.
SCSI updates for post 3.2 merge window
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (67 commits)
[SCSI] lpfc 8.3.28: Update driver version to 8.3.28
[SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters
[SCSI] lpfc 8.3.28: Critical Miscellaneous fixes
[SCSI] Lpfc 8.3.28: FC and SCSI Discovery Fixes
[SCSI] lpfc 8.3.28: Add support for ABTS failure handling
[SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support
[SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces
[SCSI] mpt2sas: Removed redundant calling of _scsih_probe_devices() from _scsih_probe
[SCSI] mac_scsi: Remove obsolete IRQ_FLG_* users
[SCSI] qla4xxx: Update driver version to 5.02.00-k10
[SCSI] qla4xxx: check for FW alive before calling chip_reset
[SCSI] qla4xxx: Fix qla4xxx_dump_buffer to dump buffer correctly
[SCSI] qla4xxx: Fix the IDC locking mechanism
[SCSI] qla4xxx: Wait for disable_acb before doing set_acb
[SCSI] qla4xxx: Don't recover adapter if device state is FAILED
[SCSI] qla4xxx: fix call trace on rmmod with ql4xdontresethba=1
[SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set
[SCSI] qla4xxx: Perform context resets in case of context failures.
[SCSI] iscsi class: export pid of process that created
[SCSI] mpt2sas: Remove unused duplicate diag_buffer_enable param
...
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: omap_wdt.c: fix the WDIOC_GETBOOTSTATUS ioctl if not implemented.
watchdog: new driver for VIA chipsets
watchdog: ath79_wdt: flush register writes
drivers/watchdog/lantiq_wdt.c: drop iounmap for devm_ allocated data
watchdog: documentation: describe nowayout in coversion-guide
watchdog: documentation: update index file
watchdog: Convert wm831x driver to devm_kzalloc()
watchdog: add nowayout helpers to Watchdog Timer Driver Kernel API
watchdog: convert drivers/watchdog/* to use module_platform_driver()
watchdog: Use DEFINE_SPINLOCK() for static spinlocks
watchdog: Convert Wolfson drivers to module_platform_driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
regulator: max8925: fix enabled/disabled judgement mistake
regulator: add regulator_bulk_force_disable function
regulator: pass regulator_register of_node in fixed voltage driver
regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
regulator: Enable supply regulator if child rail is enabled.
regulator: mc13892: Convert to devm_kzalloc()
regulator: mc13783: Convert to devm_kzalloc()
regulator: Fix checking return value of create_regulator
regulator: Fix the error handling if create_regulator fails
regulator: Export regulator_is_supported_voltage()
regulator: mc13892: add device tree probe support
regulator: mc13892: remove the unnecessary prefix from regulator name
regulator: Convert wm831x regulator drivers to devm_kzalloc()
regulator: da9052: Staticize non-exported symbols
regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
regulator: Update da9052-regulator for DT changes
regulator: DA9052/53 Regulator support
regulator: pass device_node to of_get_regulator_init_data()
regulator: If a single voltage is set with device tree then set apply_uV
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (31 commits)
pinctrl: remove unnecessary max pin number
pinctrl: correct a offset while enumerating pins
pinctrl: some typo fixes
pinctrl: rename U300 and SIRF pin controllers
pinctrl: pass name instead of device to pin_config_*
pinctrl: add "struct seq_file;" to pinconf.h
pinctrl: conjure names for unnamed pins
pinctrl: add a group-specific hog macro
pinctrl: don't create a device for each pin controller
arm/u300: don't use PINMUX_MAP_PRIMARY*
pinctrl: implement PINMUX_MAP_SYS_HOG
pinctrl: add a pin config interface
pinctrl/coh901: driver to request its pins
pinctrl: u300-pinmux: register proper GPIO ranges
pinctrl: move the U300 GPIO driver to pinctrl
ARM: u300: localize GPIO assignments
pinctrl: make it possible to add multiple maps
pinctrl: make a copy of pinmux map
pinctrl: GPIO direction support for muxing
pinctrl: print pin range in GPIO range debugs
...
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
ahci: support the STA2X11 I/O Hub
pata_bf54x: fix BMIDE status register emulation
ata: add ata port hibernate callbacks
ata: update ata port's runtime status during system resume
[SCSI] runtime resume parent for child's system-resume
ahci: platform support for suspend/resume
libata-core: kill duplicate statement in ata_do_set_mode()
pata_of_platform: remove direct dependency on OF_IRQ
SATA/PATA: convert drivers/ata/* to use module_platform_driver()
pata_cs5536: forward port changes from cs5536
libata-sff: use ATAPI_{COD|IO}
ata: add ata port runtime PM callbacks
ata: add ata port system PM callbacks
[SCSI] sd: check runtime PM status in sd_shutdown
[SCSI] check runtime PM status in system PM
[SCSI] add flag to skip the runtime PM calls on the host
ata: make ata port as parent device of scsi host
ahci: start engine only during soft/hard resets
Alok Kataria
James Smart
Moger, Babu
Krishna Gudipati
Robert Love
Vikas Chaudhary
Manish Rangankar
Nilesh Javali
Lalit Chandivade
Thadeu Lima de Souza Cascardo
Stratos Psomadakis
Richard Weinberger
Linus Torvalds