Add new ->probe_reset operation to ata_port_operations obsoleting
->phy_reset. The main difference from ->phy_reset is that the new
operation is not allowed to manipulate libata internals directly.
It's not allowed to configure or disable the port or devices. It can
only succeed or fail and classify attached devices into passed
@classes.
This change gives more control to higher level and eases sharing reset
methods with EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make ata_dev_try_classify take @r_err to store tf error register value
on completion and return device class instead of directly manipulating
dev->class. This is preparation for new reset mechanism.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Export ata_busy_sleep(), to be used by low level driver reset functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add constants needed to perform SRST. This is preparation for adding
softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_eh_qc_complete/retry() using scsi_eh_finish_cmd() and
scsi_eh_flush_done_q(). This removes all eh scsicmd finish hacks from
low level drivers.
This change was first suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Export two SCSI EH command handling functions. To be used by libata EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Return AC_ERR_* mask from issue fuctions instead of 0/-1. This
enables things like failing a qc with AC_ERR_HSM when the device
doesn't set DRDY when the qc is about to be issued.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add detailed AC_ERR_* flags and use them. Long-term goal is to
describe all errors with err_mask and tf combination (tf for failed
sector information, etc...). After proper error diagnosis is
implemented, sense data should also be generated from err_mask instead
of directly from hardware tf registers as it is currently.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In ahci_host_intr err_mask is determined from IRQ status but never
used. This patch sets qc->err_mask to the determined err_mask.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When ata_qc_issue() fails, the qc might have been dma mapped or not.
So, performing only ata_qc_free() results in dma map leak. This patch
makes ata_qc_issue() mark dma map flags correctly on failure and calls
ata_qc_complete() after ata_qc_issue() fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
qc used to be freed automatically on command completion. However, as
a qc can carry information about its completion status, it can be
useful to its owner/issuer after command completion. This patch makes
freeing qc responsibility of its owner. This simplifies
ata_exec_internal() and makes command turn-around for atapi request
sensing less hackish.
This change was originally suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
All ata_qc_free() does is calling __ata_qc_complete() which isn't used
anywhere else. Fold __ata_qc_complete() into ata_qc_free().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Unlike their older siblings, ICH6 and 7 use different scheme for MAP
VALUE. This patch makes ata_piix interpret MV properly on ICH6/7.
Pre-ICH6/7
The value of these bits indicate the address range the SATA port
responds to, and whether or not the SATA and IDE functions are
combined.
000 = Non-combined. P0 is primary master. P1 is secondary master.
001 = Non-combined. P0 is secondary master. P1 is primary master.
100 = Combined. P0 is primary master. P1 is primary slave. P-ATA is
2:0 Map Value secondary.
101 = Combined. P0 is primary slave. P1 is primary master. P-ATA is
secondary.
110 = Combined. P-ATA is primary. P0 is secondary master. P1 is
secondary slave.
111 = Combined. P-ATA is primary. P0 is secondary slave. P1 is
secondary master.
ICH6/7
Map Value - R/W. Map Value (MV): The value in the bits below indicate
the address range the SATA ports responds to, and whether or not the
PATA and SATA functions are combined. When in combined mode, the AHCI
memory space is not available and AHCI may not be used.
00 = Non-combined. P0 is primary master, P2 is the primary slave. P1
is secondary master, P3 is the 1:0 secondary slave (desktop
only). P0 is primary master, P2 is the primary slave (mobile
only).
01 = Combined. IDE is primary. P1 is secondary master, P3 is the
secondary slave. (desktop only)
10 = Combined. P0 is primary master. P2 is primary slave. IDE is secondary
11 = Reserved
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, without this patch, ata_piix misdetects my ICH7's combined mode,
ending up not applying bridge limits to PX-710SA and configuring IDE
drive on 40-c cable to UDMA/66.
Thanks.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The compat layer timeout handling changes in:
9f72949f67
are busted. This is most easily seen with an X application
that uses sub-second select/poll timeout such as emacs. You
hit a key and it takes a second or so before the app responds.
The two ROUND_UP() calls upon entry are using {tv,ts}_sec where it
should instead be using {tv_usec,ts_nsec}, which perfectly explains
the observed incorrect behavior.
Another bug shot down with git bisect.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an unnecessary softlockup watchdog warning in the ia64
uncached_build_memmap() that occurs occasionally at 256p and always at
512p. The problem occurs at boot time.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Migrate perfmon from using an old semaphore to a completion handler.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tejun Heo
Jeff Garzik
David S. Miller
Linus Torvalds
David S. Miller
John Hawkes
Jes Sorensen