Considering following scenario - the touch is present on the screen
at the beginning of the last conversion sequence, but by the time
the last sequence is finished, the finger is lift off. The AD7879 data
available interrupt signals (DAV) completion, however some X,Y values
are not valid because the screen inputs were floating during the
acquisition.
The AD7877 acts differently here, since it only asserts DAV if the
touch is still present when the conversion sequence finished.
Based on the fact that this can only happen in the last sample of the
repeated conversion sequence, we simply skip the last (short glitches
are filtered by the AD7879 internal median and average filters).
This doesn't cause noticeable side effects, since the minimum conversion
interval is 9.44ms. We receive ~100 waypoint samples per second, so we
simply delay the result by 9.44ms.
We also reject samples where pressure is greater than pressure_max.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cintiq, being a display tablet, doesn't have mouse and associated BTN_s.
Make sure we do not specify them when registering Cintiq's input device
so that userland can retrieve the exact tool set the device supports.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
KBUILD_MODNAME normalizes "-" to "_". This is non-obvious and results in
the id name for ADP5588 being "adp5588_keys" while the other supported id
is "adp5587-keys". So avoid this define and use an explicit string as the
id name.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of using asynchronous SPI API and then spinning waiting for SPI
transfer to complete when disabling the device, let's use threaded IRQ
model and spi_sync().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of manually creating one set of attributes or another set up
is_visible method in attribute group structure to control whether
aux3 or gpio3 attribute is presented to userspace.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
PS2Mult is a simple serial protocol used for multiplexing several PS/2
streams into one serial data stream. It's used e.g. on TQM85xx series
of boards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to always call usb_autopm_put_interface() in wacom_open(),
not only when initialization fails, otherwise the device will be
marked as PM-busy and will never be put in suspended state.
Based on patch by Oliver Neukum.
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Suppress events where pressure > pressure_max.
These events come typically along with inaccurate X and Y samples.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some input users such as Android or X require BTN_TOUCH events.
Implement EV_KEY:BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to the AD7877 datasheet:
Each transfer operation is 16-bit. If multiple read/write operations are
to be performed, CS must be taken high after the end of each read/write
operation before another read/write operation can be performed by
taking CS low again.
Make sure CS toggles after each transfer in the message.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make hp680_ts_init/exit() call cancel_delayed_work_sync() instead of
calling cancel_delayed_work() followed by flush_scheduled_work().
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When annotating mutex to avoid false lockdep reports we should not
be using MOUSEDEV_MIX as lock subclass but rather SINGLE_DEPTH_NESTING.
Signed-off-by: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 9114337 introduces regulator operations in ads7846 touchscreen
driver. Among these operations, some are called while holding a
spinlock. On many platforms regulators reside on slow buses, such as
I2C/SPI and require sleep while accessing them.
The touchscreen itself is also a SPI device and currently relies on
asynchronous SPI access to avoid sleeping in interrupt context. Let's
switch to using threaded IRQ to be able to access SPI bus
synchronously (which simplifies driver a bit); it also allows safe
access to the regulators as well.
This has been tested on the ti_omap3530evm board:
1) using ts_lib after normal boot
2) using ts_lib after "#echo 1/0 > /sys/bus/spi/devices/spi0.1/disable"
3) using ts_lib after "#echo mem > /sys/power/state" and "wake up"
Also tested on pandora.
Based on original patch by Dmitry Torokhov.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some (rare) serio devices need to have multiple serio children. One of
the examples is PS/2 multiplexer present on several TQC STKxxx boards,
which connect PS/2 keyboard and mouse to single tty port.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Program keyboard controller to generate a wake-up request on events and
on long key presses. It will not generate wake-up requests on timeouts
since driver code does not handle them.
This allows keyboard to wake-up OMAP from suspend.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove SYSCONFIG register configuration, omap hwmod framework will
use internal API to modify as required.
Other minor updates:
- Change a variable name from DEF to VAL, this represents a value
- Break line width to 80 characters
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Get mem and irq resources using platform helpers
- platform_get_base
- platform_get_irq
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Michael Hennerich
Dmitry Torokhov
Ping Cheng
Nicolas Kaiser
Dmitry Eremin-Solenikov
Daniel Mack
Tejun Heo
Hitoshi Mitake
Jason Wang
Naveen Kumar Gaddipati
Mike Turquette
Abraham Arce