Also, sort the properties alphabetically and make indentation
consistent. Wording largely taken from i2c-rk3x.txt, thanks guys!
Only "i2c-scl-internal-delay-ns" is new, the rest is used by two drivers
already and was documented in their driver binding documentation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the I2C adapter devices of_node to that of the PCI device, such that
I2C clients may be instantiated via device tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For platform with auto restart support, between every transfer,
i2c controller will trigger an interrupt and SW need to handle
it to start new transfer. When doing write-then-read transfer,
instead of restart mechanism, using WRRD mode to have controller
send both transfer in one request to reduce latency.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The suspended flag is a flag holding the device's PM status.
The runtime framework does that for us.
Use pm_runtime_suspended call instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the clocks are enabled at probe and disabled at remove.
Which keeps the clocks enabled even if no transaction is going on.
This patch enables the clocks at the start of transfer and disables
after it.
Also adapts to runtime pm.
converts dev pm to const to silence a checkpatch warning.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds a i2c_check_quirks helper function to check the quirk flags
of an i2c adapter, in a similar way to i2c_check_functionality.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported in the links given below. the BCM2835 has a hardware bug in
its i2c module which prevents a correct clock stretching. This patch
adds the I2C_AQ_NO_CLK_STRETCH quirk flag to i2c-bcm2835.
Signed-off-by: Nicola Corna <nicola@corna.info>
[wsa: put the links into the code as comments]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C_AQ_NO_CLK_STRETCH to drivers/i2c/algos/i2c-algo-bit.c when getscl
is not available.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C_AQ_NO_CLK_STRETCH quirk flag, to be used when clock stretching is
not supported.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All protected sections are only called from sleep-able context, so there is
no need to use a spinlock.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for port names for the SB800 chipset.
Since the chipset supports a multiplexed main SMBus controller, adding
the channel name to the adapter name is necessary to differentiate the
ports better (for example in sensors output).
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. The multiplexed ports share the same SMBus address and
register set. The port is selected by bits 2:1 of the smb_en register
(0x2C).
Only one port can be active at any point in time therefore a mutex is
needed in order to synchronize access.
Additionally, the commit avoids requesting and releasing the SMBus base
address index region on every multiplexed transfer by moving the
request_region call into piix4_probe.
Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
support to access sensor data from the w83795adg).
Cc: Thomas Brandon <tbrandonau@gmail.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. Therefore the static variable piix4_main_adapter is
converted into a piix4_main_adapters array that can hold one
i2c_adapter for each multiplexed port.
The auxiliary adapter remains unchanged since it represents the second
(not multiplexed) SMBus controller on the SB800 chipset.
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang
Niklas Söderlund
Paul Burton
Ludovic Desroches
Wolfram Sang
Liguo Zhang
Shubhrajyoti Datta
Nicola Corna
Lars-Peter Clausen
LABBE Corentin
Christian Fetzer