This patch finishes cx88-blackbird conversion to use video_ioctl2. Video
standards are generated automatically inside videodev.c. the big ioctl
parser is removed, using, instead, video_ioctl2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l2_tvnorm were meant to describe video standards and its names to V4L2 API.
However, this were doing by some static structures at the driver.
This patch changes the internals in a way that, at the driver, only a
v4l2_tvnorm (a 64 bit integer) should be filled, with all supported
tvnorms. videodev will dynamically generate the proper API array
based on supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_ioctl2 handler provides V4L2 API parsing.
Using it makes the driver simpler, and isolates API parsing.
This allows future reusage of driver controls using other ways, like sysfs
and/or procfs and increases isolation of driver-specific handling from the
generic common ioctl processing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the previous patch, mplayer started but was polling the video
device forever without any video actually coming out. Further analysis
showed that it does a VIDIOC_S_FMT with width and height set to -1 (!!!).
The code handling this only cares that both are lower than the minimum
range allowed so it ends up setting the size to 19x17 (!!) This pretty
much breaks the encoder here. Even if this breakage is yet another (TM)
result of my setup, setting the size to 19x17 by default would surprise
most users IMHO.
So, special case for -1 and interpret this to be a request for the
default size, please. Users can then set their favorite size both
through mplayer and through sysfs.
With this patch, mplayer finally works in pvr:// mode (not that we
really gain anything over operating it through sysfs with lirc,
sometime I might actually get off my lazy a** and contribute this
setup too)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This should allow mplayer pvr:// to start. The trick is that no matter
what actual input we use under this "fake" one, it will be able to do
stereo :-)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Audio mode changes are not private to the audio chip - other I2C
modules need to see this as well. And since the command in question
is VIDIOC_S_TUNER which is a standard v4l2 command, we really should
be broadcasting it out. This change sets up a broadcast pathway for
VIDIOC_S_TUNER and also eliminates the now redundant code from the
audio chip handler.
This fix enables stereo reception for the FM radio
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Attempts to enumerate or operate on a group of EXT_CTRLS where the
group size is zero is OK; don't fail on such operations. At least one
application uses this to probe for the existence of this API so let it
succeed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This bug caused uninitalized data to be returned during a G_TUNER status poll.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The lack of a break statement in the handling of VIDIOC_S_TUNER caused
errors to result. Fixed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than hardcoding frequency ranges everywhere, rely on
VIDIOC_G_TUNER results wherever we can.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab
Pantelis Koukousoulas
Mike Isely
Ahmed S. Darwish