The KERNCZ is new AMD SB/FCH generation name, like HUDSON2.
0x790b is the device ID for this generation.
Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove module of dw_mmc driver will hung for eMMC devices if we follow the
steps which are listed below,
insmod dw_mmc.ko
insmod dw_mmc-pci.ko
rmmod dw_mmc-pci.ko
The root cause for this issue is, dw_mci_remove() will disable all the
interrupts by programming 0x0 to INTMASK register then it will call
dw_mci_cleanup_slot(). But dw_mci_cleanup_slot() is issuing CMD6 to
disable the eMMC boot partition and it is waiting for Command Complete
interrupt. Since INTMASK was already cleared by dw_mci_remove(), Command
Complete interrupt is not reaching the system. This leads to process hung.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 3a48edc4bd ("mmc: sdhci: Use mmc core regulator infrastucture")
changed the behavior for how to assign the ocr_avail mask for the mmc
host. More precisely it started to mask the bits instead of assigning
them.
Restore the behavior, but also make it clear that an OCR mask created
from an external regulator overrides the other ones. The OCR mask is
determined by one of the following with this priority:
1. Supported ranges of external regulator if one supplies VDD
2. Host OCR mask if set by the driver (based on DT properties)
3. The capabilities reported by the controller itself
Fixes: 3a48edc4bd ("mmc: sdhci: Use mmc core regulator infrastucture")
Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
MMC_PM_KEEP_POWER doesn't imply MMC_PM_WAKE_SDIO_IRQ, we should only
enable device wake up when MMC_PM_WAKE_SDIO_IRQ is set. And "pm_flags"
is the requested pm features, we should not set it in the host driver.
At the same time, device wakeup is disabled by default, so there's no
need to disable device wakeup explicitly.
This patch fixes the warning as following:
[ 64.616651] ------------[ cut here ]------------
[ 64.616665] WARNING: CPU: 0 PID: 79 at linux/kernel/irq/manage.c:603 irq_set_irq_wake+0xf0/0x11c()
[ 64.616667] Unbalanced IRQ 87 wake disable
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Other subsystem buses attach PM domains during probe, but prior calling
the driver's ->probe() method. During the removal phase, detaching the PM
domain will be done after invoking the driver's ->remove() callback.
Convert the SDIO bus to follow this behavior and add error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the ->reset() callback is implemented for SD, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the ->reset() callback is implemented for MMC, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We're currently using a fixed frequency clock specified in the DT, so
enabling is a no-op. However, the RPi firmware-based clocks driver
can actually disable unused clocks, so when switching to use it we
ended up losing our MMC clock once all devices were probed.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable interrupt mode to detect card instead of polling mode
for P1020/P4080/P5020/P5040/T1040 by removing the quirk
SDHCI_QUIRK_BROKEN_CARD_DETECTION. This could improve data
transferring performance and avoid the call trace caused by
polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The iMX6Q/DL can not support HS200 mode while iMX6SL and iMX6SX can,
so introduce a new flag to distinguish them.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The imx6sx usdhc is derived from imx6sl, the difference is minor.
imx6sx have the errata ESDHC_FLAG_ERR004536 fixed.
So introduce a new compatible string for imx6sx to distinguish them.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using specific compatible string in binding doc to make the binding
more clear.
It's also used to avoid checkpatch warning in the future like follows:
WARNING: DT compatible string "fsl,imx6sx-usdhc" appears un-documented --
check ./Documentation/devicetree/bindings/
+ { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
total: 0 errors, 1 warnings, 18 lines checked
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The uSDHC has an ADMA Length Mismatch errata ERR004536 which may
cause ADMA work abnormally. The errata has already been fixed for
i.MX6Q TO1.2 and i.MX6DL TO1.1 by enable the bit 7 in 0x6c register.
Unfortunately this fix is not included in i.MX6SL.
So we disable ADMA for i.MX6SL and use SDMA instead.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usdhc does not have missing card interrupt issue, so don't execute
workaround for usdhc.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In esdhc_writel_le() function, there's duplicated checking of the same
register as follows:
"if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))".
Merge them into one and remove the duplicated one.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable detection of HS400 support via capability bit-63
for some Intel host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the select_drive_strength callback to provide
drive strength selection for Intel SPT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.
Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make a new function out of common code used for drive
strength selection.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vincent Wan
Fabian Frederick
Prabu Thangamuthu
Ulf Hansson
Jisheng Zhang
Eric Anholt
Yangbo Lu
Dong Aisheng
Dong Aisheng
Adrian Hunter