This patch continues the effort which began with:
"[PATCH] p54pci: move tx cleanup into tasklet".
Thanks to these changes, p54pci's interrupt & tx
cleanup routines can be made lock-less.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The loop that passes non-data frames to all relevant vifs inside the
__ieee80211_rx_handle_packet keeps a pointer to the previous sdata to
avoid having to make unnecessary copies of the frame it's handling.
This led to a bug that caused it to apply the ieee80211_rx_data state
to the wrong interface, thereby either missing the rx.sta pointer or
having it assigned where it shouldn't be.
This breaks (among other things) aggregation on some vifs, as action
frame exchages are dropped to the cooked monitor interface due to
rx->sta being NULL.
Fix this by restructuring the loop so that it prepares the rx data just
before making the skb copy and calling the rx handlers.
Cc: stable@kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As all bt packets are priority traffic during bt scan, wifi
will get disconnected when bt scan lasts for few seconds. Fix
this by allocating 10% of bt period time (4.5ms) to wifi fully.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon sent gating doesn't seem to work with any combination
of flags. Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.
Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time. This fixes the following error in AP mode:
ath5k phy0: no further txbuf available, dropping packet
Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_hdrlen() should account account new HT Control field in 802.11
data frame header introduced by IEEE 802.11n standard.
According to 802.11n-2009 HT Control field is present in data frames
when both of following are met:
1. It is QoS data frame.
2. Order bit is set in Frame Control field.
The change might be totally compatible with legacy non-11n aware frames,
because 802.11-2007 standard states that "all QoS STAs set this subfield
to 0".
Signed-off-by: Andriy V. Tkachuk <andrit@ukr.net>
Acked-by : Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a device has multiple MAC addresses, userspace will
need to know about that. Similarly, if it allows the
MAC addresses to vary by a bitmask.
If a driver exports multiple addresses, it is assumed
that it will be able to deal with that many different
addresses, which need not necessarily match the ones
programmed into the device; if a mask is set then the
device should deal addresses within that mask based
on an arbitrary "base address".
To test it all and show how it is used, add support
to hwsim even though it can't actually deal with
addresses different from the default.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a TKIP key is updated, we should pass the station
pointer instead of just the address, since drivers can
use that to store their own data. We also need to pass
the virtual interface pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: move control.hw_key assignment" changed an if-else into two
separate if statments, but the if-else is needed to prevent
dereferencing a null info->control.hw_key. This fixes avoids a lock-up
during association on my machine when using WEP.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users wishing to tweak tx power want it to happen immediately,
try to respect that. This was tested by Lorenzo by measuring the
received signal strength from an AP with ath9k and the patch.
Changing the tx power on the AP produced these results:
1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm
2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm
3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm
4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm
5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm
The result with 0 is an anomoly and would need to be
addressed through a separate patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nl80211_associate() was rejecting (re)association attempts with EBUSY
in some cases where we are currently associated with an AP that uses
different channel from the destination AP. Fix this by passing the
current wdev to rdev_fixed_channel() in the same way that was already
done for join-IBSS and connect commands. This allows the fixedchan
check to skipped for the current wdev and allows the reassociation to
proceed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the v10 firmware running on 8688 HW, clearing WPA keys after setting the
WEP key prevents us from being able to associate with WEP APs.
Swapping the calling order for assoc_helper_wpa_keys() and
assoc_helper_wep_keys fixes that issue.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the tx cleanup routines out of the critical
interrupt context and into the (previously known as rx) tasklet.
The main goal of this operation is to remove the extensive
usage of spin_lock_irqsaves in the generic p54common library.
The next step would be to modify p54usb to do the
rx processing inside a tasklet (just like usbnet).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>