Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the multimedia clock controller found on MSM
8960 based platforms. This should allow multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM8960
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Reset controllers and clock controllers are combined into one IP
block on Qualcomm chipsets. Usually a reset signal is associated
with each clock branch but sometimes a reset signal is associated
with a handful of clocks. Either way the register interface is
the same; set a bit to assert a reset and clear a bit to deassert
a reset. Add support for these types of resets signals.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for the root clock generators on Qualcomm devices.
RCGs are highly customizable mux/divider/counter clocks that can
be used to generate almost any rate desired given some input
source that is faster than the desired rate.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for Qualcomm's PLLs (phase locked loops). This is
sufficient enough to be able to determine the rate the PLL is
running at. We can add rate setting support later when it's
needed.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a clock type that associates a regmap pointer and some
enable/disable bits with a clk_hw struct. This will be the struct
that a hw specific implementation wraps if it wants to use the
regmap helper functions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some of Qualcomm's clocks can change their parent and rate at the
same time with a single register write. Add support for this
hardware to the common clock framework by adding a new
set_rate_and_parent() op. When the clock framework determines
that both the parent and the rate are going to change during
clk_set_rate() it will call the .set_rate_and_parent() op if
available and fall back to calling .set_parent() followed by
.set_rate() otherwise.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If a user of <linux/reset-controller.h> doesn't include
<linux/of.h> before including reset-controller.h they'll get a
warning as follows:
include/linux/reset-controller.h:44:17:
warning: 'struct of_phandle_args' declared inside parameter list
This is because of_phandle_args is not forward declared. Add the
declaration to silence this warning.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
sirfprima2 and sirfatlas6 are two different SoCs in CSR SiRF series. for
prima2 and atlas6, there are many shared clocks but there are still
some different register layout and hardware clocks, then result in
different clock table.
here we re-arch the driver to
1. clk-common.c provides common clocks for prima2 and atlas6,
2. clk-prima2.h describles registers of prima2 and clk-prima2.c provides
prima2 specific clocks and clock table.
3. clk-atlas6.h describles registers of atlas6 and clk-atlas6.c provides
atlas6 specific clocks and clock table.
4. clk.h and clk.c expose external interfaces and provide uniform entry
for both prima2 and atlas6.
so both prima2 and atlas6 will get support by drivers/clk/sirf.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The composite clock's .determine_rate implementation can call the
underyling .determine_rate callback corresponding to rate_hw or the
underlying .determine_rate callback corresponding to mux_hw. In both
cases we pass in rate_hw, which is wrong. Fixed by passing mux_hw into
the correct callback.
Reported-by: Lemon Dai <dailemon.gl@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clks member of the clk_onecell_data structure should
point to a valid clk array (no NULL entries allowed),
and the clk_num should be equal to the number
of elements in the clks array.
The MSTP driver fails to satisfy the above conditions.
The clks array may contain NULL entries if not all
clock-indices are initialized in the device tree.
Thus, if the clock indices are interleaved we end up
with NULL pointers in-between.
The other problem is the driver uses maximum clock index
as the number of clocks, which is incorrect (less than
the actual number of clocks by 1).
Fix the first issue by pre-setting the whole clks array
with ERR_PTR(-ENOENT) pointers instead of zeros; and
use maximum clkidx + 1 as the number of clocks to fix
the other one.
This should make of_clk_src_onecell_get() return the following:
* valid clk pointers for all clocks registered;
* ERR_PTR(-EINVAL) if (idx >= clk_data->clk_num);
* ERR_PTR(-ENOENT) if the clock at the selected index was not
initialized in the device tree (and was not registered).
Changes in V2:
* removed brackets from the one-line for loop
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use clkidx when registering MSTP clocks instead of loop counter
since the value is then used to access the specific clock index bit
in the mstp register.
The issue was introduced by the following commit:
f94859c215 "clk: shmobile: Add MSTP clock support"
Changes in V2:
* none
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a label and #clock-cells property to device node of
max77686 PMIC to allow using it as a clock provider.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If max77686 chip is instantiated from device tree, it is desirable to
have an OF clock provider to allow device tree based look-up of clocks.
This patch adds OF clock provider registration to the clk-max77686
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As a prerequisite for further patch adding OF clock provider support to
the driver, this patch changes the driver to store an array of struct
clk * as driver data.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch fixes invalid kfree() and adds missing call to clk_unregister()
in error and remove paths in max77686_clk_probe(). While at it, error
handling is also cleaned up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As a preparation for further patches, this patch modifies the clock
registration helper function to return a pointer to the newly registered
clock. No functional change is done to the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The function can simply return 0, without jumping to a separate label,
which does exactly the same. This patch does not introduce any
functional change, just a clean-up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is usually nice to know frequency of a clock, so this patch adds a
.recalc_rate() callback returning rates of provided clocks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Changing status of clock gates in max77686 requires i2c transfers, which
can sleep, so this is done in prepare and unprepare callbacks. Due to
this, checking whether whether the clock is ungated must be done
in is_prepared() callback as well, for consistency.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Stephen Boyd
Barry Song
Mike Turquette
Valentine Barshak
Tomasz Figa