Kill the remaining shift macro in favor of calculating at compile time
its value from the more descriptive mask, which gives us a better
representation of the register layout.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: Global 2 cosmetics
Similarly to what has been done for the Port and Global 1 registers,
this patch series prefixes and documents the macros of Global 2.
It brings no functional changes except for 1/10 which fixes the IRL init
for 88E6390 family.
Changes in v2: make *_g2_irl_init_all static inline without
NET_DSA_MV88E6XXX_GLOBAL2 and compile test with and without the symbol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6352 family has a Global 2 register dedicated to the
watchdog setup. But the 88E6390 turned it into an indirect table.
Prefix and document that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Trunk registers macros. At the same
time, fix the hask -> hash typo and use the mv88e6xxx_port_mask helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.
The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.
Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)
Finally do not use complex macros but simple 16-bit mask to document the
registers organization.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.
This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.
This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.
A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Icenowy Zheng says:
====================
net-next: stmmac: dwmac-sun8i: add support for V3s
Allwinner V3s features an EMAC like the on in H3, but without external MII
interfaces, so being not able really to use RMII/RGMII.
And it has a different default value of syscon (0x38000 instead of 0x58000
on H3), which shows a problem that the EMAC clock freq should be 24MHz.
(Both H3 and V3s SoCs doesn't have extra xtal input for EPHY, and the
main xtal is 24MHz. The default value of H3 is set to 24MHz, but the V3s
default value is set to 25MHz).
First two patches are device tree binding patches, the third forces
the frequency to 24MHz and the fourth really add the V3s support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s SoC has an Ethernet MAC and an internal PHY like the ones
in H3 SoC, however the MAC has no external *MII interfaces available at
GPIOs, thus only MII connection to internal PHY is supported.
Add this variant of EMAC to dwmac-sun8i driver.
The default value of the syscon EMAC-related register seems to have
changed from H3, but it seems to be a harmless change.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY control part of the EMAC syscon register has a bit called
CLK_SEL. On the datasheet it says that if it's 0 the EPHY clock is 25MHz
and if it's 1 the clock is 24MHz.
However, according to the datasheets, no Allwinner SoC with EPHY has any
extra xtal input pins for the EPHY, and the system xtal is 24MHz.
That means the EPHY is not possible to get a 25MHz xtal input, and thus
the frequency can only be 24MHz.
It doesn't matter on H3 as the default value of H3 is 24MHz, however on
V3s the default value is wrongly set to 25MHz, which prevented the EPHY
from working properly.
Force the EPHY clock frequency to 24MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s SoC has a syscon like the one in H3.
Add its compatible string.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s SoC has a Ethernet MAC like the one in Allwinner H3, but
have no external MII capability. That means that it can only use the
EPHY and cannot do Gbps transmission.
Add binding for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates says:
====================
net: Introduction of the tc tests
Apologies for sending this as one big patch. I've been sitting on this a little
too long, but it's ready and I wanted to get it out.
There are a limited number of tests to start - I plan to add more on a regular
basis.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the beginnings of a testsuite for tc functionality in the kernel.
These are a series of unit tests that use the tc executable and verify
the success of those commands by checking both the exit codes and the
output from tc's 'show' operation.
To run the tests:
# cd tools/testing/selftests/tc-testing
# sudo ./tdc.py
You can specify the tc executable to use with the -p argument on the command
line or editing the 'TC' variable in tdc_config.py. Refer to the README for
full details on how to run.
The initial complement of test cases are limited mostly to tc actions. Test
cases are most welcome; see the creating-testcases subdirectory for help
in creating them.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed*: RDMA and infrastructure for iWARP
This series focuses on RDMA in general with emphasis on required changes
toward adding iWARP support. The vast majority of the changes introduced
are in qed/qede, with a couple of small changes to qedr
[mentioned below].
The infrastructure changes:
- Patch #1 adds the ability to pass PBL memory externally for a newly
created chain.
- Patches #4, #5 rename qede_roce.[ch] into qede_rdma.[ch] + change
prefixes from _roce_ to _rdma_, as the API between qede and qedr is
agnostic to the variant of the RDMA protocol used. These patches also
touch qedr [basically to align it with the renaming, nothing more].
- Patch #7 replaces the current SPQ async mechanism into serving
registered callbacks [before adding iWARP which would add another client
in need of this sort of functionallity].
The non-infrastrucutre changes:
- Patches #2, #3 contain DCB-related changes to better align RDMA with
configured DCB.
- Patch #6 contains a minor [mostly theoretical fix] to release flow.
Changes from previous versions
------------------------------
- V4: This is actually a repost of V3 due to some confusion regarding
the sent cover-letter
- V3: Add commit log message in #4 indicating change in header inclusion
- V2: Add several inclusion into qede_rdma.h to have proper declarations
of all variable types used in it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever firmware indicates that there's an async indication it needs
to handle, there's a switch-case where the right functionality is called
based on function's personality and information.
Before iWARP is added [as yet another client], switch over the SPQ into
a callback-registered mechanism, allowing registration of the relevant
event-processing logic based on the function's personality. This allows
us to tidy the code by removing protocol-specifics from a common file.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we have iWARP support, the qede portion of the qedr<->qede would
serve all the RDMA protocols - so rename the file to be appropriate
to its function.
While we're at it, we're also moving a couple of inclusions to it into
.h files and adding includes to make sure it contains all type
definitions it requires.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCBx update occurs while QPs are open, stop sending edpms until all
QPs are closed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot
David S. Miller
Icenowy Zheng
Lucas Bates
Michal Kalderon
Mintz, Yuval