This patch removes the phytec specific setting of the bus width
and switches to the more generic query_bus_param/set_bus_param
hooks
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the phytec specific setting of the bus width
and switches to the more generic query_bus_param/set_bus_param
hooks
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some Phytec cameras have a I2C GPIO expander which allows it to
switch between different sensor bus widths. This was previously
handled in the camera driver. Since handling of this switch
varies on several boards the cameras are used on, the board
support seems a better place to handle the switch
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Camera sensors have a native bus width say support, but on some
boards not all sensor data lines are connected to the image
interface and thus support a different bus width than the sensors
native one. Some boards even have a bus driver which dynamically
switches between different bus widths with a GPIO.
This patch adds a hook which board code can use to support different
bus widths.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure videobuf_waiton() is used before freeing a buffer.
Without this fix we may return the buffer to the allocator
before the bus mastering operation is finished.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera doesn't set up any image format without an explicit
S_FMT. According to the API this should be supported, for example,
capture-example.c from v4l2-apps by default doesn't issue an S_FMT. This
patch moves negotiating of available host-camera format translations to
probe() time, and restores the state from the last close() on the next
open(). This is needed for some drivers, which power down or reset
hardware after the last user closes the interface. This patch also has a
nice side-effect of avoiding multiple allocation anf freeing of format
translation tables.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the case, that we have to capture with a default format, i.e., when the
user doesn't call S_FMT, we have to use the field value according to the
default, configured at open() time.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera doesn't set up any image format without an explicit S_FMT.
It seems this should be supported, since, for example, capture-example.c from
v4l2-apps by default doesn't issue an S_FMT. This patch configures a default
image format on open().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As host and camera drivers become more complex, differences between S_FMT and
S_CROP functionality grow, this patch separates them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bt819 needs the parent driver to drive a GPIO pin low and high in order to
reset its fifo. Use the new notify callback for this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a notify callback to v4l2_device to let sub-devices notify their
parent of special events.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Normally the parent device of v4l2_device is used as the video device
node's parent. But if it was not set, then use the parent field in the
video_device struct.
This is needed in the cx88 driver, which has one core v4l2_device but
creates multiple pci devices (one each for raw and mpeg video).
So you cannot associate the core v4l2_device with a particular PCI device,
but you can do that for each video_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new support for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI board broke the
existing boards. Interrupts for the netup part were enabled and handled
without testing whether the current board actually had a netup -> instant
and fatal crash.
I've added tests to do this only for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI
board.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug where all frame headers were being discarded, instead of being part of the
stream output, on MR97310A cameras.
The frame headers contain information which may be useful in processing
the video output and therefore should be kept and not discarded.
A corresponding patch to the decompression algorithm in
libv4lconvert/mr97310a.c corrects the change in frame offset.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setting state->frontend.demodulator_priv to NULL in the event of
a kzalloc error will result in an OOPS. Just remove that line.
Thanks to Matthias Schwarzott for pointing this out.
Cc: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the i2c sub-device cannot be found, then we must unregister the i2c_client.
Otherwise this will prevent a possible probe for a different device on that same
address.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Emphasize the need to call i2c_set_adapdata and clarify the use of the
chipid in v4l2_i2c_new_(probed_)device().
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll start off with MODULE_VERSION("0.1")
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
small whitespace cleanup - space missing after the *
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sascha Hauer
Magnus Damm
Kuninori Morimoto
Guennadi Liakhovetski
Hans Verkuil
Theodore Kilgore
Michael Krufky
Mauro Carvalho Chehab