My queue management rework broke drivers that don't
have multiple AC queues and register a single queue
only, causing a warning:
WARNING: at net/mac80211/iface.c:162 ieee80211_check_queues
This was due to filling the queues wrongly and then
noticing the error when checking later.
Reported-and-Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds a missing read to flush the previous write (per the Broadcom SDK).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify ioremap_nocache calls to reflect the number of bytes read/written.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI Memory Resource start address and size are variable, dependent on
the H/W configuration. Modify the computation of io_map_base to use the
computed values.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first thing bcm47xx_fill_sprom does is initialize (zero fill) the SPROM. For
BCMA SOC, this wipes out any values previously read by bcm47xx_fill_sprom_ethernet
(see arch/mips/bcm47xx/setup.c - bcm47xx_get_sprom_bcma). Move the initialization
of SPROM so it is called prior to filling in any values.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_device_name only provides names for Broadcom cores. Modify logic to
provide names for MIPS and ARM cores as well.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If brcmsmac is used on non PCI(s) devices it should not try to access
bus->host_pci.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The irq number is copied from the PCIe host device to the bcma cores so
just request it using the bcma core device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no code doing anything useful in nicpci.c anymore, so remove
it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ai_chipcontrl_epa4331 is not referenced by any method in brcmsmac and
the functionality is already in bcma_chipco_bcm4331_ext_pa_lines_ctl in
drivers/bcma/driver_chipcommon_pmu.c
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is now done by bcma_core_pci_config_fixup() in drivers/bcma/driver_pci.c
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The devices I know of are not using a PCIe core with rev <= 10. The
BCM4718 uses a PCIe core with revision 14 and the BCM43224 uses a PCIe
core with revision 15. This patch removes support for old PCIe core
versions, which are not found on devices supported by brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are no devices which are using bcma and have a PCI bus, just a
PCIe bus or something else. bcma does not support PCI devices, so lets
also remove PCI support from brcmsmac. All devices currently supported
by brcmsmac are PCIe based.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lowest chip common version used on bcma based devices is 31 on the
bcm4718 and 32 on the bcm4313, bcm43224, and bcm43225, so the support
for the old versions could be removed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma now provide this data and brcmsmac should get it from there and
not parse it by its self.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac now takes the sprom from bcma and do not uses its own sprom
parsing any more. Remove this code as it is not used any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg
Nathan Hintz
Hauke Mehrtens