Using __test_and_{set,clear}_bit_le() with ignoring its return value
can be replaced with __{set,clear}_bit_le().
This also removes unnecessary casts.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove 'discards_supported' from the dm_table structure. The same
information can be easily discovered from the table's target(s) in
dm_table_supports_discards().
Before this fix dm_table_supports_discards() would skip checking the
individual targets' 'discards_supported' flag if any one target in the
table didn't set num_discard_requests > 0. Now the per-target
'discards_supported' flag is effective at insuring the final DM device
advertises discard support. But, to be clear, targets that don't
support discards (!num_discard_requests) will not receive discard
requests.
Also DMWARN if a target sets 'discards_supported' override but forgets
to set 'num_discard_requests'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
For normal kernel pages, CPU cache is synchronized by the dma layer.
However, this is not done for pages allocated with vmalloc. If we do I/O
to/from vmallocated pages, we must synchronize CPU cache explicitly.
Prior to doing I/O on vmallocated page we must call
flush_kernel_vmap_range to flush dirty cache on the virtual address.
After finished read we must call invalidate_kernel_vmap_range to
invalidate cache on the virtual address, so that accesses to the virtual
address return newly read data and not stale data from CPU cache.
This patch fixes metadata corruption on dm-snapshots on PA-RISC and
possibly other architectures with caches indexed by virtual address.
Cc: stable <stable@kernel.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Avoid dereferencing a NULL pointer if the number of feature arguments
supplied is fewer than indicated.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
This patch makes dm-snapshot flush disk cache when writing metadata for
merging snapshot.
Without cache flushing the disk may reorder metadata write and other
data writes and there is a possibility of data corruption in case of
power fault.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
ALSA: hda - Fix duplicated DAC assignments for Realtek
ALSA: asihpi - off by one in asihpi_hpi_ioctl()
ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
ALSA: asihpi - bug fix pa use before init.
ALSA: hda - Add support for vref-out based mute LED control on IDT codecs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (54 commits)
tpm_nsc: Fix bug when loading multiple TPM drivers
tpm: Move tpm_tis_reenable_interrupts out of CONFIG_PNP block
tpm: Fix compilation warning when CONFIG_PNP is not defined
TOMOYO: Update kernel-doc.
tpm: Fix a typo
tpm_tis: Probing function for Intel iTPM bug
tpm_tis: Fix the probing for interrupts
tpm_tis: Delay ACPI S3 suspend while the TPM is busy
tpm_tis: Re-enable interrupts upon (S3) resume
tpm: Fix display of data in pubek sysfs entry
tpm_tis: Add timeouts sysfs entry
tpm: Adjust interface timeouts if they are too small
tpm: Use interface timeouts returned from the TPM
tpm_tis: Introduce durations sysfs entry
tpm: Adjust the durations if they are too small
tpm: Use durations returned from TPM
TOMOYO: Enable conditional ACL.
TOMOYO: Allow using argv[]/envp[] of execve() as conditions.
TOMOYO: Allow using executable's realpath and symlink's target as conditions.
TOMOYO: Allow using owner/group etc. of file objects as conditions.
...
Fix up trivial conflict in security/tomoyo/realpath.c
Currently when we get a read error during recovery, we simply abort
the recovery.
Instead, repeat the read in page-sized blocks.
On successful reads, write to the target.
On read errors, record a bad block on the destination,
and only if that fails do we abort the recovery.
As we now retry reads we need to know where we read from. This was in
bi_sector but that can be changed during a read attempt.
So store the correct from_addr and to_addr in the r10_bio for later
access.
Signed-off-by: NeilBrown<neilb@suse.de>
If a read error is detected during recovery the code currently
fails the read device.
This isn't really necessary. recovery_request_write will signal
a write error to end_sync_write and it will record a write
error on the destination device which will record a bad block
there or kick it from the array.
So just remove this call to do md_error.
Signed-off-by: NeilBrown <neilb@suse.de>
If we get a write error during resync/recovery don't fail the device
but instead record a bad block. If that fails we can then fail the
device.
Signed-off-by: NeilBrown <neilb@suse.de>
We already attempt to fix read errors found during normal IO
and a 'repair' process.
It is best to try to repair them at any time they are found,
so move a test so that during sync and check a read error will
be corrected by over-writing with good data.
If both (all) devices have known bad blocks in the sync section we
won't try to fix even though the bad blocks might not overlap. That
should be considered later.
Also if we hit a read error during recovery we don't try to fix it.
It would only be possible to fix if there were at least three copies
of data, which is not very common with RAID10. But it should still
be considered later.
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a write error (in the data area, not in metadata),
update the badblock log rather than failing the whole device.
As the write may well be many blocks, we trying writing each
block individually and only log the ones which fail.
Signed-off-by: NeilBrown <neilb@suse.de>
If we succeed in writing to a block that was recorded as
being bad, we clear the bad-block record.
This requires some delayed handling as the bad-block-list update has
to happen in process-context.
Signed-off-by: NeilBrown <neilb@suse.de>
Writing to known bad blocks on drives that have seen a write error
is asking for trouble. So try to avoid these blocks.
Signed-off-by: NeilBrown <neilb@suse.de>
When recovering one or more devices, if all the good devices have
bad blocks we should record a bad block on the device being rebuilt.
If this fails, we need to abort the recovery.
To ensure we don't think that we aborted later than we actually did,
we need to move the check for MD_RECOVERY_INTR earlier in md_do_sync,
in particular before mddev->curr_resync is updated.
Signed-off-by: NeilBrown <neilb@suse.de>
During resync/recovery limit the size of the request to avoid
reading into a bad block that does not start at-or-before the current
read address.
Similarly if there is a bad block at this address, don't allow the
current request to extend beyond the end of that bad block.
Now that we don't ever read from known bad blocks, it is safe to allow
devices with those blocks into the array.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to repair a read error, don't read from
devices with a known bad block.
As we are only reading PAGE_SIZE blocks, we don't try to
narrow down to smaller regions in the hope that only part of this
page is bad - it isn't worth the effort.
Signed-off-by: NeilBrown <neilb@suse.de>
When redirecting a read error to a different device, we must
again avoid bad blocks and possibly split the request.
Spin_lock typo fixed thanks to Dan Carpenter <error27@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch just covers the basic read path:
1/ read_balance needs to check for badblocks, and return not only
the chosen slot, but also how many good blocks are available
there.
2/ read submission must be ready to issue multiple reads to
different devices as different bad blocks on different devices
could mean that a single large read cannot be served by any one
device, but can still be served by the array.
This requires keeping count of the number of outstanding requests
per bio. This count is stored in 'bi_phys_segments'
On read error we currently just fail the request if another target
cannot handle the whole request. Next patch refines that a bit.
Signed-off-by: NeilBrown <neilb@suse.de>
When a loop ends with a large if, it can be neater to change the
if to invert the condition and just 'continue'.
Then the body of the if can be indented to a lower level.
Signed-off-by: NeilBrown <neilb@suse.de>
Akinobu Mita
Mike Snitzer
Alasdair G Kergon
Mikulas Patocka
Linus Torvalds
NeilBrown