Pull drm fixes from Dave Airlie:
"A bunch of change across the board, the main things are some vblank
fallout in radeon and nouveau required some work, but I think this
should fix it all. There is also one drm fix for an oops in vmwgfx
with how we pass the drm master around.
The rest is just some amdgpu, i915, imx and rockchip fixes.
Probably more than I'd like at this point, but hopefully things settle
down now"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/nouveau: Fix pre-nv50 pageflip events (v4)
drm: Fix an unwanted master inheritance v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/rockchip: Use CRTC vblank event interface
drm/rockchip: Fix module autoload for OF platform driver
drm/rockchip: vop: fix window origin calculation
...
Pull crypto fixes from Herbert Xu:
"This fixes a couple of crypto drivers that were using memcmp to verify
authentication tags. They now use crypto_memneq instead"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - Fix timing leak in ESP ICV verification
crypto: nx - Fix timing leak in GCM and CCM decryption
A few more last minute fixes for 4.4 on top of my pull request from
earlier this week. The big change here is a vblank regression fix due to
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many vblanks
were missed". Beyond that, a hotplug fix and a few VM fixes.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
add blacklist for thinkpad T40p
drm/amdgpu: fix VM page table reference counting
drm/amdgpu: fix userptr flags check
Pull Ceph fix from Sage Weil:
"This addresses a refcounting bug that leads to a use-after-free"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't put snap_context twice in rbd_queue_workfn()
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Maybe replace the udelay() in the flip_work_func() by a suitable
usleep_range() for a bit better efficiency? Will try that.
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Probably fixes: fdo#93147
Port of Mario's radeon fix to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v2) Refine amdgpu_flip_work_func() for better efficiency.
In amdgpu_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Also small fix to code comment and formatting in that function.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v3) Fix crash in crtc disabled case
Pull libnvdimm fixes from Dan Williams:
- NFIT parsing regression fixes from Linda. The nvdimm hot-add
implementation merged in 4.4-rc1 interpreted the specification in a
way that breaks actual HPE platforms. We are also closing the loop
with the ACPI Working Group to get this clarification added to the
spec.
- Andy pointed out that his laptop without nvdimm resources is loading
the e820-nvdimm module by default, fix that up to only load the
module when an e820-type-12 range is present.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Adjust for different _FIT and NFIT headers
nfit: Fix the check for a successful NFIT merge
nfit: Account for table size length variation
libnvdimm, e820: skip module loading when no type-12
Pull ARM KVM fixes from Paolo Bonzini:
- a series of fixes to deal with the aliasing between the sp and xzr
register
- a fix for the cache flush fix that went in -rc3
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
ARM/arm64: KVM: correct PTE uncachedness check
arm64: KVM: Get rid of old vcpu_reg()
arm64: KVM: Correctly handle zero register in system register accesses
arm64: KVM: Remove const from struct sys_reg_params
arm64: KVM: Correctly handle zero register during MMIO
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Fixes: fdo#93147
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
(v1) Tested-by: Dave Witbrodt <dawitbro@sbcglobal.net>
(v2) Refine radeon_flip_work_func() for better efficiency:
In radeon_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Retested on DCE-3 and DCE-4 to verify it still works nicely.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HPD signals on DVI ports can be fired off before the pins required for
DDC probing actually make contact, due to the pins for HPD making
contact first. This results in a HPD signal being asserted but DDC
probing failing, resulting in hotplugging occasionally failing.
This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.
Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
there is a protection fault about freed list when OCL test.
add a spin lock to protect it.
v2: drop changes in vm_fini
Signed-off-by: JimQu <jim.qu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
KVM/ARM fixes for v4.4-rc4
- A series of fixes to deal with the aliasing between the sp and xzr register
- A fix for the cache flush fix that went in -rc3
Pull sound fixes from Takashi Iwai:
"This time we've got a larger number of updates, mainly from ASoC
world. The only significant LOCs found here are for Realtek codecs,
where most of changes are quite systematic replacements.
There are also a few fixes in ASoC core side: one is the PM call order
fix to ensure the DPAM resume working properly. Another is the proper
cleanup call after freeing DAPM widgets, and the correction of the
wrong callback set in topology API.
The rest are a wide range of driver-specific small fixes, including
HD-audio"
* tag 'sound-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda - Add Conexant CX8200 (14f1:2008) codec entry
ALSA: hda - Correct codec names for 14f1:50f1 and 14f1:50f3
ALSA: hda - Skip ELD notification during system suspend
ASoC: core: Change power state before rechecking endpoint
ASoC: fix kernel-doc warnings in sound/soc/soc-ops.c
ASoC: rt5645: Add dmi_system_id "Google Terra"
ASoC: rockchip: Fix incorrect VDW value for 24 bit
ASoC: fsl: clarify ac97 dependency
ASoC: Intel: Skylake: fix memory leak
ASoC: davinci-mcasp: Fix master capture only mode
ASoC: es8328: Fix shifts for mixer switches
ASoC: rt5645: Add dmi_system_id "Google Wizpig"
ASoC: sti: set player private data
ASoC: sti: rename ST proprietary DT properties
ASoC: sti: remove wrong error message
ASoC: Intel: Skylake: Add I2C depends for SKL machine
ASoC: topology: fix info callback for TLV byte control
ASoC: rt5670: fix wrong bit def for pll src
ASoC: nau8825: add pm function
ASoC: rt5645: Add struct dmi_system_id "Google Edgar" for Chrome OS
...
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix a recent regression in the ACPI PCI host bridge
initialization code, clean up some recent changes (generic power
domains framework, ACPI AML debugger support), fix three older but
annoying bugs (PCI power management. generic power domains framework,
cpufreq) and a build problem (device properties framework), and update
a stale MAINTAINERS entry (ACPI backlight driver).
Specifics:
- Fix a regression in the ACPI PCI host bridge initialization code
introduced by the recent consolidation of the host bridge handling
on x86 and ia64 that forgot to take one special piece of code
related to NUMA on x86 into account (Liu Jiang).
- Improve the Kconfig help description of the new ACPI AML debugger
support option to avoid possible confusion (Peter Zijlstra).
- Remove a piece of code in the generic power domains framework that
should have been removed by one of the recent commits modifying
that code (Ulf Hansson).
- Reduce the log level of a PCI PM message that generates a lot of
false-positive log noise for some drivers and improve the message
itself while at it (Imre Deak).
- Fix the OF-based domain lookup code in the generic power domains
framework to make it drop references to DT nodes correctly (Eric
Anholt).
- Prevent the cpufreq core from setting the policy back to the
default after a CPU offline/online cycle for cpufreq drivers
providing the ->setpolicy callback (Srinivas Pandruvada).
- Fix a build problem for CONFIG_ACPI unset in the device properties
framework (Hanjun Guo).
- Fix a stale file path in the ACPI backlight driver entry in
MAINTAINERS (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
cpufreq: use last policy after online for drivers with ->setpolicy
PCI / PM: Tune down retryable runtime suspend error messages
PM / Domains: Validate cases of a non-bound driver in genpd governor
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
x86/PCI/ACPI: Fix regression caused by commit 4d6b4e69a2
ACPI: Better describe ACPI_DEBUGGER
Commit e6fab54423 ("ARM/arm64: KVM: test properly for a PTE's
uncachedness") modified the logic to test whether a HYP or stage-2
mapping needs flushing, from [incorrectly] interpreting the page table
attributes to [incorrectly] checking whether the PFN that backs the
mapping is covered by host system RAM. The PFN number is part of the
output of the translation, not the input, so we have to use pte_pfn()
on the contents of the PTE, not __phys_to_pfn() on the HYP virtual
address or stage-2 intermediate physical address.
Fixes: e6fab54423 ("ARM/arm64: KVM: test properly for a PTE's uncachedness")
Cc: stable@vger.kernel.org
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Using oldstyle vcpu_reg() accessor is proven to be inappropriate and
unsafe on ARM64. This patch converts the rest of use cases to new
accessors and completely removes vcpu_reg() on ARM64.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
System register accesses also use zero register for Rt == 31, and
therefore using it will also result in getting SP value instead. This
patch makes them also using new accessors, introduced by the previous
patch. Since register value is no longer directly associated with storage
inside vCPU context structure, we introduce a dedicated storage for it in
struct sys_reg_params.
This refactor also gets rid of "massive hack" in kvm_handle_cp_64().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Further rework is going to introduce a dedicated storage for transfer
register value in struct sys_reg_params. Before doing this we have to
remove 'const' modifiers from it in all accessor functions and their
callers.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On ARM64 register index of 31 corresponds to both zero register and SP.
However, all memory access instructions, use ZR as transfer register. SP
is used only as a base register in indirect memory addressing, or by
register-register arithmetics, which cannot be trapped here.
Correct emulation is achieved by introducing new register accessor
functions, which can do special handling for reg_num == 31. These new
accessors intentionally do not rely on old vcpu_reg() on ARM64, because
it is to be removed. Since the affected code is shared by both ARM
flavours, implementations of these accessors are also added to ARM32 code.
This patch fixes setting MMIO register to a random value (actually SP)
instead of zero by something like:
*((volatile int *)reg) = 0;
compilers tend to generate "str wzr, [xx]" here
[Marc: Fixed 32bit splat]
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 4e752f0ab0 ("rbd: access snapshot context and mapping size
safely") moved ceph_get_snap_context() out of rbd_img_request_create()
and into rbd_queue_workfn(), adding a ceph_put_snap_context() to the
error path in rbd_queue_workfn(). However, rbd_img_request_create()
consumes a ref on snapc, so calling ceph_put_snap_context() after
a successful rbd_img_request_create() leads to an extra put. Fix it.
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
* pm-domains:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
PM / Domains: Validate cases of a non-bound driver in genpd governor
* pm-cpufreq:
cpufreq: use last policy after online for drivers with ->setpolicy
Linus Torvalds
Dave Airlie
Alex Deucher
Mario Kleiner
Lyude
jimqu
Christian König
Paolo Bonzini
Ard Biesheuvel
Pavel Fedin
Ilya Dryomov
Rafael J. Wysocki