The port specific options are currently unused resulting in an
empty OVS_VPORT_ATTR_OPTIONS nested attribute being inserted
into every OVS_VPORT_CMD_GET message.
Don't insert OVS_VPORT_ATTR_OPTIONS if no options are present.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
It contains the public netlink interface bits required by userspace to
make use of the interface.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Kills the FLOW_BUFSIZE constant which needs to be calculated manually
and replaces it with key_attr_size() based on nla_total_size().
Calculates the size of datapath messages instead of relying on
NLMSG_DEFAULT_SIZE and moves the existing message size calculations
into own functions for clarity.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Less error prone as it takes into account the length of both the
destination buffer and the source attribute and documents when
data is copied from an attribute.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Specifying the minimal length in the policy makes it reuseable
and documents the interface.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
o VFs might get scheduled out after sending a command to a PF
and scheduled in after receiving a response. Implement a
worker thread to handle atomic commands.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for commands from VF to PF.
o PF validates the commands sent by the VF before sending
it to adapter.
o vPort is a container of resources. PF creates vPort
for VFs and attach resources to it. vPort is
transparent to the VF.
o Separate 83xx TX and RX hardware resource cleanup from 82xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter provides communication channel between VF and PF.
Any control commands from the VF driver are sent to the PF driver
through this communication channel. PF driver validates the
commands before sending them to the adapter. Similarly PF driver
forwards any control command responses to the VF driver
through this communication channel. Adapter sends message pending
event to VF or PF when there is an outstanding response or a command
for VF or PF respectively. When a command or a response is sent over
a channel VF or PF cannot send another command or a response
until adapter sends a channel free event. Adapter allocates 1K area to
VF and PF each for this communication.
o Commands and responses are encapsulated in a header. Header determines
sequence id, number of fragments, fragment number etc.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o VF will use shared MSI-X interrupt vector for Tx and Rx.
o When QLCNIC_INTR_SHARED flag is set Tx and Rx will
share MSI-X interrupt vector. Tx will use a separate
MSI-X interrupt vector from Rx otherwise.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add QLCNIC_SRIOV to Kconfig.
o Provide PCI sysfs hooks to enable and disable SR-IOV.
o Allow enabling only when CONFIG_QLCNIC_SRIOV is defined.
o qlcnic_sriov_pf.c has all the PF related SR-IOV
functionality.
o qlcnic_sriov_common.c has VF functionality and SR-IOV
functionality which is common between VF and PF.
o qlcnic_sriov.h is a common header file for SR-IOV defines.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_ARCH_IXDP2X01 and CONFIG_MACH_IXDP2351 Kconfig macros are
unused since the ixp23xx and ixp2000 platforms were removed in v3.5. So
remove the last code still depending on these macros. And since
CS89x0_NONISA_IRQ was only set if either of these two macros was defined
we can also remove that macro and the code depending on it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d0418bb712 (net: sh_eth: Add eth support
for R8A7779 device) was a failed attempt to add support for one of members of
the R-Car SoC family. That's for three reasons: it treated R8A7779 the same
as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask
in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in
R-Car Ether), and it didn't add a new register offset array despite the closest
SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether
registers have, and also some of the registers in this old mapping don't exist
on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not
adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724
related section to its pristine state...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver's header file contains initialized register offset tables which (as
any data definitions), of course, have no business being there. Move them to
the driver's body, somewhat beautifying the initializers, while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtnl_fdb_dump() when the fdb_dump ndo op is not populated
we never set the idx value so that cb->arg[0] is always 0.
Resulting in a endless loop of messages.
Introduced with this commit,
commit 090096bf3d
Author: Vlad Yasevich <vyasevic@redhat.com>
Date: Wed Mar 6 15:39:42 2013 +0000
net: generic fdb support for drivers without ndo_fdb_<op>
CC: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben pointed out following patch fixes bug in checking device
name length limits while forming tunnel device name.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace per_cpu with per_cpu_ptr to save conversion between address and pointer
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9419121330 replaced the macros
NLMSG_NEXT with calls to nlmsg_next which produces this warning:
kernel/audit.c: In function ‘audit_receive_skb’:
kernel/audit.c:928:3: warning: passing argument 2 of ‘nlmsg_next’ makes pointer from integer without a cast
In file included from include/net/rtnetlink.h:5:0,
from include/net/neighbour.h:28,
from include/net/dst.h:17,
from include/net/sock.h:68,
from kernel/audit.c:55:
include/net/netlink.h:359:1: note: expected ‘int *’ but argument is of type ‘int’
Fix this by sending the intended pointer.
Signed-off-by: Alexandru Copot <alex.mihai.c@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Zhou
Thomas Graf
Rajesh Borundia
Paul Bolle
Sergei Shtylyov
John Fastabend
Pravin B Shelar
Li RongQing
Hong zhi guo
Alexandru Copot
Steffen Trumtrar