"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Reported-by: Cesare Leonardi <celeonar@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFCSR is only used in rt2800. For other chipsets, the debug struct
for rfcsr should be zeroed, which isn't be an issue, since the code
can now cope with that.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow a register to be unspecified, therefore not creating its debugfs
file entry.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a mesh peer indicates it is operating as 20MHz-only in its HT
operation IE, have the rate control algorithm respect this by disabling
the equivalent bit in the ieee80211_sta HT capabilities.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need the station rate info when inserting a new sta_info. The
patch "mac80211: refactor mesh peer initialization" wrongly assumed the
rate info could be applied after insertion. After further review, this
is clearly not the case.
This fixes a regression where HT parameters were not applied before
inserting the sta_info, causing performance degradation.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"oui_type" in structure "ieee_types_vendor_header" is not used separately,
so include it in "oui" array. Now complete oui will be compared fixing
following warnings.
drivers/net/wireless/mwifiex/sta_ioctl.c:1410 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/sta_ioctl.c:1435 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1177 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1185 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate control updation never be called on 2040 BSS change.
The station should update its rate control on receiving beacon
with different HT mode in the HT operation IE. Not doing so,
leads to sending frames with higher(ht40) rates whereas AP is
operating in lower mode (ht20).
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a cut and paste mistake, sizeof(struct mib_local) was intended
instead of sizeof(struct mib_phy). The call to at76_get_mib() uses
sizeof(struct mib_local) correctly, although I changed that to
sizeof(*m) for style reasons after discussion with some of the wireless
maintainers.
The current code works fine because mib_phy structs are larger than
mib_local structs. But we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are various problems happened on 5GHz band not observed on
2.4 GHz (microcode errors, queue stuck, etc... ) . Also roaming
between 5GHz AP and 2GHz does not work very well. To workaround
the problems add option to disable 5GHz support. This will help
on environments where APs are dual-band, and devices will not try
to associate on band where issues happen.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Also remove a debug print when allocation error occurred.
The kernel will complain anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When bluetooth coex is active and certain condition matched,
driver need to decide should the tx power been reduce or not.
Adding the logic to manage it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Ben Greear
Wey-Yi Guy
Meenakshi Venkataraman
Ben Hutchings
Anisse Astier
Stanislav Yakovlev
Thomas Pedersen
Amitkumar Karwar
Rajkumar Manoharan
WarheadsSE
Dan Carpenter
Emmanuel Grumbach
Stanislaw Gruszka