For the Marvel 88e1111 PHY only two SGMII modes are available, both
allowing only SGMII to copper mode (with or without clock). SGMII
to fiber mode is not supported. Make sure the fiber/copper registers
selector bits are cleared for selecting copper mode.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Couple of fixes/adjustments
Ido Schimmel (5):
mlxsw: Call free_netdev when removing port
mlxsw: Make system port to local port mapping explicit
mlxsw: Simplify mlxsw_sx_port_xmit function
mlxsw: Use correct skb length when dumping payload
mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit
Jiri Pirko (2):
mlxsw: Make pci module dependent on HAS_DMA and HAS_IOMEM
mlxsw: Strip FCS from incoming packets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use the length of the transmitted skb (which was freed), but
that of the response skb.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.
Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves compile errors on um-allyesconfig.
Note that there are many other drivers which have the same issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
System ports are unique identifiers in a multi-ASIC environment that
represent all the available ports in the system. Local ports on the
other hand, are unique only within the local ASIC.
Since system port to local port mapping is not part of the HW-SW
contract and since only single-ASIC configurations are currently
supported, set an explicit 1:1 mapping by configuring the Switch System
Port Record (SSPR) register.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a port's netdevice we should also free the memory
allocated by alloc_etherdev(). Do this by calling free_netdev() at the
end of the teardown sequence.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix double word "the the" in
Documentation/DocBook/networking/API-eth-get-headlen.html
Documentation/DocBook/networking/netdev.html
Documentation/DocBook/networking.xml
These files are generated from comment in source,
so I have to fix comment in net/ethernet/eth.c.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4182 s2 states that if an IPv4 Explicit NULL label is the only
label on the stack, then after popping the resulting packet must be
treated as a IPv4 packet and forwarded based on the IPv4 header. The
same is true for IPv6 Explicit NULL with an IPv6 packet following.
Therefore, when installing the IPv4/IPv6 Explicit NULL label routes,
add an attribute that specifies the expected payload type for use at
forwarding time for determining the type of the encapsulated packet
instead of inspecting the first nibble of the packet.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kaixu Xia says:
====================
bpf: Introduce the new ability of eBPF programs to access hardware PMU counter
This patchset is base on the net-next:
git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git
commit 9dc20a6496.
Previous patch v6 url:
https://lkml.org/lkml/2015/8/4/188
changes in V7:
- rebase the whole patch set to net-next tree(9dc20a64);
- split out the core perf APIs into Patch 1/5;
- change the return value of function perf_event_attrs()
from struct perf_event * to const struct perf_event * in
Patch 1/5;
- rename the function perf_event_read_internal() to perf_event_
read_local() and rewrite it in Patch 1/5;
- rename the function check_func_limit() to check_map_func
_compatibility() and remove the unnecessary pass pointer to
a pointer in Patch 4/5;
changes in V6:
- make the Patch 1/4 commit message more meaning and readable;
- remove the unnecessary comment in Patch 2/4 and make it clean;
- declare the function perf_event_release_kernel() in include/
linux/perf_event.h to fix the build error when CONFIG_PERF_EVENTS
isn't configured in Patch 2/4;
- add function perf_event_attrs() to get the struct perf_event_attr
in Patch 2/4.
- move the related code from kernel/trace/bpf_trace.c to kernel/
events/core.c and add function perf_event_read_internal() to
avoid poking inside of the event outside of perf code in Patch 3/4;
- generial the func & map match-pair with an array in Patch 3/4;
changes in V5:
- move struct fd_array_map_ops* fd_ops to bpf_map;
- move array perf event decrement refcnt function to
map_free;
- fix the NULL ptr of perf_event_get();
- move bpf_perf_event_read() to kernel/bpf/bpf_trace.c;
- get rid of the remaining struct bpf_prog;
- move the unnecessay cast on void *;
changes in V4:
- make the bpf_prog_array_map more generic;
- fix the bug of event refcnt leak;
- use more useful errno in bpf_perf_event_read();
changes in V3:
- collapse V2 patches 1-3 into one;
- drop the function map->ops->map_traverse_elem() and release
the struct perf_event in map_free;
- only allow to access bpf_perf_event_read() from programs;
- update the perf_event_array_map elem via xchg();
- pass index directly to bpf_perf_event_read() instead of
MAP_KEY;
changes in V2:
- put atomic_long_inc_not_zero() between fdget() and fdput();
- limit the event type to PERF_TYPE_RAW and PERF_TYPE_HARDWARE;
- Only read the event counter on current CPU or on current
process;
- add new map type BPF_MAP_TYPE_PERF_EVENT_ARRAY to store the
pointer to the struct perf_event;
- according to the perf_event_map_fd and key, the function
bpf_perf_event_read() can get the Hardware PMU counter value;
Patch 5/5 is a simple example and shows how to use this new eBPF
programs ability. The PMU counter data can be found in
/sys/kernel/debug/tracing/trace(trace_pipe).(the cycles PMU
value when 'kprobe/sys_write' sampling)
$ cat /sys/kernel/debug/tracing/trace_pipe
$ ./tracex6
...
syslog-ng-548 [000] d..1 76.905673: : CPU-0 681765271
syslog-ng-548 [000] d..1 76.905690: : CPU-0 681787855
syslog-ng-548 [000] d..1 76.905707: : CPU-0 681810504
syslog-ng-548 [000] d..1 76.905725: : CPU-0 681834771
syslog-ng-548 [000] d..1 76.905745: : CPU-0 681859519
syslog-ng-548 [000] d..1 76.905766: : CPU-0 681890419
syslog-ng-548 [000] d..1 76.905783: : CPU-0 681914045
syslog-ng-548 [000] d..1 76.905800: : CPU-0 681935950
syslog-ng-548 [000] d..1 76.905816: : CPU-0 681958299
ls-690 [005] d..1 82.241308: : CPU-5 3138451
sh-691 [004] d..1 82.244570: : CPU-4 7324988
<...>-699 [007] d..1 99.961387: : CPU-7 3194027
<...>-695 [003] d..1 99.961474: : CPU-3 288901
<...>-695 [003] d..1 99.961541: : CPU-3 383145
<...>-695 [003] d..1 99.961591: : CPU-3 450365
<...>-695 [003] d..1 99.961639: : CPU-3 515751
<...>-695 [003] d..1 99.961686: : CPU-3 579047
...
The detail of patches is as follow:
Patch 1/5 add the necessary core perf APIs perf_event_attrs(),
perf_event_get(),perf_event_read_local() when accessing events
counters in eBPF programs
Patch 2/5 rewrites part of the bpf_prog_array map code and make it
more generic;
Patch 3/5 introduces a new bpf map type. This map only stores the
pointer to struct perf_event;
Patch 4/5 implements function bpf_perf_event_read() that get the
selected hardware PMU conuter;
Patch 5/5 gives a simple example.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a simple example and shows how to use the new ability
to get the selected Hardware PMU counter value.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the perf_event_map_fd and index, the function
bpf_perf_event_read() can convert the corresponding map
value to the pointer to struct perf_event and return the
Hardware PMU counter value.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new bpf map type 'BPF_MAP_TYPE_PERF_EVENT_ARRAY'.
This map only stores the pointer to struct perf_event. The
user space event FDs from perf_event_open() syscall are converted
to the pointer to struct perf_event and stored in map.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the map backends are of generic nature. In order to avoid
adding much special code into the eBPF core, rewrite part of
the bpf_prog_array map code and make it more generic. So the
new perf_event_array map type can reuse most of code with
bpf_prog_array map and add fewer lines of special code.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add three core perf APIs:
- perf_event_attrs(): export the struct perf_event_attr from struct
perf_event;
- perf_event_get(): get the struct perf_event from the given fd;
- perf_event_read_local(): read the events counters active on the
current CPU;
These APIs are needed when accessing events counters in eBPF programs.
The API perf_event_read_local() comes from Peter and I add the
corresponding SOB.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: support switchdev FDB objects
This patchset refactors the DSA and mv88e6xxx code to use the switchdev FDB
objects.
The first two patches add minor but necessary changes to switchdev, the third
one implements the switchdev glue in DSA for FDB routines, and the remaining
ones refactor the FDB access functions in the mv88e6xxx code.
Below is an usage example (ports 0-2 belongs to br0, ports 3-4 belongs to br1):
# bridge fdb add 3c:97:0e:11:30:6e dev swp2
# bridge fdb add 3c:97:0e:11:40:78 dev swp3
# bridge fdb add 3c:97:0e:11:50:86 dev swp4
# bridge fdb del 3c:97:0e:11:40:78 dev swp3
# bridge fdb
01:00:5e:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth1 self permanent
00:50:d2:10:78:15 dev swp0 master br0 permanent
3c:97:0e:11:30:6e dev swp2 self static
00:50:d2:10:78:15 dev swp3 master br1 permanent
3c:97:0e:11:50:86 dev swp4 self static
# cat /sys/kernel/debug/dsa0/atu
# DB T/P Vec State Addr
# 001 Port 004 e 3c:97:0e:11:30:6e
# 004 Port 010 e 3c:97:0e:11:50:86
For the 88E6xxx switches, FIDs 1 to num_ports will be reserved for non-bridged
ports and bridge groups, and the remaining will be later used by VLANs.
This change is necessary to welcome the support for hardware VLANs (which will
follow soon).
Changes in v2:
- remove ndo_bridge_{get,set,del}link from switchdev/DSA glue code
- use ether_addr_copy instead of memcpy for MAC addresses
- constify MAC address in port_fdb_{add,del}
- split the mv88e6xxx code refactoring into several patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a low level function for the ATU Load operation, and provide FDB add
and delete wrappers functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a low level _mv88e6xxx_atu_getnext function and helpers
to rewrite the mv88e6xxx_port_fdb_getnext operation.
A mv88e6xxx_atu_entry structure is added for convenient access to the
hardware, and GLOBAL_ATU_FID is defined instead of the raw 0x01 value.
The previous implementation did not handle the eventual trunk mapping.
If the related bit is set, then the ATU data register would contain the
trunk ID, and not the port vector.
Check this in the FDB getnext operation and do not handle it (yet).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the __mv88e6xxx_{read,write}_addr functions to more explicit
_mv88e6xxx_atu_mac_{read,write} functions, which also respect the single
underscore convention used in the file (meaning SMI lock must be held).
In the meantime, define their MAC address parameters as an array of
ETH_ALEN bytes instead of a char pointer.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently manages one FID per port (or bridge group), with a
mask of DSA_MAX_PORTS bits, where 0 means that the FID is in use.
The Marvell 88E6xxx switches support up to 4094 FIDs (from 1 to 0xfff;
FID 0 means that multiple address databases are not being used).
This patch changes the fid_mask for an fid_bitmap of 4096 bits.
>From now on, FIDs 1 to num_ports are reserved for non-bridged ports and
bridge groups (a bridge group gets the FID of its first member). The
remaining bits will be reserved for VLAN entries.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harish Patil
Madalin Bucur
Kevin Hao
David S. Miller
Ido Schimmel
Jiri Pirko
Masanari Iida
Shaohui Xie
Robert Shearman
Kaixu Xia
Wang Nan
Vivien Didelot