- If a termios change fails due to lack of memory we should copy the
old settings back over as the device has not changed
- Note various locking problems
- kl5kusb105 had various remaining tty flag handling problems
- Make safe_serial use tty_insert_flip_string not open coded loops
- set termios speed properly in usb_serial
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1079) cleans up the way URB_* flags are exported in
usbfs.
The URB_NO_INTERRUPT flag is now exported (this is the
only behavioral change).
USBDEVFS_URB_* macros are added for URB_NO_FSBR,
URB_ZERO_PACKET, and URB_NO_INTERRUPT, making explicit the
fact that the kernel accepts them.
The flag matching takes into account that the URB_* values
may change as the kernel evolves, whereas the USBDEVFS_URB_*
values must remain fixed since they are a user API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1072) fixes some recently-introduced compile problems
that show up in ehci-hcd when CONFIG_PM is turned off.
PORT_WAKE_BITS needs to be defined always.
ehci_port_power() is called during initialization by all the
EHCI variants other than the PCI version, in which it is
"defined but not used". So add a call to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simplify processing of completed qtds, and correct handling of short
reads, by removing two state variables:
- "qtd_status" wasn't needed. The current URB's status is either
OK (-EINPROGRESS) or some fault status. Once a fault appears,
the queue halts and any later QTDs are immediately removed, so
no temporary status is needed. (Or for typical short reads,
it's not treated as a fault, so no queue halt is needed.)
- "do_status" was erroneous. Because of how the queue is set up,
short control reads can (and should!) be treated like full size
reads, and cleaned up the usual way. The status stage will be
executed transparently, and usbcore handles the choice of whether
to report this status as unexected.
The "do_status" problem caused a rather perplexing timing-dependent
problem with usbtest case 10. Sometimes it would make the controller
skip a dozen transactions while (wrongly) trying to clean up after a
short transfer. Fortunately, removing a dcache contention issue made
this become trivial to reproduce (on one test rig), so enough clues
finally presented themselves ... I think this has been around for a
very long time, but was worsened by recent urb->status changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix bogus assignment of "unsigned char *" to "char *": preserve
unsignedness. These values are used directly as descriptor lengths
when iterating through the buffer, so this *could* cause oddness
that potentially includes oopsing. (IMO not likely, except as
part of a malicious device...)
Fix the bogus warning in CDC ACM which highlighted this problem
(by showing a negative descriptor type). It uses the undesirable
legacy err() for something that's not even an error; switch to
use dev_dbg, and show descriptor types in hex notation to match
the convention for such codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1068b) disables the RD interrupt flag when an OHCI root
hub is suspended with remote wakeup disabled. Although the spec
clearly states that this flag permits the controller to issue an
interrupt when a resume request from downstream is detected and not
when a local status change occurs, some controllers mistakenly use it
for both types of event.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting. The setting
is then saved in the do_remote_wakeup flag.
Later on, however, the device_may_wakeup() value can change because of
user activity. So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup(). This patch (as1076)
makes that change for root hubs in several places.
The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.
And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1061) makes g_file_storage more compliant with the
Bulk-Only Transport specification. After an invalid CBW is received,
the gadget must ignore any further bulk-OUT data until it is reset.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unused check for num_interrupt and friends as well as remove
them from the header file because no usb-serial drivers no longer
reference them.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-serial core no longer checks these fields so remove them from
all of the individual drivers. They will be removed from the usb-serial
core in a patch later in the series.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting DTR et al. should work for all interfaces
if you actually pass the interface number. :-P
This should help with devices that have important pseudo-serial ports
that aren't on the first interface in the device.
Signed-off-by: Chris Collins <chris@ursys.com.au>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds documentation about the new usb anchor infrastructure.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide better comments about qh_completions() and QTD handling.
That code can be *VERY* confusing, since it's evolved over a few
years to cope with both hardware races and silicon quirks.
Remove two unlikely() annotations that match the GCC defaults
(and are thus pointless); add an "else" to highlight code flow.
This patch doesn't change driver behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1077) logs an error message whenever the kernel is
unable to enumerate a new USB device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Comments here are so outdated that they are plain wrong. We cannot expect
people to write correct drivers if the headers have incorrect comments.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given that most of drivers/usb/serial/Kconfig is wrapped inside:
if USB_SERIAL
...
endif # USB_SERIAL
remove the consequently redundant dependencies on USB_SERIAL.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the ability to trigger asynchronous unlinks of anchored URBs. This
is needed for error handling in the comntext of completion handlers, which
cannot sleep.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can
support SH7366 USB host by changing several R8A66597 code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the problem that enumeration of a USB device was slow.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver ignored the value of bInterval and revised the problem
that performed interrupt transfer.
ASIX USB Ethernet adapter comes to work with this host controller
by applying this patch.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes unimplemented TCFLSH handling from oti6858, because it was
preventing TCFLSH handling by upper layer (line discipline) drivers (see
drivers/char/tty_io.c line 3450).
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ming Lei
Alan Cox
Harvey Harrison
Alan Stern
David Brownell
Oliver Neukum
Greg Kroah-Hartman
Chris Collins
Robert P. J. Day
Yoshihiro Shimoda
Paulius Zaleckas